[ 0.000000] Linux version 4.18.0rh8.10-debug (green@maintenance) (gcc version 8.5.0 20210514 (Red Hat 8.5.0-26) (GCC)) #2 SMP Mon Jul 14 01:24:22 EDT 2025 [ 0.000000] Command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.000000] signal: max sigframe size: 1776 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffd9fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bffda000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000146dfffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-10.fc44 06/10/2025 [ 0.000000] Hypervisor detected: KVM [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: using sched offset of 452836296 cycles [ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.000000] tsc: Detected 2399.998 MHz processor [ 0.000000] last_pfn = 0x146e00 max_arch_pfn = 0x400000000 [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] last_pfn = 0xbffda max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f54d0-0x000f54df] [ 0.000000] RAMDISK: [mem 0xbcc64000-0xbffcffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F52F0 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x00000000BFFE2464 000034 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x00000000BFFE2300 000074 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x00000000BFFE0040 0022C0 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACS 0x00000000BFFE0000 000040 [ 0.000000] ACPI: APIC 0x00000000BFFE2374 000090 (v03 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x00000000BFFE2404 000038 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: WAET 0x00000000BFFE243C 000028 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: Reserving FACP table memory at [mem 0xbffe2300-0xbffe2373] [ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xbffe0040-0xbffe22ff] [ 0.000000] ACPI: Reserving FACS table memory at [mem 0xbffe0000-0xbffe003f] [ 0.000000] ACPI: Reserving APIC table memory at [mem 0xbffe2374-0xbffe2403] [ 0.000000] ACPI: Reserving HPET table memory at [mem 0xbffe2404-0xbffe243b] [ 0.000000] ACPI: Reserving WAET table memory at [mem 0xbffe243c-0xbffe2463] [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000146dfffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x1465a3000-0x1465cdfff] [ 0.000000] Reserving 256MB of memory at 2752MB for crashkernel (System RAM: 4205MB) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000bffd9fff] [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Zeroed struct page in unavailable ranges: 4744 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000146dfffff] [ 0.000000] ACPI: PM-Timer IO Port: 0x608 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] TSC deadline timer available [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] kvm-guest: KVM setup pv remote TLB flush [ 0.000000] kvm-guest: setup PV sched yield [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbffda000-0xbfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfeffbfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeffc000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] [mem 0xc0000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.000000] kvm-guest: PV spinlocks enabled [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1059618 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] Specific versions of hardware are certified with Red Hat Enterprise Linux 8. Please see the list of hardware certified with Red Hat Enterprise Linux 8 at https://catalog.redhat.com. [ 0.000000] audit: disabled (until reboot) [ 0.000000] software IO TLB: area num 4. [ 0.000000] Memory: 2829700K/4306400K available (18435K kernel code, 11221K rwdata, 7248K rodata, 2908K init, 18040K bss, 524580K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] ftrace: allocating 41240 entries in 162 pages [ 0.000000] ftrace: allocated 162 pages with 3 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.000000] rcu: RCU callback double-/use-after-free debug enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x622/0x9a8 with crng_init=0 [ 0.001000] Console: colour *CGA 80x25 [ 0.001000] printk: console [ttyS1] enabled [ 0.001000] ACPI: Core revision 20220331 [ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.001009] APIC: Switch to symmetric I/O mode setup [ 0.003083] x2apic enabled [ 0.004011] Switched APIC routing to physical x2apic. [ 0.005012] kvm-guest: setup PV IPIs [ 0.007487] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.008000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 0.008021] Calibrating delay loop (skipped) preset value.. 4799.99 BogoMIPS (lpj=2399998) [ 0.009013] pid_max: default: 32768 minimum: 301 [ 0.010143] LSM: Security Framework initializing [ 0.011057] Yama: becoming mindful. [ 0.012041] SELinux: Initializing. [ 0.013110] *** VALIDATE selinux *** [ 0.021793] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc) [ 0.025895] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc) [ 0.026183] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.027146] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.028126] *** VALIDATE tmpfs *** [ 0.029472] *** VALIDATE proc *** [ 0.030265] *** VALIDATE cgroup *** [ 0.031009] *** VALIDATE cgroup2 *** [ 0.032237] x86/cpu: User Mode Instruction Prevention (UMIP) activated [ 0.033163] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.034008] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.035031] Spectre V2 : User space: Vulnerable [ 0.036013] Speculative Store Bypass: Vulnerable [ 0.039117] debug: unmapping init [mem 0xffffffff9f459000-0xffffffff9f460fff] [ 0.042187] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz (family: 0x6, model: 0x3e, stepping: 0x4) [ 0.043759] Performance Events: IvyBridge events, full-width counters, Intel PMU driver. [ 0.044021] ... version: 2 [ 0.045015] ... bit width: 48 [ 0.046014] ... generic registers: 4 [ 0.047013] ... value mask: 0000ffffffffffff [ 0.048017] ... max period: 00007fffffffffff [ 0.049016] ... fixed-purpose events: 3 [ 0.050019] ... event mask: 000000070000000f [ 0.052250] rcu: Hierarchical SRCU implementation. [ 0.054322] smp: Bringing up secondary CPUs ... [ 0.055554] x86: Booting SMP configuration: [ 0.056029] .... node #0, CPUs: #1 #2 #3 [ 0.059484] smp: Brought up 1 node, 4 CPUs [ 0.061022] smpboot: Max logical packages: 1 [ 0.062021] smpboot: Total of 4 processors activated (19199.98 BogoMIPS) [ 0.257320] node 0 deferred pages initialised in 193ms [ 0.261169] devtmpfs: initialized [ 0.262245] x86/mm: Memory block size: 128MB [ 0.264351] gcov: version magic: 0x41383552 [ 0.265632] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.269121] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc) [ 0.271436] pinctrl core: initialized pinctrl subsystem [ 0.273178] [ 0.273555] ************************************************************* [ 0.275014] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.277011] ** ** [ 0.278011] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.280016] ** ** [ 0.281009] ** This means that this kernel is built to expose internal ** [ 0.283022] ** IOMMU data structures, which may compromise security on ** [ 0.285017] ** your system. ** [ 0.287014] ** ** [ 0.289016] ** If you see this message and you are not debugging the ** [ 0.290013] ** kernel, report this immediately to your vendor! ** [ 0.292013] ** ** [ 0.294018] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.295029] ************************************************************* [ 0.297849] NET: Registered protocol family 16 [ 0.300533] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.303063] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.307070] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.311014] cpuidle: using governor menu [ 0.312507] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.315576] PCI: Using configuration type 1 for base access [ 0.317133] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on [ 0.327081] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.329037] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.331172] cryptd: max_cpu_qlen set to 1000 [ 0.335024] ACPI: Added _OSI(Module Device) [ 0.337025] ACPI: Added _OSI(Processor Device) [ 0.339026] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.340021] ACPI: Added _OSI(Processor Aggregator Device) [ 0.345330] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 0.352369] ACPI: Interpreter enabled [ 0.354070] ACPI: PM: (supports S0 S3 S4 S5) [ 0.356015] ACPI: Using IOAPIC for interrupt routing [ 0.357122] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.361392] ACPI: Enabled 2 GPEs in block 00 to 0F [ 0.373655] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.376061] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI HPX-Type3] [ 0.379021] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI] [ 0.382098] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.388721] acpiphp: Slot [2] registered [ 0.390196] acpiphp: Slot [5] registered [ 