[ 0.000000] Linux version 4.18.0rh8.10-debug (green@maintenance) (gcc version 8.5.0 20210514 (Red Hat 8.5.0-26) (GCC)) #2 SMP Mon Jul 14 01:24:22 EDT 2025 [ 0.000000] Command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.000000] signal: max sigframe size: 1776 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffd9fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bffda000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000146dfffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-8.fc42 06/10/2025 [ 0.000000] Hypervisor detected: KVM [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: using sched offset of 338827207 cycles [ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.000000] tsc: Detected 2400.000 MHz processor [ 0.000000] last_pfn = 0x146e00 max_arch_pfn = 0x400000000 [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] last_pfn = 0xbffda max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f54d0-0x000f54df] [ 0.000000] RAMDISK: [mem 0xbcc64000-0xbffcffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F52F0 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x00000000BFFE2421 000034 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x00000000BFFE22BD 000074 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x00000000BFFE0040 00227D (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACS 0x00000000BFFE0000 000040 [ 0.000000] ACPI: APIC 0x00000000BFFE2331 000090 (v03 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x00000000BFFE23C1 000038 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: WAET 0x00000000BFFE23F9 000028 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: Reserving FACP table memory at [mem 0xbffe22bd-0xbffe2330] [ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xbffe0040-0xbffe22bc] [ 0.000000] ACPI: Reserving FACS table memory at [mem 0xbffe0000-0xbffe003f] [ 0.000000] ACPI: Reserving APIC table memory at [mem 0xbffe2331-0xbffe23c0] [ 0.000000] ACPI: Reserving HPET table memory at [mem 0xbffe23c1-0xbffe23f8] [ 0.000000] ACPI: Reserving WAET table memory at [mem 0xbffe23f9-0xbffe2420] [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000146dfffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x1465a3000-0x1465cdfff] [ 0.000000] Reserving 256MB of memory at 2752MB for crashkernel (System RAM: 4205MB) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000bffd9fff] [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Zeroed struct page in unavailable ranges: 4744 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000146dfffff] [ 0.000000] ACPI: PM-Timer IO Port: 0x608 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] TSC deadline timer available [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] kvm-guest: KVM setup pv remote TLB flush [ 0.000000] kvm-guest: setup PV sched yield [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbffda000-0xbfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfeffbfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeffc000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] [mem 0xc0000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.000000] kvm-guest: PV spinlocks enabled [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1059618 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] Specific versions of hardware are certified with Red Hat Enterprise Linux 8. Please see the list of hardware certified with Red Hat Enterprise Linux 8 at https://catalog.redhat.com. [ 0.000000] audit: disabled (until reboot) [ 0.000000] software IO TLB: area num 4. [ 0.000000] Memory: 2829700K/4306400K available (18435K kernel code, 11221K rwdata, 7248K rodata, 2908K init, 18040K bss, 524580K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] ftrace: allocating 41240 entries in 162 pages [ 0.000000] ftrace: allocated 162 pages with 3 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.000000] rcu: RCU callback double-/use-after-free debug enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x622/0x9a8 with crng_init=0 [ 0.001000] Console: colour *CGA 80x25 [ 0.001000] printk: console [ttyS1] enabled [ 0.001000] ACPI: Core revision 20220331 [ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.001009] APIC: Switch to symmetric I/O mode setup [ 0.001968] x2apic enabled [ 0.002005] Switched APIC routing to physical x2apic. [ 0.003005] kvm-guest: setup PV IPIs [ 0.005245] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.006000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x22983777dd9, max_idle_ns: 440795300422 ns [ 0.006009] Calibrating delay loop (skipped) preset value.. 4800.00 BogoMIPS (lpj=2400000) [ 0.007004] pid_max: default: 32768 minimum: 301 [ 0.007841] LSM: Security Framework initializing [ 0.008022] Yama: becoming mindful. [ 0.009016] SELinux: Initializing. [ 0.009578] *** VALIDATE selinux *** [ 0.015469] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc) [ 0.019223] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc) [ 0.020074] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.021051] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.022047] *** VALIDATE tmpfs *** [ 0.023032] *** VALIDATE proc *** [ 0.023697] *** VALIDATE cgroup *** [ 0.024003] *** VALIDATE cgroup2 *** [ 0.025065] x86/cpu: User Mode Instruction Prevention (UMIP) activated [ 0.026083] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.027002] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.028015] Spectre V2 : User space: Vulnerable [ 0.028770] Speculative Store Bypass: Vulnerable [ 0.030962] debug: unmapping init [mem 0xffffffffa5859000-0xffffffffa5860fff] [ 0.031848] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz (family: 0x6, model: 0x3e, stepping: 0x4) [ 0.032365] Performance Events: IvyBridge events, full-width counters, Intel PMU driver. [ 0.033008] ... version: 2 [ 0.033705] ... bit width: 48 [ 0.034005] ... generic registers: 4 [ 0.034708] ... value mask: 0000ffffffffffff [ 0.035005] ... max period: 00007fffffffffff [ 0.035887] ... fixed-purpose events: 3 [ 0.036005] ... event mask: 000000070000000f [ 0.036946] rcu: Hierarchical SRCU implementation. [ 0.037951] smp: Bringing up secondary CPUs ... [ 0.038320] x86: Booting SMP configuration: [ 0.039009] .... node #0, CPUs: #1 #2 #3 [ 0.041246] smp: Brought up 1 node, 4 CPUs [ 0.042730] smpboot: Max logical packages: 1 [ 0.043005] smpboot: Total of 4 processors activated (19200.00 BogoMIPS) [ 0.113012] node 0 deferred pages initialised in 69ms [ 0.115468] devtmpfs: initialized [ 0.116132] x86/mm: Memory block size: 128MB [ 0.117924] gcov: version magic: 0x41383552 [ 0.118460] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.119042] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc) [ 0.120140] pinctrl core: initialized pinctrl subsystem [ 0.121094] [ 0.121400] ************************************************************* [ 0.122006] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.123005] ** ** [ 0.124004] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.125005] ** ** [ 0.126005] ** This means that this kernel is built to expose internal ** [ 0.127005] ** IOMMU data structures, which may compromise security on ** [ 0.128005] ** your system. ** [ 0.129005] ** ** [ 0.130005] ** If you see this message and you are not debugging the ** [ 0.131004] ** kernel, report this immediately to your vendor! ** [ 0.132005] ** ** [ 0.133005] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.134006] ************************************************************* [ 0.135313] NET: Registered protocol family 16 [ 0.136244] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.137035] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.138022] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.139207] cpuidle: using governor menu [ 0.140000] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.141222] PCI: Using configuration type 1 for base access [ 0.142074] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on [ 0.147059] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.148009] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.149079] cryptd: max_cpu_qlen set to 1000 [ 0.150151] ACPI: Added _OSI(Module Device) [ 0.151015] ACPI: Added _OSI(Processor Device) [ 0.151847] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.151847] ACPI: Added _OSI(Processor Aggregator Device) [ 0.154746] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 0.158252] ACPI: Interpreter enabled [ 0.158783] ACPI: PM: (supports S0 S3 S4 S5) [ 0.159006] ACPI: Using IOAPIC for interrupt