[ 0.000000] Linux version 4.18.0rh8.10-debug (green@maintenance) (gcc version 8.5.0 20210514 (Red Hat 8.5.0-26) (GCC)) #2 SMP Mon Jul 14 01:24:22 EDT 2025 [ 0.000000] Command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.000000] signal: max sigframe size: 1776 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffd9fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bffda000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000146dfffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-10.fc44 06/10/2025 [ 0.000000] Hypervisor detected: KVM [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: using sched offset of 457735451 cycles [ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.000000] tsc: Detected 2399.998 MHz processor [ 0.000000] last_pfn = 0x146e00 max_arch_pfn = 0x400000000 [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] last_pfn = 0xbffda max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f54d0-0x000f54df] [ 0.000000] RAMDISK: [mem 0xbcc64000-0xbffcffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F52F0 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x00000000BFFE2464 000034 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x00000000BFFE2300 000074 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x00000000BFFE0040 0022C0 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACS 0x00000000BFFE0000 000040 [ 0.000000] ACPI: APIC 0x00000000BFFE2374 000090 (v03 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x00000000BFFE2404 000038 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: WAET 0x00000000BFFE243C 000028 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: Reserving FACP table memory at [mem 0xbffe2300-0xbffe2373] [ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xbffe0040-0xbffe22ff] [ 0.000000] ACPI: Reserving FACS table memory at [mem 0xbffe0000-0xbffe003f] [ 0.000000] ACPI: Reserving APIC table memory at [mem 0xbffe2374-0xbffe2403] [ 0.000000] ACPI: Reserving HPET table memory at [mem 0xbffe2404-0xbffe243b] [ 0.000000] ACPI: Reserving WAET table memory at [mem 0xbffe243c-0xbffe2463] [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000146dfffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x1465a3000-0x1465cdfff] [ 0.000000] Reserving 256MB of memory at 2752MB for crashkernel (System RAM: 4205MB) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000bffd9fff] [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Zeroed struct page in unavailable ranges: 4744 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000146dfffff] [ 0.000000] ACPI: PM-Timer IO Port: 0x608 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] TSC deadline timer available [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] kvm-guest: KVM setup pv remote TLB flush [ 0.000000] kvm-guest: setup PV sched yield [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbffda000-0xbfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfeffbfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeffc000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] [mem 0xc0000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.000000] kvm-guest: PV spinlocks enabled [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1059618 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] Specific versions of hardware are certified with Red Hat Enterprise Linux 8. Please see the list of hardware certified with Red Hat Enterprise Linux 8 at https://catalog.redhat.com. [ 0.000000] audit: disabled (until reboot) [ 0.000000] software IO TLB: area num 4. [ 0.000000] Memory: 2829700K/4306400K available (18435K kernel code, 11221K rwdata, 7248K rodata, 2908K init, 18040K bss, 524584K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] ftrace: allocating 41240 entries in 162 pages [ 0.000000] ftrace: allocated 162 pages with 3 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.000000] rcu: RCU callback double-/use-after-free debug enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x622/0x9a8 with crng_init=0 [ 0.001000] Console: colour *CGA 80x25 [ 0.001000] printk: console [ttyS1] enabled [ 0.001000] ACPI: Core revision 20220331 [ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.001011] APIC: Switch to symmetric I/O mode setup [ 0.003070] x2apic enabled [ 0.004008] Switched APIC routing to physical x2apic. [ 0.005014] kvm-guest: setup PV IPIs [ 0.008795] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.009000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 0.009022] Calibrating delay loop (skipped) preset value.. 