0.392179] acpiphp: Slot [6] registered [ 0.393129] acpiphp: Slot [3] registered [ 0.394102] acpiphp: Slot [4] registered [ 0.395065] acpiphp: Slot [7] registered [ 0.397104] acpiphp: Slot [8] registered [ 0.398143] acpiphp: Slot [9] registered [ 0.400141] acpiphp: Slot [10] registered [ 0.401112] acpiphp: Slot [11] registered [ 0.403135] acpiphp: Slot [12] registered [ 0.405116] acpiphp: Slot [13] registered [ 0.406087] acpiphp: Slot [14] registered [ 0.407067] acpiphp: Slot [15] registered [ 0.408182] acpiphp: Slot [16] registered [ 0.410125] acpiphp: Slot [17] registered [ 0.412155] acpiphp: Slot [18] registered [ 0.413122] acpiphp: Slot [19] registered [ 0.415124] acpiphp: Slot [20] registered [ 0.416120] acpiphp: Slot [21] registered [ 0.418104] acpiphp: Slot [22] registered [ 0.419097] acpiphp: Slot [23] registered [ 0.420072] acpiphp: Slot [24] registered [ 0.422082] acpiphp: Slot [25] registered [ 0.423000] acpiphp: Slot [26] registered [ 0.424084] acpiphp: Slot [27] registered [ 0.425068] acpiphp: Slot [28] registered [ 0.426122] acpiphp: Slot [29] registered [ 0.427108] acpiphp: Slot [30] registered [ 0.428086] acpiphp: Slot [31] registered [ 0.430058] PCI host bridge to bus 0000:00 [ 0.431046] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.434039] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.437037] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.441038] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.444037] pci_bus 0000:00: root bus resource [mem 0xe0000000000-0xe007fffffff window] [ 0.446031] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.447158] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.449333] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.453359] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.460949] pci 0000:00:01.1: reg 0x20: [io 0xc120-0xc12f] [ 0.466000] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.469020] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.471017] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.473018] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.475778] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.478820] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI [ 0.482052] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB [ 0.485501] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 [ 0.489981] pci 0000:00:02.0: reg 0x10: [io 0xc100-0xc11f] [ 0.499995] pci 0000:00:02.0: reg 0x20: [mem 0xe0000000000-0xe0000003fff 64bit pref] [ 0.505020] pci 0000:00:02.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref] [ 0.510105] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.517025] pci 0000:00:05.0: reg 0x10: [io 0xc000-0xc07f] [ 0.524028] pci 0000:00:05.0: reg 0x14: [mem 0xfebc0000-0xfebc0fff] [ 0.541031] pci 0000:00:05.0: reg 0x20: [mem 0xe0000004000-0xe0000007fff 64bit pref] [ 0.550879] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.559015] pci 0000:00:06.0: reg 0x10: [io 0xc080-0xc0ff] [ 0.566016] pci 0000:00:06.0: reg 0x14: [mem 0xfebc1000-0xfebc1fff] [ 0.582016] pci 0000:00:06.0: reg 0x20: [mem 0xe0000008000-0xe000000bfff 64bit pref] [ 0.592196] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.594420] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 0.596430] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 0.599425] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 0.601297] ACPI: PCI: Interrupt link LNKS configured for IRQ 9 [ 0.605142] iommu: Default domain type: Passthrough [ 0.607373] SCSI subsystem initialized [ 0.609250] ACPI: bus type USB registered [ 0.610110] usbcore: registered new interface driver usbfs [ 0.612132] usbcore: registered new interface driver hub [ 0.614104] usbcore: registered new device driver usb [ 0.616181] pps_core: LinuxPPS API ver. 1 registered [ 0.617015] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.620092] PTP clock support registered [ 0.622127] EDAC MC: Ver: 3.0.0 [ 0.623357] PCI: Using ACPI for IRQ routing [ 0.624708] NetLabel: Initializing [ 0.625013] NetLabel: domain hash size = 128 [ 0.626010] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.627088] NetLabel: unlabeled traffic allowed by default [ 0.629167] vgaarb: loaded [ 0.631355] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.633027] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.639419] clocksource: Switched to clocksource kvm-clock [ 0.747126] VFS: Disk quotas dquot_6.6.0 [ 0.748697] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.751233] *** VALIDATE ramfs *** [ 0.752736] *** VALIDATE hugetlbfs *** [ 0.754240] pnp: PnP ACPI init [ 0.756441] pnp: PnP ACPI: found 6 devices [ 0.775298] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.778519] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.780378] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.782600] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.785374] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.787878] pci_bus 0000:00: resource 8 [mem 0xe0000000000-0xe007fffffff window] [ 0.790543] NET: Registered protocol family 2 [ 0.793368] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc) [ 0.798305] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, vmalloc) [ 0.802395] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc) [ 0.807865] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc) [ 0.812841] TCP: Hash tables configured (established 65536 bind 65536) [ 0.816408] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, vmalloc) [ 0.820285] UDP hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.823518] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.827259] NET: Registered protocol family 1 [ 0.830436] RPC: Registered named UNIX socket transport module. [ 0.832833] RPC: Registered udp transport module. [ 0.834679] RPC: Registered tcp transport module. [ 0.836468] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.839323] NET: Registered protocol family 44 [ 0.840982] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.843279] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.845507] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.847799] PCI: CLS 0 bytes, default 64 [ 0.849289] Unpacking initramfs... [ 2.238914] debug: unmapping init [mem 0xffff9b967cc64000-0xffff9b967ffcffff] [ 2.243194] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 2.245822] software IO TLB: mapped [mem 0x00000000a8000000-0x00000000ac000000] (64MB) [ 2.248963] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 2.780245] Initialise system trusted keyrings [ 2.781979] Key type blacklist registered [ 2.785379] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 2.796622] zbud: loaded [ 2.800562] *** VALIDATE nfs *** [ 2.802051] *** VALIDATE nfs4 *** [ 2.803611] pstore: using deflate compression [ 2.807104] Platform Keyring initialized [ 2.928458] NET: Registered protocol family 38 [ 2.930375] Key type asymmetric registered [ 2.931878] Asymmetric key parser 'x509' registered [ 2.933635] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.936488] io scheduler mq-deadline registered [ 2.938640] io scheduler kyber registered [ 2.940607] io scheduler bfq registered [ 2.942789] atomic64_test: passed for x86-64 platform with CX8 and with SSE [ 2.945510] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.947600] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 2.949909] ACPI: Power Button [PWRF] [ 2.957623] ACPI: \_SB_.LNKB: Enabled at IRQ 10 [ 2.963100] ACPI: \_SB_.LNKA: Enabled at IRQ 11 [ 2.973912] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.003482] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 3.034064] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 3.040125] Non-volatile memory driver v1.3 [ 3.042120] Linux agpgart interface v0.103 [ 3.070654] virtio_blk virtio1: [vda] 146144 512-byte logical blocks (74.8 MB/71.4 MiB) [ 3.072667] vda: detected capacity change from 0 to 74825728 [ 3.091719] virtio_blk virtio2: [vdb] 2097152 512-byte logical blocks (1.07 GB/1.00 GiB) [ 3.094869] vdb: detected capacity change from 0 to 1073741824 [ 3.103623] libphy: Fixed MDIO Bus: probed [ 3.111386] usbcore: registered new interface driver usbserial_generic [ 3.114393] usbserial: USB Serial support registered for generic [ 3.116836] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 3.121889] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.123882] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.126436] mousedev: PS/2 mouse device common for all mice [ 3.130500] rtc_cmos 00:05: RTC can wake from S4 [ 3.133051] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 3.133647] rtc_cmos 00:05: registered as rtc0 [ 3.139267] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs [ 3.140118] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input4 [ 3.143456] intel_pstate: CPU model not supported [ 3.152410] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input3 [ 3.152813] hid: raw HID events driver (C) Jiri Kosina [ 