routing [ 0.159863] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.162210] ACPI: Enabled 2 GPEs in block 00 to 0F [ 0.168025] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.169015] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI HPX-Type3] [ 0.170006] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI] [ 0.172027] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.173746] acpiphp: Slot [2] registered [ 0.175040] acpiphp: Slot [5] registered [ 0.175732] acpiphp: Slot [6] registered [ 0.176038] acpiphp: Slot [3] registered [ 0.176706] acpiphp: Slot [4] registered [ 0.178036] acpiphp: Slot [7] registered [ 0.178737] acpiphp: Slot [8] registered [ 0.179034] acpiphp: Slot [9] registered [ 0.179668] acpiphp: Slot [10] registered [ 0.180036] acpiphp: Slot [11] registered [ 0.180709] acpiphp: Slot [12] registered [ 0.182036] acpiphp: Slot [13] registered [ 0.182740] acpiphp: Slot [14] registered [ 0.183035] acpiphp: Slot [15] registered [ 0.183710] acpiphp: Slot [16] registered [ 0.184045] acpiphp: Slot [17] registered [ 0.184779] acpiphp: Slot [18] registered [ 0.186036] acpiphp: Slot [19] registered [ 0.186732] acpiphp: Slot [20] registered [ 0.187035] acpiphp: Slot [21] registered [ 0.187684] acpiphp: Slot [22] registered [ 0.188043] acpiphp: Slot [23] registered [ 0.188782] acpiphp: Slot [24] registered [ 0.190040] acpiphp: Slot [25] registered [ 0.190745] acpiphp: Slot [26] registered [ 0.191047] acpiphp: Slot [27] registered [ 0.191823] acpiphp: Slot [28] registered [ 0.193036] acpiphp: Slot [29] registered [ 0.193761] acpiphp: Slot [30] registered [ 0.194036] acpiphp: Slot [31] registered [ 0.194737] PCI host bridge to bus 0000:00 [ 0.196010] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.197016] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.198007] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.199010] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.200007] pci_bus 0000:00: root bus resource [mem 0xe0000000000-0xe007fffffff window] [ 0.202009] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.203026] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.204569] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.205636] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.209582] pci 0000:00:01.1: reg 0x20: [io 0xc120-0xc12f] [ 0.212031] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.213007] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.214007] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.215006] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.217415] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.218444] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI [ 0.220017] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB [ 0.221495] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 [ 0.222869] pci 0000:00:02.0: reg 0x10: [io 0xc100-0xc11f] [ 0.228396] pci 0000:00:02.0: reg 0x20: [mem 0xe0000000000-0xe0000003fff 64bit pref] [ 0.229712] pci 0000:00:02.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref] [ 0.232797] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.236013] pci 0000:00:05.0: reg 0x10: [io 0xc000-0xc07f] [ 0.239010] pci 0000:00:05.0: reg 0x14: [mem 0xfebc0000-0xfebc0fff] [ 0.245015] pci 0000:00:05.0: reg 0x20: [mem 0xe0000004000-0xe0000007fff 64bit pref] [ 0.250525] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.253014] pci 0000:00:06.0: reg 0x10: [io 0xc080-0xc0ff] [ 0.255717] pci 0000:00:06.0: reg 0x14: [mem 0xfebc1000-0xfebc1fff] [ 0.261009] pci 0000:00:06.0: reg 0x20: [mem 0xe0000008000-0xe000000bfff 64bit pref] [ 0.266842] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.269253] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 0.271245] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 0.272239] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 0.274125] ACPI: PCI: Interrupt link LNKS configured for IRQ 9 [ 0.278134] iommu: Default domain type: Passthrough [ 0.279277] SCSI subsystem initialized [ 0.280000] ACPI: bus type USB registered [ 0.281081] usbcore: registered new interface driver usbfs [ 0.282044] usbcore: registered new interface driver hub [ 0.282981] usbcore: registered new device driver usb [ 0.284073] pps_core: LinuxPPS API ver. 1 registered [ 0.284924] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.286015] PTP clock support registered [ 0.287132] EDAC MC: Ver: 3.0.0 [ 0.288101] PCI: Using ACPI for IRQ routing [ 0.289601] NetLabel: Initializing [ 0.291008] NetLabel: domain hash size = 128 [ 0.292006] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.294050] NetLabel: unlabeled traffic allowed by default [ 0.295107] vgaarb: loaded [ 0.296262] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.297008] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.304200] clocksource: Switched to clocksource kvm-clock [ 0.369573] VFS: Disk quotas dquot_6.6.0 [ 0.370342] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.371573] *** VALIDATE ramfs *** [ 0.372162] *** VALIDATE hugetlbfs *** [ 0.372858] pnp: PnP ACPI init [ 0.374111] pnp: PnP ACPI: found 6 devices [ 0.387197] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.389033] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.390146] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.391219] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.392450] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.393687] pci_bus 0000:00: resource 8 [mem 0xe0000000000-0xe007fffffff window] [ 0.395143] NET: Registered protocol family 2 [ 0.396583] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc) [ 0.399694] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, vmalloc) [ 0.402400] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc) [ 0.406151] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc) [ 0.408657] TCP: Hash tables configured (established 65536 bind 65536) [ 0.410104] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, vmalloc) [ 0.411753] UDP hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.413143] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.414623] NET: Registered protocol family 1 [ 0.415987] RPC: Registered named UNIX socket transport module. [ 0.417099] RPC: Registered udp transport module. [ 0.417989] RPC: Registered tcp transport module. [ 0.418906] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.420143] NET: Registered protocol family 44 [ 0.421079] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.422113] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.423112] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.424167] PCI: CLS 0 bytes, default 64 [ 0.425059] Unpacking initramfs... [ 1.560465] debug: unmapping init [mem 0xffff89aa7cc64000-0xffff89aa7ffcffff] [ 1.563634] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.565467] software IO TLB: mapped [mem 0x00000000a8000000-0x00000000ac000000] (64MB) [ 1.567746] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x22983777dd9, max_idle_ns: 440795300422 ns [ 2.029247] Initialise system trusted keyrings [ 2.030729] Key type blacklist registered [ 2.033619] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 2.062748] zbud: loaded [ 2.064947] *** VALIDATE nfs *** [ 2.065892] *** VALIDATE nfs4 *** [ 2.067037] pstore: using deflate compression [ 2.070446] Platform Keyring initialized [ 2.164225] NET: Registered protocol family 38 [ 2.165845] Key type asymmetric registered [ 2.167098] Asymmetric key parser 'x509' registered [ 2.168788] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.171595] io scheduler mq-deadline registered [ 2.175316] io scheduler kyber registered [ 2.178735] io scheduler bfq registered [ 2.182143] atomic64_test: passed for x86-64 platform with CX8 and with SSE [ 2.185489] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.187313] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 2.189075] ACPI: Power Button [PWRF] [ 2.192754] ACPI: \_SB_.LNKB: Enabled at IRQ 10 [ 2.197632] ACPI: \_SB_.LNKA: Enabled at IRQ 11 [ 2.205807] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.232804] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.263575] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.269683] Non-volatile memory driver v1.3 [ 2.272651] Linux agpgart interface v0.103 [ 2.301830] virtio_blk virtio1: [vda] 134664 512-byte logical blocks (68.9 MB/65.8 MiB) [ 2.304415] vda: detected capacity change from 0 to 68947968 [ 2.319739] virtio_blk virtio2: [vdb] 2097152 512-byte logical blocks (1.07 GB/1.00 GiB) [ 2.322412] vdb: detected capacity