4799.99 BogoMIPS (lpj=2399998) [ 0.010014] pid_max: default: 32768 minimum: 301 [ 0.012121] LSM: Security Framework initializing [ 0.013063] Yama: becoming mindful. [ 0.014043] SELinux: Initializing. [ 0.015079] *** VALIDATE selinux *** [ 0.023900] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc) [ 0.028043] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc) [ 0.030065] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.031126] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.032158] *** VALIDATE tmpfs *** [ 0.033533] *** VALIDATE proc *** [ 0.035135] *** VALIDATE cgroup *** [ 0.036015] *** VALIDATE cgroup2 *** [ 0.038120] x86/cpu: User Mode Instruction Prevention (UMIP) activated [ 0.039172] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.040011] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.041047] Spectre V2 : User space: Vulnerable [ 0.042013] Speculative Store Bypass: Vulnerable [ 0.045263] debug: unmapping init [mem 0xffffffffb0e59000-0xffffffffb0e60fff] [ 0.047196] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz (family: 0x6, model: 0x3e, stepping: 0x4) [ 0.048641] Performance Events: IvyBridge events, full-width counters, Intel PMU driver. [ 0.049024] ... version: 2 [ 0.050011] ... bit width: 48 [ 0.051017] ... generic registers: 4 [ 0.052015] ... value mask: 0000ffffffffffff [ 0.053016] ... max period: 00007fffffffffff [ 0.054018] ... fixed-purpose events: 3 [ 0.055013] ... event mask: 000000070000000f [ 0.056349] rcu: Hierarchical SRCU implementation. [ 0.058545] smp: Bringing up secondary CPUs ... [ 0.059589] x86: Booting SMP configuration: [ 0.060034] .... node #0, CPUs: #1 #2 #3 [ 0.064090] smp: Brought up 1 node, 4 CPUs [ 0.066014] smpboot: Max logical packages: 1 [ 0.067018] smpboot: Total of 4 processors activated (19199.98 BogoMIPS) [ 0.141175] node 0 deferred pages initialised in 72ms [ 0.144515] devtmpfs: initialized [ 0.146421] x86/mm: Memory block size: 128MB [ 0.151566] gcov: version magic: 0x41383552 [ 0.156337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.161137] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc) [ 0.164375] pinctrl core: initialized pinctrl subsystem [ 0.168213] [ 0.168922] ************************************************************* [ 0.172020] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.175018] ** ** [ 0.178029] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.181013] ** ** [ 0.184013] ** This means that this kernel is built to expose internal ** [ 0.187013] ** IOMMU data structures, which may compromise security on ** [ 0.189012] ** your system. ** [ 0.192015] ** ** [ 0.195014] ** If you see this message and you are not debugging the ** [ 0.197014] ** kernel, report this immediately to your vendor! ** [ 0.200015] ** ** [ 0.202015] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.206015] ************************************************************* [ 0.210996] NET: Registered protocol family 16 [ 0.213450] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.215130] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.218068] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.222017] cpuidle: using governor menu [ 0.224023] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.227444] PCI: Using configuration type 1 for base access [ 0.229126] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on [ 0.241115] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.244012] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.250032] cryptd: max_cpu_qlen set to 1000 [ 0.253272] ACPI: Added _OSI(Module Device) [ 0.254015] ACPI: Added _OSI(Processor Device) [ 0.256013] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.257011] ACPI: Added _OSI(Processor Aggregator Device) [ 0.262657] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 0.269472] ACPI: Interpreter enabled [ 0.271065] ACPI: PM: (supports S0 S3 S4 S5) [ 0.272013] ACPI: Using IOAPIC for interrupt routing [ 0.274190] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.277428] ACPI: Enabled 2 GPEs in block 00 to 0F [ 0.289000] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.291060] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI HPX-Type3] [ 0.294021] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI] [ 0.297124] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.303760] acpiphp: Slot [2] registered [ 0.305147] acpiphp: Slot [5] registered [ 0.307121] acpiphp: Slot [6] registered [ 0.309121] acpiphp: Slot [3] registered [ 0.310095] acpiphp: Slot [4] registered [ 0.312141] acpiphp: Slot [7] registered [ 0.313100] acpiphp: Slot [8] registered [ 0.315156] acpiphp: Slot [9] registered [ 0.316102] acpiphp: Slot [10] registered [ 0.318099] acpiphp: Slot [11] registered [ 0.319152] acpiphp: Slot [12] registered [ 0.321145] acpiphp: Slot [13] registered [ 0.322082] acpiphp: Slot [14] registered [ 0.323125] acpiphp: Slot [15] registered [ 0.325107] acpiphp: Slot [16] registered [ 0.327114] acpiphp: Slot [17] registered [ 0.328092] acpiphp: Slot [18] registered [ 0.330085] acpiphp: Slot [19] registered [ 0.331103] acpiphp: Slot [20] registered [ 0.332121] acpiphp: Slot [21] registered [ 0.334119] acpiphp: Slot [22] registered [ 0.336151] acpiphp: Slot [23] registered [ 0.337093] acpiphp: Slot [24] registered [ 0.339199] acpiphp: Slot [25] registered [ 0.341136] acpiphp: Slot [26] registered [ 0.343139] acpiphp: Slot [27] registered [ 0.345118] acpiphp: Slot [28] registered [ 0.347123] acpiphp: Slot [29] registered [ 0.349135] acpiphp: Slot [30] registered [ 0.351116] acpiphp: Slot [31] registered [ 0.352065] PCI host bridge to