3.158568] usbcore: registered new interface driver usbhid [ 3.160995] usbhid: USB HID core driver [ 3.162899] drop_monitor: Initializing network drop monitor service [ 3.165688] Initializing XFRM netlink socket [ 3.168220] NET: Registered protocol family 10 [ 3.171649] Segment Routing with IPv6 [ 3.173252] NET: Registered protocol family 17 [ 3.175475] mpls_gso: MPLS GSO support [ 3.183126] RAS: Correctable Errors collector initialized. [ 3.185248] AVX version of gcm_enc/dec engaged. [ 3.187058] AES CTR mode by8 optimization enabled [ 3.286148] sched_clock: Marking stable (3286086042, 0)->(4193614414, -907528372) [ 3.290405] registered taskstats version 1 [ 3.293138] Loading compiled-in X.509 certificates [ 3.295905] zswap: loaded using pool lzo/zbud [ 3.325195] Key type big_key registered [ 3.346131] Key type encrypted registered [ 3.347521] ima: No TPM chip found, activating TPM-bypass! [ 3.349593] ima: Allocated hash algorithm: sha1 [ 3.351458] ima: No architecture policies found [ 3.353198] evm: Initialising EVM extended attributes: [ 3.355157] evm: security.selinux [ 3.356225] evm: security.ima [ 3.357178] evm: security.capability [ 3.358548] evm: HMAC attrs: 0x1 [ 3.361531] rtc_cmos 00:05: setting system clock to 2026-08-24 19:43:43 UTC (1787600623) [ 3.367413] debug: unmapping init [mem 0xffffffffa0403000-0xffffffffa05fffff] [ 3.370971] debug: unmapping init [mem 0xffffffff9f182000-0xffffffff9f458fff] [ 3.381112] Write protecting the kernel read-only data: 28672k [ 3.386511] debug: unmapping init [mem 0xffffffff9d803000-0xffffffff9d9fffff] [ 3.389395] debug: unmapping init [mem 0xffffffff9e114000-0xffffffff9e1fffff] [ 3.420398] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 3.426924] systemd[1]: Detected virtualization kvm. [ 3.428522] systemd[1]: Detected architecture x86-64. [ 3.429863] systemd[1]: Running in initial RAM disk. Welcome to Rocky Linux 8.10 (Green Obsidian) dracut-049-233.git20240115.el8 (Initramfs)! [ 3.463104] systemd[1]: No hostname configured. [ 3.464853] systemd[1]: Set hostname to . [ 3.466945] random: systemd: uninitialized urandom read (16 bytes read) [ 3.469665] systemd[1]: Initializing machine ID from random generator. [ 3.631871] random: systemd: uninitialized urandom read (16 bytes read) [ 3.634877] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 3.639490] random: systemd: uninitialized urandom read (16 bytes read) [ 3.642441] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 3.645888] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ OK ] Reached target Local File Systems. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Listening on Journal Socket. Starting Create Volatile Files and Directories... [ OK ] Started Memstrack Anylazing Service. [ OK ] Reached target Slices. Starting Create list of required st…ce nodes for the current kernel... Starting Apply Kernel Variables... [ OK ] Reached target Timers. [ OK ] Reached target Local Encrypted Volumes. Starting Setup Virtual Console... [ OK ] Reached target Paths. [ OK ] Reached target Initrd Root Device. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Reached target Sockets. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Apply Kernel Variables. [ OK ] Started Setup Virtual Console. Starting dracut cmdline hook... Starting Create Static Device Nodes in /dev... [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started dracut cmdline hook. Starting dracut pre-udev hook... [ 4.222827] device-mapper: uevent: version 1.0.3 [ 4.224376] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ OK ] Started dracut pre-udev hook. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook.[ 4.584726] random: fast init done Starting udev Coldplug all Devices... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting dracut initqueue hook... [ 4.967841] virtio_net virtio0 ens2: renamed from eth0 [ 5.256672] scsi host0: ata_piix [ 5.290363] scsi host1: ata_piix [ 5.292405] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc120 irq 14 [ 5.294979] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc128 irq 15 [ 8.930677] dracut-initqueue[576]: RTNETLINK answers: File exists [ 9.863875] random: crng init done [ 9.865332] random: 7 urandom warning(s) missed due to ratelimiting Starting nbd nbd0... [ OK ] Started nbd nbd0. [ OK ] Started dracut initqueue hook. Mounting /sysroot... [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ 10.438095] EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /sysroot. [ OK ] Reached target Initrd Root File System. Starting Reload Configuration from the Real Root... [ OK ] Started Reload Configuration from the Real Root. [ OK ] Reached target Initrd File Systems. [ OK ] Reached target Initrd Default Target. Starting dracut pre-pivot and cleanup hook... [ OK ] Started dracut pre-pivot and cleanup hook. Starting Cleaning Up and Shutting Down Daemons... Stopping Hardware RNG Entropy Gatherer Daemon... [ OK ] Stopped target Timers. [ OK ] Stopped dracut pre-pivot and cleanup hook. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped dracut initqueue hook. [ OK ] Stopped target Initrd Default Target. [ OK ] Stopped target Initrd Root Device. [ OK ] Stopped Hardware RNG Entropy Gatherer Daemon. [ OK ] Stopped target Basic System. [ OK ] Stopped target Sockets. [ OK ] Stopped target Paths. [ OK ] Stopped target Slices. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Swap. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped udev Coldplug all Devices. [ OK ] Stopped dracut pre-trigger hook. Stopping udev Kernel Device Manager... [ OK ] Started Cleaning Up and Shutting Down Daemons. [ OK ] Stopped udev Kernel Device Manager. [ OK ] Stopped dracut pre-udev hook. [ OK ] Stopped dracut cmdline hook. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create list of required sta…vice nodes for the current kernel. [ OK ] Closed udev Control Socket. [ OK ] Closed udev Kernel Socket. Starting Cleanup udevd DB... [ OK ] Started Cleanup udevd DB. [ OK ] Reached target Switch Root. Starting Switch Root... [ 11.595295] printk: systemd: 25 output lines suppressed due to ratelimiting [ 11.869416] SELinux: Disabled at runtime. [ 11.932466] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 11.941212] systemd[1]: Detected virtualization kvm. [ 11.943319] systemd[1]: Detected architecture x86-64. Welcome to Rocky Linux 8.10 (Green Obsidian)! [ 12.376178] systemd[1]: initrd-switch-root.service: Succeeded. [ 12.379340] systemd[1]: Stopped Switch Root. [ OK ] Stopped Switch Root. [ 12.384304] systemd[1]: systemd-journald.service: Service has no hold-off time (RestartSec=0), scheduling restart. [ 12.389372] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1. [ 12.393058] systemd[1]: Stopped Journal Service. [ OK ] Stopped Journal Service. [ 12.400686] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.410512] systemd[1]: Activating swap /dev/disk/by-label/SWAP... Activating swap /dev/disk/by-label/SWAP... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... [ OK ] Reached target rpc_pipefs.target. Mounting POSIX Message Queue File System... [ 12.455967] Adding 1048572k swap on /dev/vdb. Priority:-2 extents:1 across:1048572k FS [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target RPC Port Mapper. [ OK ] Created slice system-getty.slice. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Created slice system-sshd\x2dkeygen.slice. [ OK ] Listening on Process Core Dump Socket. [ OK ] Stopped target Switch Root. [ OK ] Stopped target Initrd Root File System. [ OK ] Stopped target Initrd File Systems. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... [FAILED] Failed to set up automount Arbitrar…rmats File System Automount Point. See 'systemctl status proc-sys-fs-binfmt_misc.automount' for details. Mounting Kernel Debug File System... [ OK ] Listening on initctl Compatibility Named Pipe. Starting Apply Kernel Variables... Starting Remount Root and Kernel File Systems... [ OK ] Started Journal Service. [ OK ] Activated swap /dev/disk/by-label/SWAP. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. Starting Configure read-only root support... Starting Create Static Device Nodes in /dev... [ OK ] Reached target Swap. Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /home/green/git/lustre-release... Mounting /mnt... [ OK ] Mounted /mnt. [ 12.953244] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ OK ] Mounted /home/green/git/lustre-release. [ OK ] Started udev Kernel Device Manager. [ 13.223557] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0 [ 13.272830] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 13.336555] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer [ 13.352099] EDAC sbridge: Ver: 1.1.2 [ 15.348458] Key type dns_resolver registered [ 16.002591] NFS: Registering the id_resolver key type [ 16.010598] Key type id_resolver registered [ 16.016864] Key type id_legacy registered [ OK ] Started Configure read-only root support. [ OK ] Reached target Local File Systems. Starting Mark the need to relabel after reboot... Starting Rebuild Dynamic Linker Cache... Starting Create Volatile Files and Directories... Starting Load/Save Random Seed... [ OK ] Started Mark the need to relabel after reboot. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting RPC Bind... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC Bind. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started dnf makecache --timer. [ OK ] Started daily update of the root trust anchor for DNSSEC. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Restore /run/initramfs on shutdown... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting Network Manager... [ OK ] Reached target sshd-keygen.target. Starting Login Service... [ OK ] Started irqbalance daemon. [ OK ] Started Restore /run/initramfs on shutdown. [ OK ] Started Network Manager. Starting Network Manager Wait Online... [ OK ] Reached target Network. Starting OpenSSH server daemon... Starting Dynamic System Tuning Daemon... Starting GSSAPI Proxy Daemon... [ OK ] Started Login Service. Starting Hostname Service... [ OK ] Started OpenSSH server daemon. [ OK ] Started GSSAPI Proxy Daemon. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS1. [ OK ] Started Command Scheduler. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting Crash recovery kernel arming... Starting Notify NFS peers of a restart... Starting System Logging Service... [ OK ] Started Notify NFS peers of a restart. [ OK ] Started System Logging Service. Starting Authorization Manager... Rocky Linux 8.10 (Green Obsidian) Kernel 4.18.0rh8.10-debug on an x86_64 oleg224-client login: [ 87.990302] libcfs: loading out-of-tree module taints kernel. [ 88.256656] Key type ._llcrypt registered [ 88.266726] Key type .llcrypt registered [ 88.889981] libcfs: HW NUMA nodes: 1, HW CPU cores: 4, npartitions: 2 [ 88.922727] alg: No test for adler32 (adler32-zlib) [ 90.475367] Lustre: Lustre: Build Version: 2.17.57_82_gfc0532e [ 91.432044] LNet: Added LNI 192.168.202.24@tcp [8/256/0/180] [ 93.289970] Key type lgssc registered [ 95.874750] Lustre: Echo OBD driver; http://www.lustre.org/ [ 148.893007] hrtimer: interrupt took 6253025 ns [ 245.894650] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 250.754843] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 268.803276] Lustre: DEBUG MARKER: oleg224-client.virtnet: executing check_logdir /tmp/testlogs/ [ 271.328368] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 23s idle [ 277.636480] Lustre: DEBUG MARKER: oleg224-client.virtnet: executing yml_node [ 282.551136] Lustre: DEBUG MARKER: Client: 2.17.57.82 [ 285.700935] Lustre: DEBUG MARKER: MDS: 2.17.57.82 [ 288.773243] Lustre: DEBUG MARKER: OSS: 2.17.57.82 [ 290.271965] Lustre: DEBUG MARKER: -----============= acceptance-small: sanity-sec ============----- Mon Aug 24 15:48:29 EDT 2026 [ 311.174651] Lustre: DEBUG MARKER: excepting tests: 27 [ 312.719245] Lustre: DEBUG MARKER: skipping tests SLOW=no: 26 [ 314.967064] Lustre: DEBUG MARKER: === sanity-sec: start setup 15:48:53 (1787600933) === [ 321.605147] Lustre: DEBUG MARKER: oleg224-client.virtnet: executing check_config_client /mnt/lustre [ 345.619823] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 359.459264] Lustre: DEBUG MARKER: === sanity-sec: finish setup 15:49:37 (1787600977) === [ 367.689872] Lustre: DEBUG MARKER: == sanity-sec test 0: uid permission ======================================================================================= 15:49:45 (1787600985) [ 378.467419] Lustre: DEBUG MARKER: == sanity-sec test 1: setuid/gid ======================================================================================= 15:49:56 (1787600996) [ 380.586642] Lustre: DEBUG MARKER: SKIP: sanity-sec test_1 without GSS support. [ 383.046824] Lustre: DEBUG MARKER: == sanity-sec test 4: set supplementary group ========================================================================= 15:50:01 (1787601001) [ 389.092176] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 20s idle [ 389.100145] Lustre: Skipped 1 previous similar message [ 395.536971] Lustre: DEBUG MARKER: == sanity-sec test 5: Test l_getidentity with a nonexistent user on the MDT ========================================================== 15:50:14 (1787601014) [ 420.648655] Lustre: DEBUG MARKER: == sanity-sec test 7: nodemap create and delete ========== 15:50:38 (1787601038) [ 456.952898] Lustre: DEBUG MARKER: == sanity-sec test 8: nodemap reject duplicates ========== 15:51:15 (1787601075) [ 506.486622] Lustre: DEBUG MARKER: == sanity-sec test 9: nodemap range add ================== 15:52:05 (1787601125) [ 554.457223] Lustre: DEBUG MARKER: == sanity-sec test 10a: nodemap reject duplicate ranges == 15:52:53 (1787601173) [ 609.602094] Lustre: DEBUG MARKER: == sanity-sec test 10b: delete range from the correct nodemap ========================================================== 15:53:48 (1787601228) [ 626.028024] Lustre: DEBUG MARKER: == sanity-sec test 10c: verfify contiguous range support ========================================================== 15:54:04 (1787601244) [ 638.766221] Lustre: DEBUG MARKER: == sanity-sec test 10d: verfify nodemap range format '*@' support ========================================================== 15:54:17 (1787601257) [ 652.180670] Lustre: DEBUG MARKER: == sanity-sec test 11: nodemap modify ==================== 15:54:30 (1787601270) [ 698.405462] Lustre: DEBUG MARKER: == sanity-sec test 12: nodemap set squash ids ============ 15:55:16 (1787601316) [ 743.700758] Lustre: DEBUG MARKER: == sanity-sec test 13: test nids ========================= 15:56:02 (1787601362) [ 794.503682] Lustre: DEBUG MARKER: == sanity-sec test 14: test default nodemap nid lookup === 15:56:52 (1787601412) [ 844.682386] Lustre: DEBUG MARKER: == sanity-sec test 15: test id mapping =================== 15:57:43 (1787601463) [ 1016.609714] Lustre: DEBUG MARKER: == sanity-sec test 16: test nodemap all_off fileops ====== 16:00:35 (1787601635) [ 1111.009332] Lustre: lustre-OST0001-osc-ffff9b96e0a32000: disconnect after 20s idle [ 1111.021059] Lustre: Skipped 1 previous similar message [ 1162.209741] Lustre: lustre-OST0001-osc-ffff9b96e0a32000: disconnect after 24s idle [ 1254.529940] Lustre: DEBUG MARKER: == sanity-sec test 17: test nodemap trusted_noadmin fileops ========================================================== 16:04:33 (1787601873) [ 1259.491204] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 20s idle [ 1320.930327] Lustre: lustre-OST0001-osc-ffff9b96e0a32000: disconnect after 21s idle [ 1320.937149] Lustre: Skipped 1 previous similar message [ 1346.528480] Lustre: lustre-OST0001-osc-ffff9b96e0a32000: disconnect after 20s idle [ 1367.008512] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 21s idle [ 1418.208311] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 21s idle [ 1489.888221] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 25s idle [ 1489.904743] Lustre: Skipped 1 previous similar message [ 1587.168726] Lustre: lustre-OST0001-osc-ffff9b96e0a32000: disconnect after 20s idle [ 1587.176618] Lustre: Skipped 2 previous similar messages [ 1725.408427] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 22s idle [ 1725.422344] Lustre: Skipped 3 previous similar messages [ 1776.259482] Lustre: DEBUG MARKER: == sanity-sec test 18: test nodemap mapped_noadmin fileops ========================================================== 16:13:14 (1787602394) [ 2001.890709] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 20s idle [ 2001.906422] Lustre: Skipped 5 previous similar messages [ 2055.116520] Lustre: DEBUG MARKER: == sanity-sec test 19: test nodemap trusted_admin fileops ========================================================== 16:17:53 (1787602673) [ 2239.858141] Lustre: DEBUG MARKER: == sanity-sec test 20: test nodemap mapped_admin fileops ========================================================== 16:20:58 (1787602858) [ 2423.968393] Lustre: DEBUG MARKER: == sanity-sec test 21: test nodemap mapped_trusted_noadmin fileops ========================================================== 16:24:02 (1787603042) [ 2534.368524] Lustre: lustre-OST0000-osc-ffff9b96e0a32000: disconnect after 20s idle [ 2534.371471] Lustre: Skipped 10 previous similar messages [ 2705.985905] Lustre: DEBUG MARKER: == sanity-sec test 22: test nodemap mapped_trusted_admin fileops ========================================================== 16:28:44 (1787603324) [ 2888.150506] Lustre: DEBUG MARKER: == sanity-sec test 23a: test mapped regular ACLs ========= 16:31:46 (1787603506) [ 2890.152914] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23a Need 2 clients at least [ 2891.960844] Lustre: DEBUG MARKER: == sanity-sec test 23b: test mapped default ACLs ========= 16:31:50 (1787603510) [ 2893.591587] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23b Need 2 clients at least [ 2895.427753] Lustre: DEBUG MARKER: == sanity-sec test 