change from 0 to 1073741824 [ 2.329288] libphy: Fixed MDIO Bus: probed [ 2.334558] usbcore: registered new interface driver usbserial_generic [ 2.336733] usbserial: USB Serial support registered for generic [ 2.338833] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 2.343315] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.344727] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.346729] mousedev: PS/2 mouse device common for all mice [ 2.350256] rtc_cmos 00:05: RTC can wake from S4 [ 2.352506] rtc_cmos 00:05: registered as rtc0 [ 2.353948] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs [ 2.356379] intel_pstate: CPU model not supported [ 2.359664] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 2.359861] hid: raw HID events driver (C) Jiri Kosina [ 2.364498] usbcore: registered new interface driver usbhid [ 2.366472] usbhid: USB HID core driver [ 2.367096] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input4 [ 2.367798] drop_monitor: Initializing network drop monitor service [ 2.373347] Initializing XFRM netlink socket [ 2.375526] NET: Registered protocol family 10 [ 2.375851] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input3 [ 2.378299] Segment Routing with IPv6 [ 2.382320] NET: Registered protocol family 17 [ 2.384587] mpls_gso: MPLS GSO support [ 2.390769] RAS: Correctable Errors collector initialized. [ 2.392377] AVX version of gcm_enc/dec engaged. [ 2.393710] AES CTR mode by8 optimization enabled [ 2.498715] sched_clock: Marking stable (2498637280, 0)->(3017483383, -518846103) [ 2.503742] registered taskstats version 1 [ 2.506427] Loading compiled-in X.509 certificates [ 2.510531] zswap: loaded using pool lzo/zbud [ 2.544763] Key type big_key registered [ 2.558524] Key type encrypted registered [ 2.563067] ima: No TPM chip found, activating TPM-bypass! [ 2.568282] ima: Allocated hash algorithm: sha1 [ 2.570971] ima: No architecture policies found [ 2.573356] evm: Initialising EVM extended attributes: [ 2.575157] evm: security.selinux [ 2.576178] evm: security.ima [ 2.577448] evm: security.capability [ 2.579008] evm: HMAC attrs: 0x1 [ 2.583227] rtc_cmos 00:05: setting system clock to 2026-03-07 17:52:40 UTC (1772905960) [ 2.589390] debug: unmapping init [mem 0xffffffffa6803000-0xffffffffa69fffff] [ 2.592688] debug: unmapping init [mem 0xffffffffa5582000-0xffffffffa5858fff] [ 2.601127] Write protecting the kernel read-only data: 28672k [ 2.603745] debug: unmapping init [mem 0xffffffffa3c03000-0xffffffffa3dfffff] [ 2.605528] debug: unmapping init [mem 0xffffffffa4514000-0xffffffffa45fffff] [ 2.655853] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 2.668869] systemd[1]: Detected virtualization kvm. [ 2.670858] systemd[1]: Detected architecture x86-64. [ 2.673048] systemd[1]: Running in initial RAM disk. Welcome to Rocky Linux 8.10 (Green Obsidian) dracut-049-233.git20240115.el8 (Initramfs)! [ 2.711293] systemd[1]: No hostname configured. [ 2.714338] systemd[1]: Set hostname to . [ 2.717319] random: systemd: uninitialized urandom read (16 bytes read) [ 2.722752] systemd[1]: Initializing machine ID from random generator. [ 2.949283] random: systemd: uninitialized urandom read (16 bytes read) [ 2.953970] systemd[1]: Reached target Local File Systems. [ OK ] Reached target Local File Systems. [ 2.964118] random: systemd: uninitialized urandom read (16 bytes read) [ 2.970342] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 2.986957] systemd[1]: Starting Create Volatile Files and Directories... Starting Create Volatile Files and Directories... Starting Setup Virtual Console... [ OK ] Started Memstrack Anylazing Service. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Reached target Swap. [ OK ] Reached target Initrd Root Device. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Reached target Timers. [ OK ] Listening on udev Control Socket. Starting Apply Kernel Variables... [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Slices. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Setup Virtual Console. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Apply Kernel Variables. Starting Create Static Device Nodes in /dev... Starting dracut cmdline hook... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Journal Service. [ OK ] Started dracut cmdline hook. Starting dracut pre-udev hook... [ 4.047919] device-mapper: uevent: version 1.0.3 [ 4.050762] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ OK ] Started dracut pre-udev hook. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook. Starting udev Coldplug all Devices... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting dracut initqueue hook... [ 5.549207] random: fast init done [ 5.551661] virtio_net virtio0 ens2: renamed from eth0 [ 5.871270] scsi host0: ata_piix [ 5.944469] scsi host1: ata_piix [ 5.949726] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc120 irq 14 [ 5.959332] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc128 irq 15 [ 11.105777] random: crng init done [ 11.112313] random: 7 urandom warning(s) missed due to ratelimiting [ 13.336686] dracut-initqueue[582]: RTNETLINK answers: File exists Starting nbd nbd0... [ OK ] Started nbd nbd0. [ OK ] Started dracut initqueue hook. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting /sysroot... [ 14.699397] EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /sysroot. [ OK ] Reached target Initrd Root File System. Starting Reload Configuration from the Real Root... [ OK ] Started Reload Configuration from the Real Root. [ OK ] Reached target Initrd File Systems. [ OK ] Reached target Initrd Default Target. Starting dracut pre-pivot and cleanup hook... [ OK ] Started dracut pre-pivot and cleanup hook. Starting Cleaning Up and Shutting Down Daemons... Stopping Hardware RNG Entropy Gatherer Daemon... [ OK ] Stopped dracut pre-pivot and cleanup hook. [ OK ] Stopped target Initrd Default Target. [ OK ] Stopped target Initrd Root Device. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped dracut initqueue hook. [ OK ] Stopped target Timers. [ OK ] Stopped Hardware RNG Entropy Gatherer Daemon. [ OK ] Stopped target Basic System. [ OK ] Stopped target Sockets. [ OK ] Stopped target Paths. [ OK ] Stopped target Slices. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped udev Coldplug all Devices. [ OK ] Stopped dracut pre-trigger hook. Stopping udev Kernel Device Manager... [ OK ] Stopped target Swap. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. [ OK ] Started Cleaning Up and Shutting Down Daemons. [ OK ] Stopped udev Kernel Device Manager. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create list of required sta…vice nodes for the current kernel. [ OK ] Stopped dracut pre-udev hook. [ OK ] Stopped dracut cmdline hook. [ OK ] Closed udev Kernel Socket. [ OK ] Closed udev Control Socket. Starting Cleanup udevd DB... [ OK ] Started Cleanup udevd DB. [ OK ] Reached target Switch Root. Starting Switch Root... [ 16.111346] printk: systemd: 26 output lines suppressed due to ratelimiting [ 16.415692] SELinux: Disabled at runtime. [ 16.481875] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 16.490284] systemd[1]: Detected virtualization kvm. [ 16.491509] systemd[1]: Detected architecture x86-64. Welcome to Rocky Linux 8.10 (Green Obsidian)! [ 17.093358] systemd[1]: initrd-switch-root.service: Succeeded. [ 17.096948] systemd[1]: Stopped Switch Root. [ OK ] Stopped Switch Root. [ 17.105578] systemd[1]: systemd-journald.service: Service has no hold-off time (RestartSec=0), scheduling restart. [ 17.109729] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1. [ 17.113614] systemd[1]: Stopped Journal Service. [ OK ] Stopped Journal Service. [ 17.122263] systemd[1]: Starting Journal Service... Starting Journal Service... [ 17.127539] systemd[1]: Reached target rpc_pipefs.target. [ OK ] Reached target rpc_pipefs.target. [ OK ] Created slice system-sshd\x2dkeygen.slice. [ OK ] Listening on RPCbind Server Activation Socket. Starting Remount Root and Kernel File Systems... Activating swap /dev/disk/by-label/SWAP... [ OK ] Created slice system-serial\x2dgetty.slice. Starting Apply Kernel Variables... [ 17.178105] Adding 1048572k swap on /dev/vdb. Priority:-2 extents:1 across:1048572k FS [ OK ] Listening on Process Core Dump Socket. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target RPC Port Mapper. Mounting Kernel Debug File System... [ OK ] Listening on initctl Compatibility Named Pipe. Mounting Huge Pages File System... [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice system-getty.slice. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Stopped target Switch Root. [ OK ] Stopped target Initrd Root File System. [ OK ] Stopped target Initrd File Systems. [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... Mounting POSIX Message Queue File System... [FAILED] Failed to set up automount Arbitrar…rmats File System Automount Point. See 'systemctl status proc-sys-fs-binfmt_misc.automount' for details. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Started Journal Service. [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. [ OK ] Activated swap /dev/disk/by-label/SWAP. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Reached target Swap. Starting Create Static Device Nodes in /dev... Starting Configure read-only root support... Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /home/green/git/lustre-release... Mounting /mnt... [ OK ] Started udev Coldplug all Devices. [ OK ] Mounted /mnt. [ 17.815641] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ OK ] Mounted /home/green/git/lustre-release. [ OK ] Started udev Kernel Device Manager. [ 18.437093] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0 [ 18.437681] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 18.923223] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer [ 18.945714] EDAC sbridge: Ver: 1.1.2 [ 21.125961] Key type dns_resolver registered [ 21.517727] NFS: Registering the id_resolver key type [ 21.520162] Key type id_resolver registered [ 21.522023] Key type id_legacy registered [ OK ] Started Configure read-only root support. [ OK ] Reached target Local File Systems. Starting Mark the need to relabel after reboot... Starting Create Volatile Files and Directories... Starting Rebuild Dynamic Linker Cache... Starting Load/Save Random Seed... [ OK ] Started Mark the need to relabel after reboot. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting RPC Bind... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC Bind. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started daily update of the root trust anchor for DNSSEC. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Network Manager... Starting Login Service... [ OK ] Started dnf makecache --timer. Starting Restore /run/initramfs on shutdown... [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started irqbalance daemon. [ OK ] Reached target sshd-keygen.target. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Started Restore /run/initramfs on shutdown. [ OK ] Started Login Service. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting Dynamic System Tuning Daemon... Starting GSSAPI Proxy Daemon... Starting OpenSSH server daemon... Starting Network Manager Wait Online... Starting Hostname Service... [ OK ] Started GSSAPI Proxy Daemon. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started OpenSSH server daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Command Scheduler. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Serial Getty on ttyS1. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting Notify NFS peers of a restart... Starting System Logging Service... Starting Crash recovery kernel arming... [ OK ] Started Notify NFS peers of a restart. [ OK ] Started System Logging Service. Starting Authorization Manager... [ OK ] Started Dynamic System Tuning Daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Started Authorization Manager. Rocky Linux 8.10 (Green Obsidian) Kernel 4.18.0rh8.10-debug on an x86_64 oleg404-client login: [ 57.500887] libcfs: loading out-of-tree module taints kernel. [ 57.523899] Key type ._llcrypt registered [ 57.526299] Key type .llcrypt registered [ 57.829897] libcfs: HW NUMA nodes: 1, HW CPU cores: 4, npartitions: 2 [ 57.835501] alg: No test for adler32 (adler32-zlib) [ 58.790094] Lustre: Lustre: Build Version: 2.17.50_193_g952cf82 [ 59.022433] LNet: Added LNI 192.168.204.4@tcp [8/256/0/180] [ 60.616187] Key type lgssc registered [ 61.131362] Lustre: Echo OBD driver; http://www.lustre.org/ [ 120.641897] Lustre: Mounted lustre-client [ 123.096057] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 135.811746] Lustre: DEBUG MARKER: oleg404-client.virtnet: executing check_logdir /tmp/testlogs/ [ 137.399211] Lustre: DEBUG MARKER: oleg404-client.virtnet: executing yml_node [ 139.066436] Lustre: DEBUG MARKER: Client: 2.17.50.193 [ 140.014183] Lustre: DEBUG MARKER: MDS: 2.17.50.193 [ 140.917127] Lustre: DEBUG MARKER: OSS: 2.17.50.193 [ 141.546382] Lustre: DEBUG MARKER: -----============= acceptance-small: sanity-sec ============----- Sat Mar 7 12:54:58 EST 2026 [ 146.400282] Lustre: lustre-OST0000-osc-ffff89aae0a7b000: disconnect after 24s idle [ 148.476536] Lustre: DEBUG MARKER: excepting tests: 27 [ 149.186965] Lustre: DEBUG MARKER: skipping tests SLOW=no: 26 [ 150.331599] Lustre: DEBUG MARKER: === sanity-sec: start setup 12:55:07 (1772906107) === [ 151.908466] Lustre: DEBUG MARKER: oleg404-client.virtnet: executing check_config_client /mnt/lustre [ 159.952888] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 165.366265] Lustre: DEBUG MARKER: === sanity-sec: finish setup 12:55:22 (1772906122) === [ 168.828944] Lustre: DEBUG MARKER: == sanity-sec test 0: uid permission ======================================================================================= 12:55:26 (1772906126) [ 171.589439] Lustre: DEBUG MARKER: == sanity-sec test 1: setuid/gid ======================================================================================= 12:55:28 (1772906128) [ 172.267808] Lustre: DEBUG MARKER: SKIP: sanity-sec test_1 without GSS support. [ 172.926582] Lustre: DEBUG MARKER: == sanity-sec test 4: set supplementary group ========================================================================= 12:55:30 (1772906130) [ 181.599672] Lustre: DEBUG MARKER: == sanity-sec test 7: nodemap create and delete ========== 12:55:38 (1772906138) [ 192.480212] Lustre: lustre-OST0000-osc-ffff89aae0a7b000: disconnect after 23s idle [ 192.486624] Lustre: Skipped 1 previous similar message [ 194.534341] Lustre: DEBUG MARKER: == sanity-sec test 8: nodemap reject duplicates ========== 12:55:51 (1772906151) [ 210.878325] Lustre: DEBUG MARKER: == sanity-sec test 9: nodemap range add ================== 12:56:08 (1772906168) [ 226.826989] Lustre: DEBUG MARKER: == sanity-sec test 10a: nodemap reject duplicate ranges == 12:56:24 (1772906184) [ 243.248749] Lustre: DEBUG MARKER: == sanity-sec test 10b: delete range from the correct nodemap ========================================================== 12:56:40 (1772906200) [ 248.347839] Lustre: DEBUG MARKER: == sanity-sec test 10c: verfify contiguous range support ========================================================== 12:56:45 (1772906205) [ 252.490300] Lustre: DEBUG MARKER: == sanity-sec test 10d: verfify nodemap range format '*@' support ========================================================== 12:56:49 (1772906209) [ 256.780783] Lustre: DEBUG MARKER: == sanity-sec test 11: nodemap modify ==================== 12:56:54 (1772906214) [ 272.717392] Lustre: DEBUG MARKER: == sanity-sec test 12: nodemap set squash ids ============ 12:57:10 (1772906230) [ 287.326989] Lustre: DEBUG MARKER: == sanity-sec test 13: test nids ========================= 12:57:24 (1772906244) [ 305.892315] Lustre: DEBUG MARKER: == sanity-sec test 14: test default nodemap nid lookup === 12:57:43 (1772906263) [ 322.159824] Lustre: DEBUG MARKER: == sanity-sec test 15: test id mapping =================== 12:57:59 (1772906279) [ 383.281994] Lustre: DEBUG MARKER: == sanity-sec test 16: test nodemap all_off fileops ====== 12:59:00 (1772906340) [ 473.531299] Lustre: DEBUG MARKER: == sanity-sec test 17: test nodemap trusted_noadmin fileops ========================================================== 13:00:30 (1772906430) [ 489.440177] Lustre: lustre-OST0001-osc-ffff89aae0a7b000: disconnect after 21s idle [ 489.442895] Lustre: Skipped 1 previous similar message [ 655.711520] Lustre: DEBUG MARKER: == sanity-sec test 18: test nodemap mapped_noadmin fileops ========================================================== 13:03:33 (1772906613) [ 673.760219] Lustre: lustre-OST0001-osc-ffff89aae0a7b000: disconnect after 23s idle [ 752.810830] Lustre: DEBUG MARKER: == sanity-sec test 19: test nodemap trusted_admin fileops ========================================================== 13:05:10 (1772906710) [ 814.144919] Lustre: DEBUG MARKER: == sanity-sec test 20: test nodemap mapped_admin fileops ========================================================== 13:06:11 (1772906771) [ 878.228113] Lustre: DEBUG MARKER: == sanity-sec test 21: test nodemap mapped_trusted_noadmin fileops ========================================================== 13:07:15 (1772906835) [ 893.920224] Lustre: lustre-OST0001-osc-ffff89aae0a7b000: disconnect after 21s idle [ 973.163470] Lustre: DEBUG MARKER: == sanity-sec test 22: test nodemap mapped_trusted_admin fileops ========================================================== 13:08:50 (1772906930) [ 1034.107531] Lustre: DEBUG MARKER: == sanity-sec test 23a: test mapped regular ACLs ========= 13:09:51 (1772906991) [ 1034.538675] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23a Need 2 clients at least [ 1035.075715] Lustre: DEBUG MARKER: == sanity-sec test 23b: test mapped default ACLs ========= 13:09:52 (1772906992) [ 1035.506917] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23b Need 2 clients at least [ 1036.013222] Lustre: DEBUG MARKER: == sanity-sec test 24: check nodemap proc files for LBUGs and Oopses ========================================================== 13:09:53 (1772906993) [ 1045.820641] Lustre: DEBUG MARKER: == sanity-sec test 25a: test save and reload nodemap config ========================================================== 13:10:03 (1772907003) [ 1046.295673] LustreError: 67109:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aae0a7b000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1046.316746] Lustre: Unmounted lustre-client [ 1055.733217] Lustre: DEBUG MARKER: === sanity-sec: start setup 13:10:13 (1772907013) === [ 1071.436439] LustreError: 68922:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 3087us [ 1071.458192] Lustre: Mounted lustre-client [ 1073.798502] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 1082.426745] Lustre: DEBUG MARKER: === sanity-sec: finish setup 13:10:39 (1772907039) === [ 1082.688818] LustreError: 69904:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac644c800: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1082.691982] LustreError: 69904:0:(lov_obd.c:783:lov_cleanup()) Skipped 1 previous similar message [ 1082.715271] Lustre: Unmounted lustre-client [ 1086.893699] LustreError: 70138:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1189us [ 1086.918638] Lustre: Mounted lustre-client [ 1088.994122] Lustre: DEBUG MARKER: == sanity-sec test 25b: test nodemap info values ========= 13:10:46 (1772907046) [ 1102.797255] Lustre: DEBUG MARKER: == sanity-sec test 25c: test yaml-compliance for nodemap ========================================================== 13:11:00 (1772907060) [ 1110.106145] LustreError: 72360:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac663a000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1110.109145] LustreError: 72360:0:(lov_obd.c:783:lov_cleanup()) Skipped 1 previous similar message [ 1110.131798] Lustre: Unmounted lustre-client [ 1110.235926] LustreError: 72407:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 213us [ 1110.252600] Lustre: Mounted lustre-client [ 1112.619885] LustreError: 72893:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac867f800: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1112.624462] LustreError: 72893:0:(lov_obd.c:783:lov_cleanup()) Skipped 1 previous similar message [ 1112.652025] Lustre: Unmounted lustre-client [ 1115.788827] LustreError: 73096:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 273us [ 1115.803560] Lustre: Mounted lustre-client [ 1116.414665] Lustre: DEBUG MARKER: SKIP: sanity-sec test_26 skipping SLOW test 26 [ 1116.958996] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27a skipping excluded test 27a (base 27) [ 1117.500669] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27aa skipping excluded test 27aa (base 27) [ 1118.001652] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ab skipping excluded test 27ab (base 27) [ 1118.506994] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ac skipping excluded test 27ac (base 27) [ 1118.988136] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27b skipping excluded test 27b (base 27) [ 1119.495954] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27c skipping excluded test 27c (base 27) [ 1120.031877] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27d skipping excluded test 27d (base 27) [ 1120.515146] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27e skipping excluded test 27e (base 27) [ 1121.005183] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27f skipping excluded test 27f (base 27) [ 1121.532099] Lustre: DEBUG MARKER: == sanity-sec test 28: check shared key rotation method == 13:11:18 (1772907078) [ 1121.996079] Lustre: DEBUG MARKER: SKIP: sanity-sec test_28 need shared key feature for this test [ 1122.594181] Lustre: DEBUG MARKER: == sanity-sec test 29: check for missing shared key ====== 13:11:20 (1772907080) [ 1123.102394] Lustre: DEBUG MARKER: SKIP: sanity-sec test_29 need shared key feature for this test [ 1123.659744] Lustre: DEBUG MARKER: == sanity-sec test 30: check for invalid shared key ====== 13:11:21 (1772907081) [ 1124.229895] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30 need shared key feature for this test [ 1124.816336] Lustre: DEBUG MARKER: == sanity-sec test 30b: basic test of all different SSK flavors ========================================================== 13:11:22 (1772907082) [ 1125.386170] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30b need shared key feature for this test [ 1125.933162] Lustre: DEBUG MARKER: == sanity-sec test 31: client mount option '-o network' == 13:11:23 (1772907083) [ 1126.806646] Lustre: DEBUG MARKER: SKIP: sanity-sec test_31 without lnetctl support. [ 1127.334631] Lustre: DEBUG MARKER: == sanity-sec test 32: check for mgssec ================== 13:11:24 (1772907084) [ 1128.150368] Lustre: DEBUG MARKER: SKIP: sanity-sec test_32 need shared key feature for this test [ 1128.696269] Lustre: DEBUG MARKER: == sanity-sec test 33: correct srpc flags for MGS connection ========================================================== 13:11:26 (1772907086) [ 1129.198162] Lustre: DEBUG MARKER: SKIP: sanity-sec test_33 need shared key feature for this test [ 1129.749153] Lustre: DEBUG MARKER: == sanity-sec test 34: deny_unknown on default nodemap === 13:11:27 (1772907087) [ 1137.967460] Lustre: DEBUG MARKER: == sanity-sec test 35: Check permissions when accessing changelogs ========================================================== 13:11:35 (1772907095) [ 1147.355423] LustreError: 78239:0:(mdc_changelog.c:293:chlg_load()) lustre-MDT0000-mdc-ffff89aac30b1000: fail to open changelog catalog: rc = -13 [ 1153.179502] Lustre: DEBUG MARKER: == sanity-sec test 36: control if clients can use encryption ========================================================== 13:11:50 (1772907110) [ 1153.571868] LustreError: 78659:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac30b1000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1153.575136] LustreError: 78659:0:(lov_obd.c:783:lov_cleanup()) Skipped 1 previous similar message [ 1153.599116] Lustre: Unmounted lustre-client [ 1153.713905] LustreError: 78699:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 4034us [ 1153.727103] Lustre: Test dummy encryption mode enabled [ 1153.734996] Lustre: Mounted lustre-client [ 1153.823607] llcrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-aesni)" [ 1155.863723] Lustre: Test dummy encryption mode enabled [ 1157.553528] Lustre: lustre-MDT0001-mdc-ffff89aac880d800: connection denied by lustre-MDT0001_UUID: rc = -13 [ 1157.555893] LustreError: 79004:0:(lmv_obd.c:1434:lmv_statfs()) lustre-MDT0000-mdc-ffff89aac880d800: can't stat MDS #0: rc = -13 [ 1157.582480] LustreError: 79004:0:(super25.c:186:lustre_fill_super()) llite: Unable to mount : rc = -13 [ 1163.703946] LustreError: 79741:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 270us [ 1163.709612] LustreError: 79741:0:(obd_config.c:1466:process_param2_config()) Skipped 2 previous similar messages [ 1163.722831] Lustre: Mounted lustre-client [ 1163.723760] Lustre: Skipped 1 previous similar message [ 1164.047151] LustreError: 79788:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac30b4800: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1164.050524] LustreError: 79788:0:(lov_obd.c:783:lov_cleanup()) Skipped 5 previous similar messages [ 1164.078956] Lustre: Unmounted lustre-client [ 1164.080246] Lustre: Skipped 3 previous similar messages [ 1164.525707] bash (78487): drop_caches: 3 [ 1165.314665] Lustre: DEBUG MARKER: == sanity-sec test 37: simple