bus 0000:00 [ 0.354023] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.356024] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.358026] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.361034] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.364030] pci_bus 0000:00: root bus resource [mem 0xe0000000000-0xe007fffffff window] [ 0.367033] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.370193] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.374209] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.377364] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.385013] pci 0000:00:01.1: reg 0x20: [io 0xc120-0xc12f] [ 0.389057] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.391018] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.393014] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.395029] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.397570] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.401799] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI [ 0.405044] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB [ 0.408013] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 [ 0.412000] pci 0000:00:02.0: reg 0x10: [io 0xc100-0xc11f] [ 0.420895] pci 0000:00:02.0: reg 0x20: [mem 0xe0000000000-0xe0000003fff 64bit pref] [ 0.426019] pci 0000:00:02.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref] [ 0.431900] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.435907] pci 0000:00:05.0: reg 0x10: [io 0xc000-0xc07f] [ 0.442018] pci 0000:00:05.0: reg 0x14: [mem 0xfebc0000-0xfebc0fff] [ 0.465019] pci 0000:00:05.0: reg 0x20: [mem 0xe0000004000-0xe0000007fff 64bit pref] [ 0.473752] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.480014] pci 0000:00:06.0: reg 0x10: [io 0xc080-0xc0ff] [ 0.486017] pci 0000:00:06.0: reg 0x14: [mem 0xfebc1000-0xfebc1fff] [ 0.504017] pci 0000:00:06.0: reg 0x20: [mem 0xe0000008000-0xe000000bfff 64bit pref] [ 0.516163] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.518321] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 0.519316] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 0.521384] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 0.523167] ACPI: PCI: Interrupt link LNKS configured for IRQ 9 [ 0.528101] iommu: Default domain type: Passthrough [ 0.529450] SCSI subsystem initialized [ 0.531134] ACPI: bus type USB registered [ 0.532097] usbcore: registered new interface driver usbfs [ 0.534058] usbcore: registered new interface driver hub [ 0.535086] usbcore: registered new device driver usb [ 0.537141] pps_core: LinuxPPS API ver. 1 registered [ 0.538008] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.541066] PTP clock support registered [ 0.543095] EDAC MC: Ver: 3.0.0 [ 0.545146] PCI: Using ACPI for IRQ routing [ 0.546667] NetLabel: Initializing [ 0.548011] NetLabel: domain hash size = 128 [ 0.549007] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.550075] NetLabel: unlabeled traffic allowed by default [ 0.552137] vgaarb: loaded [ 0.553246] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.555012] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.560717] clocksource: Switched to clocksource kvm-clock [ 0.665779] VFS: Disk quotas dquot_6.6.0 [ 0.667227] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.670035] *** VALIDATE ramfs *** [ 0.671151] *** VALIDATE hugetlbfs *** [ 0.672492] pnp: PnP ACPI init [ 0.674654] pnp: PnP ACPI: found 6 devices [ 0.698684] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.701567] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.703607] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.705495] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.707710] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.710127] pci_bus 0000:00: resource 8 [mem 0xe0000000000-0xe007fffffff window] [ 0.712759] NET: Registered protocol family 2 [ 0.714911] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc) [ 0.719422] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, vmalloc) [ 0.722986] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc) [ 0.727658] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc) [ 0.730876] TCP: Hash tables configured (established 65536 bind 65536) [ 0.733551] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, vmalloc) [ 0.736836] UDP hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.739671] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.742698] NET: Registered protocol family 1 [ 0.745091] RPC: Registered named UNIX socket transport module. [ 0.746889] RPC: Registered udp transport module. [ 0.748760] RPC: Registered tcp transport module. [ 0.750408] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.752868] NET: Registered protocol family 44 [ 0.754426] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.755875] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.757078] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.759039] PCI: CLS 0 bytes, default 64 [ 0.762275] Unpacking initramfs... [ 2.158747] debug: unmapping init [mem 0xffff8cb1fcc64000-0xffff8cb1fffcffff] [ 