24: check nodemap proc files for LBUGs and Oopses ========================================================== 16:31:54 (1787603514) [ 2935.037969] Lustre: DEBUG MARKER: == sanity-sec test 25a: test save and reload nodemap config ========================================================== 16:32:33 (1787603553) [ 2938.847026] Lustre: Unmounted lustre-client [ 2972.523390] Lustre: DEBUG MARKER: === sanity-sec: start setup 16:33:10 (1787603590) === [ 3019.869933] LustreError: 63984:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 406us [ 3019.923116] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3025.214495] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 3035.425774] Lustre: DEBUG MARKER: === sanity-sec: finish setup 16:34:14 (1787603654) === [ 3037.758088] Lustre: Unmounted lustre-client [ 3052.745828] LustreError: 65059:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 391us [ 3052.781888] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3061.898597] Lustre: DEBUG MARKER: == sanity-sec test 25b: test nodemap info values ========= 16:34:39 (1787603679) [ 3112.142841] Lustre: DEBUG MARKER: == sanity-sec test 25c: test yaml-compliance for nodemap ========================================================== 16:35:30 (1787603730) [ 3139.950775] Lustre: Unmounted lustre-client [ 3140.438349] LustreError: 67341:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 742us [ 3140.524900] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3150.577511] Lustre: Unmounted lustre-client [ 3162.406578] LustreError: 68018:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 4165us [ 3162.474820] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3164.154389] Lustre: DEBUG MARKER: SKIP: sanity-sec test_26 skipping SLOW test 26 [ 3165.882334] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27a skipping excluded test 27a (base 27) [ 3168.151773] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27aa skipping excluded test 27aa (base 27) [ 3170.042299] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ab skipping excluded test 27ab (base 27) [ 3171.919859] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ac skipping excluded test 27ac (base 27) [ 3173.611667] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ad skipping excluded test 27ad (base 27) [ 3175.399626] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27b skipping excluded test 27b (base 27) [ 3177.084453] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27c skipping excluded test 27c (base 27) [ 3178.509645] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27d skipping excluded test 27d (base 27) [ 3180.384535] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27e skipping excluded test 27e (base 27) [ 3182.344797] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27f skipping excluded test 27f (base 27) [ 3184.257537] Lustre: DEBUG MARKER: == sanity-sec test 28: check shared key rotation method == 16:36:42 (1787603802) [ 3186.049520] Lustre: DEBUG MARKER: SKIP: sanity-sec test_28 need shared key feature for this test [ 3187.798561] Lustre: DEBUG MARKER: == sanity-sec test 29: check for missing shared key ====== 16:36:46 (1787603806) [ 3189.488822] Lustre: DEBUG MARKER: SKIP: sanity-sec test_29 need shared key feature for this test [ 3191.158536] Lustre: DEBUG MARKER: == sanity-sec test 30: check for invalid shared key ====== 16:36:49 (1787603809) [ 3192.985930] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30 need shared key feature for this test [ 3194.724881] Lustre: DEBUG MARKER: == sanity-sec test 30b: basic test of all different SSK flavors ========================================================== 16:36:53 (1787603813) [ 3196.532666] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30b need shared key feature for this test [ 3198.299706] Lustre: DEBUG MARKER: == sanity-sec test 31: client mount option '-o network' == 16:36:57 (1787603817) [ 3202.014716] Lustre: DEBUG MARKER: SKIP: sanity-sec test_31 without lnetctl support. [ 3203.884805] Lustre: DEBUG MARKER: == sanity-sec test 32: check for mgssec ================== 16:37:02 (1787603822) [ 3206.390703] Lustre: DEBUG MARKER: SKIP: sanity-sec test_32 need shared key feature for this test [ 3208.523776] Lustre: DEBUG MARKER: == sanity-sec test 33: correct srpc flags for MGS connection ========================================================== 16:37:07 (1787603827) [ 3210.605059] Lustre: DEBUG MARKER: SKIP: sanity-sec test_33 need shared key feature for this test [ 3213.182549] Lustre: DEBUG MARKER: == sanity-sec test 34: deny_unknown on default nodemap === 16:37:11 (1787603831) [ 3241.881173] Lustre: DEBUG MARKER: == sanity-sec test 35: Check permissions when accessing changelogs ========================================================== 16:37:39 (1787603859) [ 3271.427714] LustreError: 73225:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9b96c515b800: fail to open changelog catalog: rc = -13 [ 3286.749135] Lustre: DEBUG MARKER: == sanity-sec test 36: control if clients can use encryption ========================================================== 16:38:25 (1787603905) [ 3288.965285] Lustre: Unmounted lustre-client [ 3289.271606] LustreError: 73643:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 553us [ 3289.317210] Lustre: Test dummy encryption mode enabled [ 3289.335086] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3289.573174] llcrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-aesni)" [ 3296.925679] Lustre: Test dummy encryption mode enabled [ 3299.090688] Lustre: Unmounted lustre-client [ 3299.097631] Lustre: Skipped 1 previous similar message [ 3303.826551] LustreError: 73955:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1810us [ 3303.840949] LustreError: 73955:0:(obd_config.c:1432:process_param2_config()) Skipped 1 previous similar message [ 3303.861880] Lustre: lustre-MDT0000-mdc-ffff9b96d0ad6000: connection denied by lustre-MDT0000_UUID: rc = -13 [ 3303.874571] LustreError: 73931:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9b96d0ad6000: can't stat MDS #0: rc = -13 [ 3303.926711] LustreError: 73931:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -13 [ 3323.990721] LustreError: 74657:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 5092us [ 3324.042271] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3324.046112] Lustre: Skipped 1 previous similar message [ 3326.955814] Lustre: Unmounted lustre-client [ 3326.956968] Lustre: Skipped 1 previous similar message [ 3329.005263] bash (73436): drop_caches: 3 [ 3332.038555] Lustre: DEBUG MARKER: == sanity-sec test 37: simple encrypted file ============= 16:39:10 (1787603950) [ 3333.740829] Lustre: DEBUG MARKER: SKIP: sanity-sec test_37 ldiskfs only test (using debugfs) [ 3335.651599] Lustre: DEBUG MARKER: == sanity-sec test 38: encrypted file with hole ========== 16:39:14 (1787603954) [ 3337.089537] Lustre: DEBUG MARKER: SKIP: sanity-sec test_38 skip ZFS backend [ 3338.879991] Lustre: DEBUG MARKER: == sanity-sec test 39: rewrite data in already encrypted page ========================================================== 16:39:17 (1787603957) [ 3342.446709] Lustre: Test dummy encryption mode enabled [ 3342.467359] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3342.478254] Lustre: Skipped 1 previous similar message [ 3343.071893] llcrypt: AES-256-XTS using implementation "xts-aes-aesni" [ 3355.605842] bash (75365): drop_caches: 3 [ 3359.704723] Lustre: DEBUG MARKER: == sanity-sec test 40: exercise size of encrypted file === 16:39:36 (1787603976) [ 3363.868856] Lustre: Unmounted lustre-client [ 3363.874421] Lustre: Skipped 2 previous similar messages [ 3364.620709] LustreError: 76335:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 4274us [ 3364.657658] LustreError: 76335:0:(obd_config.c:1432:process_param2_config()) Skipped 3 previous similar messages [ 3364.762090] Lustre: Test dummy encryption mode enabled [ 3370.268515] bash (76129): drop_caches: 3 [ 3381.718593] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3381.731408] Lustre: Skipped 3 previous similar messages [ 3382.318480] bash (76129): drop_caches: 3 [ 3385.664945] Lustre: DEBUG MARKER: == sanity-sec test 41: test race on encrypted file size (1) ========================================================== 16:40:03 (1787604003) [ 3388.850081] Lustre: Test dummy encryption mode enabled [ 3416.111636] bash (77082): drop_caches: 3 [ 3418.512543] Lustre: DEBUG MARKER: == sanity-sec test 42: test race on encrypted file size (2) ========================================================== 16:40:36 (1787604036) [ 3421.211598] Lustre: Test dummy encryption mode enabled [ 3448.086207] Lustre: Unmounted lustre-client [ 3448.088931] Lustre: Skipped 5 previous similar messages [ 3448.357193] LustreError: 78649:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 525us [ 3448.364625] LustreError: 78649:0:(obd_config.c:1432:process_param2_config()) Skipped 6 previous similar messages [ 3448.407760] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3448.412685] Lustre: Skipped 4 previous similar messages [ 3450.452559] bash (77874): drop_caches: 3 [ 3453.440323] Lustre: DEBUG MARKER: == sanity-sec test 43: test race on encrypted file size (3) ========================================================== 16:41:11 (1787604071) [ 3456.761481] Lustre: Test dummy encryption mode enabled [ 3456.764496] Lustre: Skipped 1 previous similar message [ 3487.476196] bash (78715): drop_caches: 3 [ 3490.592518] Lustre: DEBUG MARKER: == sanity-sec test 44: encrypted file access semantics: direct IO ========================================================== 16:41:48 (1787604108) [ 3492.807444] Lustre: DEBUG MARKER: SKIP: sanity-sec test_44 This test needs vmtouch utility [ 3494.791540] Lustre: DEBUG MARKER: == sanity-sec test 45: encrypted file access semantics: MMAP ========================================================== 16:41:53 (1787604113) [ 3498.683883] Lustre: Test dummy encryption mode enabled [ 3498.687205] Lustre: Skipped 1 previous similar message [ 3507.539763] bash (79852): drop_caches: 3 [ 3509.982653] Lustre: DEBUG MARKER: == sanity-sec test 46: encrypted file access semantics without key ========================================================== 16:42:08 (1787604128) [ 3514.560834] bash (80622): drop_caches: 3 [ 3517.803420] bash (80622): drop_caches: 3 [ 3518.592861] LustreError: 80980:0:(llite_lib.c:4132:ll_prep_md_op_data()) lustre: failed to setup filename: rc = -126 [ 3527.633580] bash (80622): drop_caches: 3 [ 3529.762246] Lustre: DEBUG MARKER: == sanity-sec test 47: encrypted file access semantics: rename/link ========================================================== 16:42:28 (1787604148) [ 3541.850774] bash (81505): drop_caches: 3 [ 3567.954565] bash (81505): drop_caches: 3 [ 3577.839162] Lustre: Unmounted lustre-client [ 3577.840802] Lustre: Skipped 11 previous similar messages [ 3578.425387] LustreError: 82580:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1544us [ 3578.445178] LustreError: 82580:0:(obd_config.c:1432:process_param2_config()) Skipped 10 previous similar messages [ 3578.493585] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3578.502914] Lustre: Skipped 10 previous similar messages [ 3579.288457] bash (81505): drop_caches: 3 [ 3582.631529] Lustre: DEBUG MARKER: == sanity-sec test 48a: encrypted file access semantics: truncate ========================================================== 16:43:20 (1787604200) [ 3586.744873] Lustre: Test dummy encryption mode enabled [ 3586.750752] Lustre: Skipped 2 previous similar messages [ 3590.055510] bash (82624): drop_caches: 3 [ 3594.803891] bash (82624): drop_caches: 3 [ 3608.894212] bash (82624): drop_caches: 3 [ 3613.012075] Lustre: DEBUG MARKER: == sanity-sec test 48b: encrypted file: concurrent truncate ========================================================== 16:43:49 (1787604229) [ 3614.920415] Lustre: DEBUG MARKER: SKIP: sanity-sec test_48b Need at least 2 clients [ 3616.599073] Lustre: DEBUG MARKER: == sanity-sec test 49: Avoid getxattr for encryption context ========================================================== 16:43:55 (1787604235) [ 3620.882221] bash (83856): drop_caches: 3 [ 3621.655803] bash (83856): drop_caches: 3 [ 3623.216683] bash (83856): drop_caches: 3 [ 3624.581568] bash (83856): drop_caches: 3 [ 3628.312731] Lustre: DEBUG MARKER: SKIP: sanity-sec test_49 2nd part needs >= 2 MDTs [ 3637.329493] bash (83856): drop_caches: 3 [ 3640.524687] Lustre: DEBUG MARKER: == sanity-sec test 50: DoM encrypted file ================ 16:44:18 (1787604258) [ 3646.085545] bash (84867): drop_caches: 3 [ 3646.635643] bash (84867): drop_caches: 3 [ 3647.270715] Lustre: 85124:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3647.670918] bash (84867): drop_caches: 3 [ 3648.311934] bash (84867): drop_caches: 3 [ 3648.828334] Lustre: 85150:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3649.241461] bash (84867): drop_caches: 3 [ 3649.991526] bash (84867): drop_caches: 3 [ 3650.681633] Lustre: 85175:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3651.170495] bash (84867): drop_caches: 3 [ 3652.040152] bash (84867): drop_caches: 3 [ 3652.949983] bash (84867): drop_caches: 3 [ 3653.498960] bash (84867): drop_caches: 3 [ 3653.977992] Lustre: 85226:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3653.993354] Lustre: 85226:0:(file.c:676:ll_dom_finish_open()) Skipped 1 previous similar message [ 3654.404827] bash (84867): drop_caches: 3 [ 3655.144720] bash (84867): drop_caches: 3 [ 3656.410926] bash (84867): drop_caches: 3 [ 3657.405421] bash (84867): drop_caches: 3 [ 3658.400799] bash (84867): drop_caches: 3 [ 3658.921650] bash (84867): drop_caches: 3 [ 3660.365273] bash (84867): drop_caches: 3 [ 3661.229222] bash (84867): drop_caches: 3 [ 3662.895237] bash (84867): drop_caches: 3 [ 3663.643617] bash (84867): drop_caches: 3 [ 3664.858717] bash (84867): drop_caches: 3 [ 3665.395529] bash (84867): drop_caches: 3 [ 3666.166167] Lustre: 85380:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x3:0x0] with data: rc = -126 [ 3666.175634] Lustre: 85380:0:(file.c:676:ll_dom_finish_open()) Skipped 2 previous similar messages [ 3666.685452] bash (84867): drop_caches: 3 [ 3667.334896] bash (84867): drop_caches: 3 [ 3668.679754] bash (84867): drop_caches: 3 [ 3669.471092] bash (84867): drop_caches: 3 [ 3680.205777] bash (84867): drop_caches: 3 [ 3682.884859] Lustre: DEBUG MARKER: == sanity-sec test 51: FS capabilities =================== 16:45:00 (1787604300) [ 3740.835090] Lustre: DEBUG MARKER: == sanity-sec test 52: Mirrored encrypted file =========== 16:45:59 (1787604359) [ 3745.399227] Lustre: Test dummy encryption mode enabled [ 3745.414065] Lustre: Skipped 2 previous similar messages [ 3751.775967] LustreError: 87578:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9b96d0ad1800: inode [0x200000412:0x4:0x0] mdc close failed: rc = -22 [ 3763.590437] bash (87288): drop_caches: 3 [ 3767.010286] Lustre: DEBUG MARKER: == sanity-sec test 53: Mixed PAGE_SIZE clients =========== 16:46:24 (1787604384) [ 3769.148441] Lustre: DEBUG MARKER: SKIP: sanity-sec test_53 Need 64K PAGE_SIZE client [ 3771.160715] Lustre: DEBUG MARKER: == sanity-sec test 54: Encryption policies with fscrypt == 16:46:29 (1787604389) [ 3773.646212] Lustre: DEBUG MARKER: SKIP: sanity-sec test_54 This test needs fscrypt userspace tool [ 3775.714678] Lustre: DEBUG MARKER: == sanity-sec test 55: access with seteuid =============== 16:46:34 (1787604394) [ 3818.814666] Lustre: DEBUG MARKER: == sanity-sec test 56: FIEMAP on encrypted file ========== 16:47:17 (1787604437) [ 3820.729159] Lustre: DEBUG MARKER: SKIP: sanity-sec test_56 skip ZFS backend [ 3822.761588] Lustre: DEBUG MARKER: == sanity-sec test 57: security.c/encryption.c xattr protection ========================================================== 16:47:21 (1787604441) [ 3824.503270] Lustre: DEBUG MARKER: SKIP: sanity-sec test_57 skip ZFS backend [ 3826.442278] Lustre: DEBUG MARKER: == sanity-sec test 58: access to enc file's xattrs ======= 16:47:24 (1787604444) [ 3828.048876] Lustre: DEBUG MARKER: SKIP: sanity-sec test_58 skip ZFS backend [ 3829.747953] Lustre: DEBUG MARKER: == sanity-sec test 59a: mirror resync of encrypted files without key ========================================================== 16:47:28 (1787604448) [ 3834.861275] Lustre: Unmounted lustre-client [ 3834.863469] Lustre: Skipped 12 previous similar messages [ 3835.269855] LustreError: 90978:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 957us [ 3835.284488] LustreError: 90978:0:(obd_config.c:1432:process_param2_config()) Skipped 12 previous similar messages [ 3835.341269] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 3835.343906] Lustre: Skipped 12 previous similar messages [ 3835.928199] bash (90687): drop_caches: 3 [ 3837.912437] bash (90687): drop_caches: 3 [ 3856.419597] bash (90687): drop_caches: 3 [ 3860.408890] Lustre: DEBUG MARKER: == sanity-sec test 59b: migrate/extend/split of encrypted files without key ========================================================== 16:47:57 (1787604477) [ 3869.996510] bash (91641): drop_caches: 3 [ 3872.201214] bash (91641): drop_caches: 3 [ 3880.258618] bash (91641): drop_caches: 3 [ 3882.389650] bash (91641): drop_caches: 3 [ 3891.257823] bash (91641): drop_caches: 3 [ 3891.708521] LustreError: 92373:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9b96c5143800: inode [0x200000416:0x2:0x0] mdc close failed: rc = -22 [ 3892.244174] bash (91641): drop_caches: 3 [ 3906.169708] bash (91641): drop_caches: 3 [ 3909.238945] Lustre: DEBUG MARKER: == sanity-sec test 59c: MDT migrate of encrypted files without key ========================================================== 16:48:46 (1787604526) [ 3911.860763] Lustre: DEBUG MARKER: SKIP: sanity-sec test_59c needs >= 2 MDTs [ 3914.581548] Lustre: DEBUG MARKER: == sanity-sec test 60: Subdirmount of