encrypted file ============= 13:12:02 (1772907122) [ 1165.866413] Lustre: Test dummy encryption mode enabled [ 1165.979436] llcrypt: AES-256-XTS using implementation "xts-aes-aesni" [ 1168.973573] bash (79881): drop_caches: 3 [ 1169.806232] Lustre: DEBUG MARKER: == sanity-sec test 38: encrypted file with hole ========== 13:12:07 (1772907127) [ 1170.462865] Lustre: Test dummy encryption mode enabled [ 1173.042597] bash (80695): drop_caches: 3 [ 1173.826824] Lustre: DEBUG MARKER: == sanity-sec test 39: rewrite data in already encrypted page ========================================================== 13:12:11 (1772907131) [ 1176.644015] bash (81493): drop_caches: 3 [ 1177.404268] Lustre: DEBUG MARKER: == sanity-sec test 40: exercise size of encrypted file === 13:12:14 (1772907134) [ 1177.952431] Lustre: Test dummy encryption mode enabled [ 1177.953947] Lustre: Skipped 1 previous similar message [ 1179.388643] bash (82287): drop_caches: 3 [ 1181.694144] LustreError: 83196:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac644f000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1181.697499] LustreError: 83196:0:(lov_obd.c:783:lov_cleanup()) Skipped 17 previous similar messages [ 1181.726848] Lustre: Unmounted lustre-client [ 1181.727946] Lustre: Skipped 8 previous similar messages [ 1181.898785] LustreError: 83233:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 485us [ 1181.902416] LustreError: 83233:0:(obd_config.c:1466:process_param2_config()) Skipped 9 previous similar messages [ 1181.913514] Lustre: Mounted lustre-client [ 1181.914593] Lustre: Skipped 9 previous similar messages [ 1182.058721] bash (82287): drop_caches: 3 [ 1182.827965] Lustre: DEBUG MARKER: == sanity-sec test 41: test race on encrypted file size (1) ========================================================== 13:12:20 (1772907140) [ 1201.758674] bash (83283): drop_caches: 3 [ 1202.653659] Lustre: DEBUG MARKER: == sanity-sec test 42: test race on encrypted file size (2) ========================================================== 13:12:39 (1772907159) [ 1203.230982] Lustre: Test dummy encryption mode enabled [ 1203.232618] Lustre: Skipped 1 previous similar message [ 1221.387307] LustreError: 84880:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac644c800: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1221.390689] LustreError: 84880:0:(lov_obd.c:783:lov_cleanup()) Skipped 7 previous similar messages [ 1221.416141] Lustre: Unmounted lustre-client [ 1221.417264] Lustre: Skipped 3 previous similar messages [ 1221.502043] LustreError: 84899:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 244us [ 1221.508168] LustreError: 84899:0:(obd_config.c:1466:process_param2_config()) Skipped 4 previous similar messages [ 1221.521737] Lustre: Mounted lustre-client [ 1221.523419] Lustre: Skipped 4 previous similar messages [ 1222.013493] bash (84099): drop_caches: 3 [ 1222.848129] Lustre: DEBUG MARKER: == sanity-sec test 43: test race on encrypted file size (3) ========================================================== 13:13:00 (1772907180) [ 1223.445616] Lustre: Test dummy encryption mode enabled [ 1223.446874] Lustre: Skipped 1 previous similar message [ 1242.038901] bash (84972): drop_caches: 3 [ 1242.942584] Lustre: DEBUG MARKER: == sanity-sec test 44: encrypted file access semantics: direct IO ========================================================== 13:13:20 (1772907200) [ 1243.575874] Lustre: DEBUG MARKER: SKIP: sanity-sec test_44 This test needs vmtouch utility [ 1244.121247] Lustre: DEBUG MARKER: == sanity-sec test 45: encrypted file access semantics: MMAP ========================================================== 13:13:21 (1772907201) [ 1247.075750] bash (86147): drop_caches: 3 [ 1247.957813] Lustre: DEBUG MARKER: == sanity-sec test 46: encrypted file access semantics without key ========================================================== 13:13:25 (1772907205) [ 1248.942813] bash (86937): drop_caches: 3 [ 1249.809237] bash (86937): drop_caches: 3 [ 1250.133060] LustreError: 87325:0:(llite_lib.c:3981:ll_prep_md_op_data()) lustre: failed to setup filename: rc = -126 [ 1252.856495] bash (86937): drop_caches: 3 [ 1253.741735] Lustre: DEBUG MARKER: == sanity-sec test 47: encrypted file access semantics: rename/link ========================================================== 13:13:30 (1772907210) [ 1256.312472] bash (87864): drop_caches: 3 [ 1285.530512] LustreError: 88416:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2211us [ 1285.533718] LustreError: 88416:0:(obd_config.c:1466:process_param2_config()) Skipped 9 previous similar messages [ 1285.546804] Lustre: Mounted lustre-client [ 1285.548778] Lustre: Skipped 9 previous similar messages [ 1285.743731] bash (87864): drop_caches: 3 [ 1288.223236] LustreError: 88926:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac6673000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1288.226320] LustreError: 88926:0:(lov_obd.c:783:lov_cleanup()) Skipped 23 previous similar messages [ 1288.254218] Lustre: Unmounted lustre-client [ 1288.256210] Lustre: Skipped 11 previous similar messages [ 1288.642135] bash (87864): drop_caches: 3 [ 1289.519571] Lustre: DEBUG MARKER: == sanity-sec test 48a: encrypted file access semantics: truncate ========================================================== 13:14:06 (1772907246) [ 1290.148277] Lustre: Test dummy encryption mode enabled [ 1290.150636] Lustre: Skipped 4 previous similar messages [ 1290.837879] bash (89014): drop_caches: 3 [ 1291.675031] bash (89014): drop_caches: 3 [ 1294.429239] bash (89014): drop_caches: 3 [ 1295.306326] Lustre: DEBUG MARKER: == sanity-sec test 48b: encrypted file: concurrent truncate ========================================================== 13:14:12 (1772907252) [ 1295.943433] Lustre: DEBUG MARKER: SKIP: sanity-sec test_48b Need at least 2 clients [ 1296.527977] Lustre: DEBUG MARKER: == sanity-sec test 49: Avoid getxattr for encryption context ========================================================== 13:14:13 (1772907253) [ 1297.358426] bash (90283): drop_caches: 3 [ 1297.626179] bash (90283): drop_caches: 3 [ 1298.021802] bash (90283): drop_caches: 3 [ 1298.346364] bash (90283): drop_caches: 3 [ 1298.742625] bash (90283): drop_caches: 3 [ 1299.077216] bash (90283): drop_caches: 3 [ 1299.441933] bash (90283): drop_caches: 3 [ 1299.665424] bash (90283): drop_caches: 3 [ 1299.969134] bash (90283): drop_caches: 3 [ 1300.218241] bash (90283): drop_caches: 3 [ 1300.659857] bash (90283): drop_caches: 3 [ 1301.017067] bash (90283): drop_caches: 3 [ 1304.123102] bash (90283): drop_caches: 3 [ 1305.017410] Lustre: DEBUG MARKER: == sanity-sec test 50: DoM encrypted file ================ 13:14:22 (1772907262) [ 1305.872119] bash (91431): drop_caches: 3 [ 1306.030862] bash (91431): drop_caches: 3 [ 1306.171191] Lustre: 91697:0:(file.c:612:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 1306.274285] bash (91431): drop_caches: 3 [ 1306.438600] bash (91431): drop_caches: 3 [ 1306.658336] bash (91431): drop_caches: 3 [ 1306.808028] bash (91431): drop_caches: 3 [ 1306.941259] Lustre: 91748:0:(file.c:612:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 1306.944096] Lustre: 91748:0:(file.c:612:ll_dom_finish_open()) Skipped 1 previous similar message [ 1307.056670] bash (91431): drop_caches: 3 [ 1307.224137] bash (91431): drop_caches: 3 [ 1307.449757] bash (91431): drop_caches: 3 [ 1307.613754] bash (91431): drop_caches: 3 [ 1307.847514] bash (91431): drop_caches: 3 [ 1308.003189] bash (91431): drop_caches: 3 [ 1308.128540] Lustre: 91823:0:(file.c:612:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 1308.132053] Lustre: 91823:0:(file.c:612:ll_dom_finish_open()) Skipped 2 previous similar messages [ 1308.234553] bash (91431): drop_caches: 3 [ 1308.406445] bash (91431): drop_caches: 3 [ 1308.635323] bash (91431): drop_caches: 3 [ 1308.792848] bash (91431): drop_caches: 3 [ 1309.112563] bash (91431): drop_caches: 3 [ 1309.264969] bash (91431): drop_caches: 3 [ 1309.512344] bash (91431): drop_caches: 3 [ 1309.678765] bash (91431): drop_caches: 3 [ 1309.915045] bash (91431): drop_caches: 3 [ 1310.079635] bash (91431): drop_caches: 3 [ 1310.212876] Lustre: 91949:0:(file.c:612:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x3:0x0] with data: rc = -126 [ 1310.216894] Lustre: 91949:0:(file.c:612:ll_dom_finish_open()) Skipped 1 previous similar message [ 1310.335080] bash (91431): drop_caches: 3 [ 1310.511265] bash (91431): drop_caches: 3 [ 1310.744828] bash (91431): drop_caches: 