encrypted dir ====== 16:48:52 (1787604532) [ 3918.361519] bash (93292): drop_caches: 3 [ 3922.356197] bash (93292): drop_caches: 3 [ 3935.399535] bash (93292): drop_caches: 3 [ 3938.721302] Lustre: DEBUG MARKER: == sanity-sec test 61: Nodemap enforces read-only mount == 16:49:16 (1787604556) [ 3973.095117] Lustre: lustre-MDT0000-mdc-ffff9b96e0a32000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3973.108413] LustreError: 94886:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9b96e0a32000: can't stat MDS #0: rc = -30 [ 3973.117947] LustreError: 94886:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9b96e0a32000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3976.138744] Lustre: lustre-MDT0000-mdc-ffff9b96d058a000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3976.149782] LustreError: 94970:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9b96d058a000: can't stat MDS #0: rc = -30 [ 3976.162483] LustreError: 94970:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9b96d058a000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3981.440556] Lustre: lustre-MDT0000-mdc-ffff9b96d8598000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3981.448406] LustreError: 95136:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9b96d8598000: can't stat MDS #0: rc = -30 [ 3981.459738] LustreError: 95136:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9b96d8598000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 4000.368239] Lustre: DEBUG MARKER: == sanity-sec test 62: e2fsck with encrypted files ======= 16:50:18 (1787604618) [ 4002.181939] Lustre: DEBUG MARKER: SKIP: sanity-sec test_62 skip ZFS backend [ 4003.970685] Lustre: DEBUG MARKER: == sanity-sec test 63: fid2path with encrypted files ===== 16:50:22 (1787604622) [ 4006.222932] Lustre: DEBUG MARKER: SKIP: sanity-sec test_63 This test needs fscrypt userspace tool [ 4007.949958] Lustre: DEBUG MARKER: == sanity-sec test 64a: Nodemap enforces file_perms RBAC roles ========================================================== 16:50:26 (1787604626) [ 4088.810447] Lustre: DEBUG MARKER: == sanity-sec test 64b: Nodemap enforces dne_ops RBAC roles ========================================================== 16:51:46 (1787604706) [ 4090.576967] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64b mdt count 1, skipping dne_ops role [ 4092.799901] Lustre: DEBUG MARKER: == sanity-sec test 64c: Nodemap enforces quota related RBAC roles ========================================================== 16:51:51 (1787604711) [ 4132.669983] LustreError: 98846:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9b96dfbd9800: ptlrpc_queue_wait failed: rc = -1 [ 4133.172749] LustreError: 98863:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9b96dfbd9800: ptlrpc_queue_wait failed: rc = -1 [ 4133.180813] LustreError: 98863:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 16 previous similar messages [ 4157.378091] LustreError: 99222:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9b96dfbd9800: ptlrpc_queue_wait failed: rc = -1 [ 4157.387415] LustreError: 99222:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 6 previous similar messages [ 4184.736610] Lustre: DEBUG MARKER: == sanity-sec test 64d: Nodemap enforces byfid_ops RBAC roles ========================================================== 16:53:23 (1787604803) [ 4261.390376] Lustre: DEBUG MARKER: == sanity-sec test 64e: Nodemap enforces chlg_ops RBAC roles ========================================================== 16:54:39 (1787604879) [ 4300.577782] LustreError: 102060:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9b96dfbd9800: fail to open changelog catalog: rc = -13 [ 4330.836693] LustreError: 102510:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9b96dfbd9800: fail to open changelog catalog: rc = -13 [ 4363.189750] Lustre: DEBUG MARKER: == sanity-sec test 64f: Nodemap enforces fscrypt_admin RBAC roles ========================================================== 16:56:20 (1787604980) [ 4366.041767] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64f Need fscrypt, skip fscrypt_admin role [ 4368.838209] Lustre: DEBUG MARKER: == sanity-sec test 64g: Nodemap enforces server_upcall RBAC role ========================================================== 16:56:27 (1787604987) [ 4443.671435] Lustre: DEBUG MARKER: == sanity-sec test 64h: Nodemap enforces local_admin RBAC roles ========================================================== 16:57:42 (1787605062) [ 4470.960174] LustreError: 105734:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9b96dfbd9800: ptlrpc_queue_wait failed: rc = -1 [ 4470.969156] LustreError: 105734:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 2 previous similar messages [ 4476.595629] LustreError: 105819:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9b96dfbd9800: ptlrpc_queue_wait failed: rc = -1 [ 4503.954417] Lustre: DEBUG MARKER: == sanity-sec test 64i: Nodemap quota enforcement with local_admin RBAC and offsets ========================================================== 16:58:42 (1787605122) [ 4741.597889] Lustre: Unmounted lustre-client [ 4741.601601] Lustre: Skipped 20 previous similar messages [ 4752.935034] LustreError: 110408:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2831us [ 4752.948271] LustreError: 110408:0:(obd_config.c:1432:process_param2_config()) Skipped 20 previous similar messages [ 4753.028162] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 4753.030291] Lustre: Skipped 20 previous similar messages [ 4757.355058] Lustre: DEBUG MARKER: == sanity-sec test 64j: Nodemap enforces projid_set RBAC role ========================================================== 17:02:55 (1787605375) [ 4847.121114] Lustre: DEBUG MARKER: == sanity-sec test 64k: Nodemap enforces foreign_ops RBAC roles ========================================================== 17:04:25 (1787605465) [ 4896.591211] Lustre: DEBUG MARKER: == sanity-sec test 64l: Nodemap enforces immutable_flags RBAC role ========================================================== 17:05:14 (1787605514) [ 4943.127187] Lustre: DEBUG MARKER: == sanity-sec test 65: lfs find -printf %La and --attrs support ========================================================== 17:06:01 (1787605561) [ 4945.448193] LustreError: 114560:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9b96d058b800: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4945.805178] Lustre: Test dummy encryption mode enabled [ 4945.807229] Lustre: Skipped 8 previous similar messages [ 4946.823947] LustreError: 114653:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9b96d8596000: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4956.649420] LustreError: 115313:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9b96d8596000: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4956.657728] LustreError: 115313:0:(file.c:251:ll_close_inode_openhandle()) Skipped 1 previous similar message [ 4957.534095] bash (114379): drop_caches: 3 [ 4960.992632] Lustre: DEBUG MARKER: == sanity-sec test 68: all config logs are processed ===== 17:06:18 (1787605578) [ 4966.518199] LustreError: 2352:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d sleeping for 20000ms [ 4971.616651] LustreError: 115584:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.124@tcp: failed processing log, type 1: rc = -110 [ 4986.537359] LustreError: 2352:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d awake [ 5001.805188] Lustre: DEBUG MARKER: == sanity-sec test 69: check upcall incorrect values ===== 17:07:00 (1787605620) [ 5019.268058] Lustre: DEBUG MARKER: == sanity-sec test 70: targets have local copy of sptlrpc llog ========================================================== 17:07:17 (1787605637) [ 5022.370659] Lustre: DEBUG MARKER: SKIP: sanity-sec test_70 need shared key feature for this test [ 5024.453641] Lustre: DEBUG MARKER: == sanity-sec test 71: encryption does not remove project flag ========================================================== 17:07:23 (1787605643) [ 5026.625293] Lustre: DEBUG MARKER: SKIP: sanity-sec test_71 Need fscrypt [ 5028.246868] Lustre: DEBUG MARKER: == sanity-sec test 72a: dynamic nodemap properties on OSS ========================================================== 17:07:27 (1787605647) [ 5140.237823] Lustre: DEBUG MARKER: == sanity-sec test 72b: dynamic nodemap properties on MDS ========================================================== 17:09:18 (1787605758) [ 5262.224907] Lustre: DEBUG MARKER: == sanity-sec test 72c: child_raise_privileges nodemap property ========================================================== 17:11:21 (1787605881) [ 5311.275161] Lustre: DEBUG MARKER: == sanity-sec test 72d: fileset inheritance for dynamic nodemap ========================================================== 17:12:09 (1787605929) [ 5379.232273] Lustre: DEBUG MARKER: == sanity-sec test 72e: dynamic nodemap reclassify ======= 17:13:17 (1787605997) [ 5381.597270] Lustre: Unmounted lustre-client [ 5381.605272] Lustre: Skipped 4 previous similar messages [ 5396.296499] LustreError: 123354:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 9752us [ 5396.315547] LustreError: 123354:0:(obd_config.c:1432:process_param2_config()) Skipped 4 previous similar messages [ 5396.381693] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 5396.385382] Lustre: Skipped 4 previous similar messages [ 5421.965932] Lustre: DEBUG MARKER: == sanity-sec test 72f: fileset_modify on dynamic nodemap ========================================================== 17:14:01 (1787606041) [ 5488.828783] Lustre: DEBUG MARKER: == sanity-sec test 73: encrypted names in changelogs ===== 17:15:07 (1787606107) [ 5491.151856] Lustre: DEBUG MARKER: SKIP: sanity-sec test_73 Need fscrypt [ 5493.038849] Lustre: DEBUG MARKER: == sanity-sec test 74: Set nodemap deny_mount flag ======= 17:15:11 (1787606111) [ 5528.105577] LustreError: 126251:0:(llite_lib.c:605:client_common_fill_super()) lustre-clilmv-ffff9b96dfbc1800: cannot mds_connect: rc = -1 [ 5528.141144] LustreError: 126251:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 5550.824724] Lustre: DEBUG MARKER: == sanity-sec test 75: check uid/gid/projid are set on OST and MDT for various RPCs ========================================================== 17:16:08 (1787606168) [ 5553.081324] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75 ldiskfs only test (using debugfs) [ 5555.546591] Lustre: DEBUG MARKER: == sanity-sec test 75a: test resource fs IDs against nodemap offset ========================================================== 17:16:13 (1787606173) [ 5560.041705] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75a need at least two clients [ 5562.296745] Lustre: DEBUG MARKER: == sanity-sec test 75b: test resource ID repair ========== 17:16:20 (1787606180) [ 5565.792244] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75b ldiskfs only test (using debugfs) [ 5567.514080] Lustre: DEBUG MARKER: == sanity-sec test 76: suppgroups and gid mapping ======== 17:16:26 (1787606186) [ 5612.093297] Lustre: DEBUG MARKER: == sanity-sec test 77: root offsetting =================== 17:17:10 (1787606230) [ 5658.364028] Lustre: DEBUG MARKER: == sanity-sec test 78: nodemap stats ===================== 17:17:56 (1787606276) [ 5702.245280] Lustre: DEBUG MARKER: == sanity-sec test 79: ssk for nodemap identification ==== 17:18:41 (1787606321) [ 5704.449391] Lustre: DEBUG MARKER: SKIP: sanity-sec test_79 Need shared key feature for this test [ 5706.207348] Lustre: DEBUG MARKER: == sanity-sec test 81a: nodemap ban list ================= 17:18:45 (1787606325) [ 5707.912605] Lustre: DEBUG MARKER: test_81a 24811 [ 5729.422576] Lustre: This client was banned by administrative request for file system lustre. All requests will get Operation not permitted. [ 5729.429596] LustreError: 132268:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5767.100534] LustreError: 132848:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5767.113713] LustreError: 132848:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5786.657122] LustreError: 133074:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.124@tcp: failed processing log, type 1: rc = -110 [ 5922.786708] LustreError: MGC192.168.202.124@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 5922.837978] LustreError: 133074:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 5934.371414] LustreError: 133315:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5934.384030] LustreError: 133315:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5940.385682] LustreError: 133353:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.124@tcp: failed processing log, type 1: rc = -110 [ 6078.433096] LustreError: MGC192.168.202.124@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 6078.452783] Lustre: Unmounted lustre-client [ 6078.461623] Lustre: Skipped 11 previous similar messages [ 6078.470704] LustreError: 133353:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 6080.750098] LustreError: 133440:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 608us [ 6080.758649] LustreError: 133440:0:(obd_config.c:1432:process_param2_config()) Skipped 9 previous similar messages [ 6080.801387] Lustre: Mounted lustre-client - version 2.17.57_82_gfc0532e [ 6080.804554] Lustre: Skipped 8 previous similar messages [ 6101.372122] Lustre: DEBUG MARKER: == sanity-sec test 81b: banned client does not block other ========================================================== 17:25:20 (1787606720) [ 6102.931343] Lustre: DEBUG MARKER: SKIP: sanity-sec test_81b Need 2 clients [ 6105.040457] Lustre: DEBUG MARKER: == sanity-sec test 82: export lock revoked after nodemap change ========================================================== 17:25:23 (1787606723) [ 6172.542743] Lustre: DEBUG MARKER: == sanity-sec test 83: Suppgids for cross-MDT ops ======== 17:26:31 (1787606791) [ 6174.434757] Lustre: DEBUG MARKER: SKIP: sanity-sec test_83 needs >= 2 MDTs [ 6176.311919] Lustre: DEBUG MARKER: == sanity-sec test 84: do not squash trusted ids ========= 17:26:35 (1787606795) [ 6217.647792] Lustre: DEBUG MARKER: == sanity-sec test 85: forbid squashing to UID/GID 0 ===== 17:27:16 (1787606836) [ 6263.711409] Lustre: DEBUG MARKER: == sanity-sec test 93: incremental RBAC role modifications ========================================================== 17:28:02 (1787606882) [ 6347.307125] Lustre: DEBUG MARKER: == sanity-sec test 100: SSK automatic prime generation, binary/ASCII server keys ========================================================== 17:29:25 (1787606965) [ 6348.923660] Lustre: DEBUG MARKER: SKIP: sanity-sec test_100 Need shared key feature for this test [ 6351.333881] Lustre: DEBUG MARKER: == sanity-sec test 101: lgss_sk -a and -l support for ascii-encoded SSK keys ========================================================== 17:29:29 (1787606969) [ 6353.522931] Lustre: DEBUG MARKER: SKIP: sanity-sec test_101 Need shared key feature for this test [ 6355.880911] Lustre: DEBUG MARKER: == sanity-sec test 102: SSK automatic key loading from mount point ========================================================== 17:29:34 (1787606974) [ 6357.220396] Lustre: DEBUG MARKER: SKIP: sanity-sec test_102 Need shared key feature for this test [ 6359.405984] Lustre: DEBUG MARKER: == sanity-sec test 103: Multiple SSK keys on server side ========================================================== 17:29:37 (1787606977) [ 6361.160094] Lustre: DEBUG MARKER: SKIP: sanity-sec test_103 Need shared key feature for this test [ 6363.418951] Lustre: DEBUG MARKER: == sanity-sec test 104: SSK key removal from keyring ===== 17:29:41 (1787606981) [ 6364.917140] Lustre: DEBUG MARKER: SKIP: sanity-sec test_104 Need shared key feature for this test [ 6366.790932] Lustre: DEBUG MARKER: == sanity-sec test 105: update nodemap membership on flavor change ========================================================== 17:29:45 (1787606985) [ 6368.549398] Lustre: DEBUG MARKER: SKIP: sanity-sec test_105 Need shared key feature for this test [ 6370.532605] Lustre: DEBUG MARKER: == sanity-sec test 106: switch nodemap to gssonly ======== 17:29:49 (1787606989) [ 6371.849077] Lustre: DEBUG MARKER: SKIP: sanity-sec test_106 Need shared key feature for this test [ 6373.864182] Lustre: DEBUG MARKER: == sanity-sec test 200: sk_load_key broadens SSK key perms without @u linked ========================================================== 17:29:52 (1787606992) [ 6375.653712] Lustre: DEBUG MARKER: SKIP: sanity-sec test_200 Need shared key feature for this test [ 6377.667741] Lustre: DEBUG MARKER: == sanity-sec test 300: test user_principal mount option parsing ========================================================== 17:29:56 (1787606996) [ 6379.623105] Lustre: DEBUG MARKER: Mount with user_principal=mock_iam_test [ 6386.498564] Lustre: DEBUG MARKER: Mount with only user_principal (should fail) [ 6387.098168] LustreError: Unknown option 'user_principal', won't mount. [ 6387.129452] LustreError: 142808:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -22 [ 6389.118324] Lustre: DEBUG MARKER: Mount failed as expected with only -o user_principal [ 6396.405519] Lustre: DEBUG MARKER: cleanup: ====================================================== [ 6398.305206] Lustre: DEBUG MARKER: == sanity-sec test complete, duration 6106 sec =========== 17:30:16 (1787607016) [ 6400.725299] Lustre: DEBUG MARKER: === sanity-sec: start cleanup 17:30:18 (1787607018) === [ 6404.528664] Lustre: DEBUG MARKER: === sanity-sec: finish cleanup 17:30:23 (1787607023) === [ 6433.177848] Key type lgssc unregistered [ 6433.474792] LNet: 144578:0:(lib-ptl.c:964:lnet_clear_lazy_portal()) Active lazy portal 0 on exit [ 6433.481530] LNetError: 144578:0:(acceptor.c:252:lnet_acceptor_remove_socket()) Interface ens2 not found [ 6433.507029] LNet: Removed LNI 192.168.202.24@tcp [ 6434.275874] Key type .llcrypt unregistered [ 6434.277529] Key type ._llcrypt unregistered