3 [ 1310.890789] bash (91431): drop_caches: 3 [ 1313.691509] bash (91431): drop_caches: 3 [ 1314.543887] Lustre: DEBUG MARKER: == sanity-sec test 51: FS capabilities =================== 13:14:31 (1772907271) [ 1330.811352] Lustre: DEBUG MARKER: == sanity-sec test 52: Mirrored encrypted file =========== 13:14:48 (1772907288) [ 1332.551814] LustreError: 94169:0:(file.c:249:ll_close_inode_openhandle()) lustre-clilmv-ffff89aac6677800: inode [0x200000415:0x4:0x0] mdc close failed: rc = -22 [ 1334.832112] bash (93871): drop_caches: 3 [ 1335.677732] Lustre: DEBUG MARKER: == sanity-sec test 53: Mixed PAGE_SIZE clients =========== 13:14:52 (1772907292) [ 1336.281571] Lustre: DEBUG MARKER: SKIP: sanity-sec test_53 Need 64K PAGE_SIZE client [ 1336.825746] Lustre: DEBUG MARKER: == sanity-sec test 54: Encryption policies with fscrypt == 13:14:54 (1772907294) [ 1337.383718] Lustre: DEBUG MARKER: SKIP: sanity-sec test_54 This test needs fscrypt userspace tool [ 1337.978800] Lustre: DEBUG MARKER: == sanity-sec test 55: access with seteuid =============== 13:14:55 (1772907295) [ 1348.061935] Lustre: DEBUG MARKER: == sanity-sec test 56: FIEMAP on encrypted file ========== 13:15:05 (1772907305) [ 1350.969725] bash (96449): drop_caches: 3 [ 1351.995473] Lustre: DEBUG MARKER: == sanity-sec test 57: security.c/encryption.c xattr protection ========================================================== 13:15:09 (1772907309) [ 1355.220978] bash (97236): drop_caches: 3 [ 1356.119032] Lustre: DEBUG MARKER: == sanity-sec test 58: access to enc file's xattrs ======= 13:15:13 (1772907313) [ 1356.728856] Lustre: Test dummy encryption mode enabled [ 1356.730150] Lustre: Skipped 5 previous similar messages [ 1356.950519] bash (98061): drop_caches: 3 [ 1403.833460] bash (98061): drop_caches: 3 [ 1490.601031] LustreError: 109797:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac867f000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1490.605167] LustreError: 109797:0:(lov_obd.c:783:lov_cleanup()) Skipped 33 previous similar messages [ 1490.631129] Lustre: Unmounted lustre-client [ 1490.632303] Lustre: Skipped 16 previous similar messages [ 1490.802194] LustreError: 109839:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 714us [ 1490.806923] LustreError: 109839:0:(obd_config.c:1466:process_param2_config()) Skipped 17 previous similar messages [ 1490.819678] Lustre: Mounted lustre-client [ 1490.820578] Lustre: Skipped 17 previous similar messages [ 1490.977954] bash (98061): drop_caches: 3 [ 1491.753306] Lustre: DEBUG MARKER: == sanity-sec test 59a: mirror resync of encrypted files without key ========================================================== 13:17:29 (1772907449) [ 1492.401404] Lustre: Test dummy encryption mode enabled [ 1493.181345] bash (109892): drop_caches: 3 [ 1493.582132] bash (109892): drop_caches: 3 [ 1496.675777] bash (109892): drop_caches: 3 [ 1497.469067] Lustre: DEBUG MARKER: == sanity-sec test 59b: migrate/extend/split of encrypted files without key ========================================================== 13:17:34 (1772907454) [ 1498.766388] bash (110885): drop_caches: 3 [ 1499.123357] bash (110885): drop_caches: 3 [ 1500.438730] bash (110885): drop_caches: 3 [ 1500.847982] bash (110885): drop_caches: 3 [ 1502.360281] bash (110885): drop_caches: 3 [ 1502.505559] LustreError: 111666:0:(file.c:249:ll_close_inode_openhandle()) lustre-clilmv-ffff89aac7883000: inode [0x20000041d:0x2:0x0] mdc close failed: rc = -22 [ 1502.638514] bash (110885): drop_caches: 3 [ 1505.720864] bash (110885): drop_caches: 3 [ 1506.533374] Lustre: DEBUG MARKER: == sanity-sec test 59c: MDT migrate of encrypted files without key ========================================================== 13:17:43 (1772907463) [ 1507.867816] bash (112311): drop_caches: 3 [ 1508.198202] bash (112311): drop_caches: 3 [ 1510.828756] bash (112311): drop_caches: 3 [ 1511.685434] Lustre: DEBUG MARKER: == sanity-sec test 60: Subdirmount of encrypted dir ====== 13:17:48 (1772907468) [ 1512.464195] bash (113225): drop_caches: 3 [ 1513.446716] bash (113225): drop_caches: 3 [ 1516.531168] bash (113225): drop_caches: 3 [ 1517.295097] Lustre: DEBUG MARKER: == sanity-sec test 61: Nodemap enforces read-only mount == 13:17:54 (1772907474) [ 1527.338335] Lustre: lustre-MDT0001-mdc-ffff89aad8460000: connection denied by lustre-MDT0001_UUID: rc = -30 [ 1527.340521] Lustre: Skipped 1 previous similar message [ 1527.341853] LustreError: 115012:0:(lmv_obd.c:1434:lmv_statfs()) lustre-MDT0000-mdc-ffff89aad8460000: can't stat MDS #0: rc = -30 [ 1527.344662] LustreError: 115012:0:(llite_lib.c:320:ll_force_readonly()) lustre-clilmv-ffff89aad8460000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 1527.868085] LustreError: 115104:0:(llite_lib.c:320:ll_force_readonly()) lustre-clilmv-ffff89aac7883000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 1528.934583] Lustre: lustre-MDT0000-mdc-ffff89aac8808800: connection denied by lustre-MDT0000_UUID: rc = -30 [ 1528.937344] Lustre: Skipped 3 previous similar messages [ 1528.938793] LustreError: 115288:0:(lmv_obd.c:1434:lmv_statfs()) lustre-MDT0000-mdc-ffff89aac8808800: can't stat MDS #0: rc = -30 [ 1528.943143] LustreError: 115288:0:(lmv_obd.c:1434:lmv_statfs()) Skipped 1 previous similar message [ 1528.945621] LustreError: 115288:0:(llite_lib.c:320:ll_force_readonly()) lustre-clilmv-ffff89aac8808800: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 1533.983077] Lustre: DEBUG MARKER: == sanity-sec test 62: e2fsck with encrypted files ======= 13:18:11 (1772907491) [ 1593.421931] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 1601.966214] bash (115956): drop_caches: 3 [ 1602.914802] Lustre: DEBUG MARKER: == sanity-sec test 63: fid2path with encrypted files ===== 13:19:20 (1772907560) [ 1603.642222] Lustre: DEBUG MARKER: SKIP: sanity-sec test_63 This test needs fscrypt userspace tool [ 1604.256531] Lustre: DEBUG MARKER: == sanity-sec test 64a: Nodemap enforces file_perms RBAC roles ========================================================== 13:19:21 (1772907561) [ 1616.477881] Lustre: DEBUG MARKER: == sanity-sec test 64b: Nodemap enforces dne_ops RBAC roles ========================================================== 13:19:33 (1772907573) [ 1629.702733] Lustre: DEBUG MARKER: == sanity-sec test 64c: Nodemap enforces quota related RBAC roles ========================================================== 13:19:47 (1772907587) [ 1642.998392] LustreError: 122134:0:(mdc_request.c:2180:mdc_quotactl()) lustre-MDT0000-mdc-ffff89aac3e38000: ptlrpc_queue_wait failed: rc = -1 [ 1653.570850] Lustre: DEBUG MARKER: == sanity-sec test 64d: Nodemap enforces byfid_ops RBAC roles ========================================================== 13:20:11 (1772907611) [ 1665.181630] Lustre: DEBUG MARKER: == sanity-sec test 64e: Nodemap enforces chlg_ops RBAC roles ========================================================== 13:20:22 (1772907622) [ 1674.998674] LustreError: 124537:0:(mdc_changelog.c:293:chlg_load()) lustre-MDT0000-mdc-ffff89aac3e38000: fail to open changelog catalog: rc = -13 [ 1675.001810] LustreError: 124537:0:(mdc_changelog.c:293:chlg_load()) Skipped 1 previous similar message [ 1682.634533] Lustre: DEBUG MARKER: == sanity-sec test 64f: Nodemap enforces fscrypt_admin RBAC roles ========================================================== 13:20:40 (1772907640) [ 1683.195325] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64f Need fscrypt, skip fscrypt_admin role [ 1683.742926] Lustre: DEBUG MARKER: == sanity-sec test 64g: Nodemap enforces server_upcall RBAC role ========================================================== 13:20:41 (1772907641) [ 1695.673575] Lustre: DEBUG MARKER: == sanity-sec test 64h: Nodemap enforces local_admin RBAC roles ========================================================== 13:20:53 (1772907653) [ 1702.930079] LustreError: 127241:0:(mdc_request.c:2180:mdc_quotactl()) lustre-MDT0000-mdc-ffff89aac3e38000: ptlrpc_queue_wait failed: rc = -1 [ 1702.932710] LustreError: 127241:0:(mdc_request.c:2180:mdc_quotactl()) Skipped 20 previous similar messages [ 1704.517368] LustreError: 127325:0:(mdc_request.c:2180:mdc_quotactl()) lustre-MDT0000-mdc-ffff89aac3e38000: ptlrpc_queue_wait failed: rc = -1 [ 1711.723408] Lustre: DEBUG MARKER: == sanity-sec test 64i: Nodemap quota enforcement with local_admin RBAC and offsets ========================================================== 13:21:09 (1772907669) [ 1783.389123] LustreError: 132106:0:(lov_obd.c:783:lov_cleanup()) lustre-clilov-ffff89aac3e38000: lov tgt 0 not cleaned! deathrow=0, lovrc=1 [ 1783.392701] LustreError: 132106:0:(lov_obd.c:783:lov_cleanup()) Skipped 61 previous similar messages [ 1783.419199] Lustre: Unmounted lustre-client [ 1783.420284] Lustre: Skipped 30 previous similar messages [ 1785.648348] LustreError: 132242:0:(obd_config.c:1466:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1552us [ 1785.652156] LustreError: 132242:0:(obd_config.c:1466:process_param2_config()) Skipped 30 previous similar messages [ 1785.664152] Lustre: Mounted lustre-client [ 1785.665620] Lustre: Skipped 30 previous similar messages [ 1786.616303] Lustre: DEBUG MARKER: == sanity-sec test 65: lfs find -printf %La and --attrs support ========================================================== 13:22:24 (1772907744) [ 1787.174327] Lustre: Test dummy encryption mode enabled [ 1787.175741] Lustre: Skipped 10 previous similar messages [ 1790.115902] bash (132310): drop_caches: 3 [ 1790.934406] Lustre: DEBUG MARKER: == sanity-sec test 68: all config logs are processed ===== 13:22:28 (1772907748) [ 1791.442161] LustreError: 2400:0:(niobuf.c:881:ptl_send_rpc()) cfs_fail_timeout id 51d sleeping for 20000ms [ 1796.576511] LustreError: 133538:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.204.104@tcp: failed processing log, type 1: rc = -110 [ 1811.520118] LustreError: 2400:0:(niobuf.c:881:ptl_send_rpc()) cfs_fail_timeout id 51d awake [ 1817.228297] Lustre: DEBUG MARKER: == sanity-sec test 69: check upcall incorrect values ===== 13:22:54 (1772907774) [ 1821.186138] Lustre: DEBUG MARKER: == sanity-sec test 70: targets have local copy of sptlrpc llog ========================================================== 13:22:58 (1772907778) [ 1821.747353] Lustre: DEBUG MARKER: SKIP: sanity-sec test_70 need shared key feature for this test [ 1822.370431] Lustre: DEBUG MARKER: == sanity-sec test 71: encryption does not remove project flag ========================================================== 13:22:59 (1772907779) [ 1822.908624] Lustre: DEBUG MARKER: SKIP: sanity-sec test_71 Need fscrypt [ 1823.498237] Lustre: DEBUG MARKER: == sanity-sec test 72a: dynamic nodemap properties on OSS ========================================================== 13:23:00 (1772907780) [ 1853.448959] Lustre: DEBUG MARKER: == sanity-sec test 72b: dynamic nodemap properties on MDS ========================================================== 13:23:30 (1772907810) [ 1883.151792] Lustre: DEBUG MARKER: == sanity-sec test 72c: child_raise_privileges nodemap property ========================================================== 13:24:00 (1772907840) [ 1898.525184] Lustre: DEBUG MARKER: == sanity-sec test 72d: fileset inheritance for dynamic nodemap ========================================================== 13:24:15 (1772907855) [ 1919.228847] Lustre: DEBUG MARKER: == sanity-sec test 72e: dynamic nodemap reclassify ======= 13:24:36 (1772907876) [ 1932.419120] Lustre: DEBUG MARKER: == sanity-sec test 72f: fileset_modify on dynamic nodemap ========================================================== 13:24:49 (1772907889) [ 1953.143977] Lustre: DEBUG MARKER: == sanity-sec test 73: encrypted names in changelogs ===== 13:25:10 (1772907910) [ 1953.755857] Lustre: DEBUG MARKER: SKIP: sanity-sec test_73 Need fscrypt [ 1954.294359] Lustre: DEBUG MARKER: == sanity-sec test 74: Set nodemap deny_mount flag ======= 13:25:11 (1772907911) [ 1961.922274] LustreError: 144162:0:(llite_lib.c:505:client_common_fill_super()) lustre-clilmv-ffff89aac867d000: cannot mds_connect: rc = -1 [ 1961.971130] LustreError: 144162:0:(super25.c:186:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 1967.873554] Lustre: DEBUG MARKER: == sanity-sec test 75: check uid/gid/projid are set on OST and MDT for various RPCs ========================================================== 13:25:25 (1772907925) [ 1988.920902] Lustre: DEBUG MARKER: == sanity-sec test 75a: test resource fs IDs against nodemap offset ========================================================== 13:25:46 (1772907946) [ 1989.978235] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75a need at least two clients [ 1990.538246] Lustre: DEBUG MARKER: == sanity-sec test 75b: test resource ID repair ========== 13:25:47 (1772907947) [ 2049.201146] bash (148444): drop_caches: 3 [ 2055.291496] bash (148797): drop_caches: 3 [ 2074.285898] Lustre: DEBUG MARKER: == sanity-sec test 76: suppgroups and gid mapping ======== 13:27:11 (1772908031) [ 2086.292867] Lustre: DEBUG MARKER: == sanity-sec test 77: root offsetting =================== 13:27:23 (1772908043) [ 2099.075722] Lustre: DEBUG MARKER: == sanity-sec test 78: nodemap stats ===================== 13:27:36 (1772908056) [ 2110.691370] Lustre: DEBUG MARKER: == sanity-sec test 79: ssk for nodemap identification ==== 13:27:48 (1772908068) [ 2111.202122] Lustre: DEBUG MARKER: SKIP: sanity-sec test_79 Need shared key feature for this test [ 2111.780340] Lustre: DEBUG MARKER: == sanity-sec test 81a: nodemap ban list ================= 13:27:49 (1772908069) [ 2112.317677] Lustre: DEBUG MARKER: test_81a 4917 [ 2119.003652] Lustre: This client was banned by administrative request for file system lustre. All requests will get Operation not permitted. [ 2119.006244] LustreError: 154077:0:(file.c:6162:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 2130.809373] LustreError: 154652:0:(file.c:6162:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 2130.812226] LustreError: 154652:0:(file.c:6162:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 2135.056379] LustreError: 154878:0:(lmv_obd.c:1434:lmv_statfs()) lustre-MDT0000-mdc-ffff89aac644e000: can't stat MDS #0: rc = -1 [ 2135.085576] LustreError: 154878:0:(super25.c:186:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 2138.380530] LustreError: 155123:0:(file.c:6162:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 2138.384903] LustreError: 155123:0:(file.c:6162:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 2138.687171] LustreError: 155161:0:(super25.c:186:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 2145.057505] Lustre: DEBUG MARKER: == sanity-sec test 81b: banned client does not block other ========================================================== 13:28:22 (1772908102) [ 2145.613030] Lustre: DEBUG MARKER: SKIP: sanity-sec test_81b Need 2 clients [ 2146.176339] Lustre: DEBUG MARKER: == sanity-sec test 82: export lock revoked after nodemap change ========================================================== 13:28:23 (1772908103) [ 2166.457045] Lustre: DEBUG MARKER: == sanity-sec test 83: Suppgids for cross-MDT ops ======== 13:28:43 (1772908123) [ 2170.179532] Lustre: DEBUG MARKER: == sanity-sec test 84: do not squash trusted ids ========= 13:28:47 (1772908127) [ 2181.658774] Lustre: DEBUG MARKER: == sanity-sec test 85: forbid squashing to UID/GID 0 ===== 13:28:59 (1772908139) [ 2193.264362] Lustre: DEBUG MARKER: == sanity-sec test 100: SSK automatic prime generation when mounting with server key ========================================================== 13:29:10 (1772908150) [ 2193.747941] Lustre: DEBUG MARKER: SKIP: sanity-sec test_100 Need shared key feature for this test [ 2194.291804] Lustre: DEBUG MARKER: == sanity-sec test 101: lgss_sk -a and -l support for ascii-encoded SSK keys ========================================================== 13:29:11 (1772908151) [ 2194.766224] Lustre: DEBUG MARKER: SKIP: sanity-sec test_101 Need shared key feature for this test [ 2195.276917] Lustre: DEBUG MARKER: == sanity-sec test 102: SSK automatic key loading from mount point ========================================================== 13:29:12 (1772908152) [ 2195.844963] Lustre: DEBUG MARKER: SKIP: sanity-sec test_102 Need shared key feature for this test [ 2196.377372] Lustre: DEBUG MARKER: cleanup: ====================================================== [ 2196.885229] Lustre: DEBUG MARKER: == sanity-sec test complete, duration 2055 sec =========== 13:29:14 (1772908154) [ 2197.418573] Lustre: DEBUG MARKER: === sanity-sec: start cleanup 13:29:14 (1772908154) === [ 2199.239253] Lustre: DEBUG MARKER: === sanity-sec: finish cleanup 13:29:16 (1772908156) === [ 2239.261630] Key type lgssc unregistered [ 2239.380452] LNet: 162957:0:(lib-ptl.c:967:lnet_clear_lazy_portal()) Active lazy portal 0 on exit [ 2239.382643] LNetError: 162957:0:(acceptor.c:252:lnet_acceptor_remove_socket()) Interface ens2 not found [ 2239.389815] LNet: Removed LNI 192.168.204.4@tcp [ 2239.670109] Key type .llcrypt unregistered [ 2239.671253] Key type ._llcrypt unregistered