2.162835] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 2.165285] software IO TLB: mapped [mem 0x00000000a8000000-0x00000000ac000000] (64MB) [ 2.167516] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 2.653091] Initialise system trusted keyrings [ 2.655032] Key type blacklist registered [ 2.656970] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 2.668255] zbud: loaded [ 2.671200] *** VALIDATE nfs *** [ 2.672265] *** VALIDATE nfs4 *** [ 2.673627] pstore: using deflate compression [ 2.676721] Platform Keyring initialized [ 2.763660] NET: Registered protocol family 38 [ 2.765973] Key type asymmetric registered [ 2.768017] Asymmetric key parser 'x509' registered [ 2.770198] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.773410] io scheduler mq-deadline registered [ 2.775131] io scheduler kyber registered [ 2.776973] io scheduler bfq registered [ 2.778577] atomic64_test: passed for x86-64 platform with CX8 and with SSE [ 2.781593] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.784601] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 2.787835] ACPI: Power Button [PWRF] [ 2.792872] ACPI: \_SB_.LNKB: Enabled at IRQ 10 [ 2.799585] ACPI: \_SB_.LNKA: Enabled at IRQ 11 [ 2.816936] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.843818] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.873392] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.878325] Non-volatile memory driver v1.3 [ 2.879798] Linux agpgart interface v0.103 [ 2.913704] virtio_blk virtio1: [vda] 147088 512-byte logical blocks (75.3 MB/71.8 MiB) [ 2.916882] vda: detected capacity change from 0 to 75309056 [ 2.931156] virtio_blk virtio2: [vdb] 2097152 512-byte logical blocks (1.07 GB/1.00 GiB) [ 2.932965] vdb: detected capacity change from 0 to 1073741824 [ 2.940411] libphy: Fixed MDIO Bus: probed [ 2.944537] usbcore: registered new interface driver usbserial_generic [ 2.945853] usbserial: USB Serial support registered for generic [ 2.947434] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 2.950892] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.952127] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.953973] mousedev: PS/2 mouse device common for all mice [ 2.956803] rtc_cmos 00:05: RTC can wake from S4 [ 2.959711] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 2.960073] rtc_cmos 00:05: registered as rtc0 [ 2.964612] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs [ 2.965537] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input4 [ 2.968051] intel_pstate: CPU model not supported [ 2.973529] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input3 [ 2.978346] hid: raw HID events driver (C) Jiri Kosina [ 2.980759] usbcore: registered new interface driver usbhid [ 2.982403] usbhid: USB HID core driver [ 2.984645] drop_monitor: Initializing network drop monitor service [ 2.986931] Initializing XFRM netlink socket [ 2.988773] NET: Registered protocol family 10 [ 2.991588] Segment Routing with IPv6 [ 2.993069] NET: Registered protocol family 17 [ 2.995341] mpls_gso: MPLS GSO support [ 3.001209] RAS: Correctable Errors collector initialized. [ 3.003170] AVX version of gcm_enc/dec engaged. [ 3.004710] AES CTR mode by8 optimization enabled [ 3.085459] sched_clock: Marking stable (3085372825, 0)->(4006070343, -920697518) [ 3.088501] registered taskstats version 1 [ 3.091428] Loading compiled-in X.509 certificates [ 3.092943] zswap: loaded using pool lzo/zbud [ 3.117762] Key type big_key registered [ 3.130790] Key type encrypted registered [ 3.132194] ima: No TPM chip found, activating TPM-bypass! [ 3.134317] ima: Allocated hash algorithm: sha1 [ 3.135851] ima: No architecture policies found [ 3.137449] evm: Initialising EVM extended attributes: [ 3.139146] evm: security.selinux [ 3.140666] evm: security.ima [ 3.141696] evm: security.capability [ 3.142835] evm: HMAC attrs: 0x1 [ 3.145249] rtc_cmos 00:05: setting system clock to 2026-08-27 19:59:30 UTC (1787860770) [ 3.151531] debug: unmapping init [mem 0xffffffffb1e03000-0xffffffffb1ffffff] [ 3.154442] debug: unmapping init [mem 0xffffffffb0b82000-0xffffffffb0e58fff] [ 3.162342] Write protecting the kernel read-only data: 28672k [ 3.165961] debug: unmapping init [mem 0xffffffffaf203000-0xffffffffaf3fffff] [ 3.168328] debug: unmapping init [mem 0xffffffffafb14000-0xffffffffafbfffff] [ 3.201295] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 3.209737] systemd[1]: Detected virtualization kvm. [ 3.211418] systemd[1]: Detected architecture x86-64. [ 3.214697] systemd[1]: Running in initial RAM disk. Welcome to Rocky Linux 8.10 (Green Obsidian) dracut-049-233.git20240115.el8 (Initramfs)! [ 3.246269] systemd[1]: No hostname configured. [ 3.247842] systemd[1]: Set hostname to . [ 3.249993] random: systemd: uninitialized urandom read (16 bytes read) [ 3.252282] systemd[1]: Initializing machine ID from random generator. [ 3.296978] random: ln: uninitialized urandom read (6 bytes read) [ 3.371407] random: systemd: uninitialized urandom read (16 bytes read) [ 3.374949] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 3.382223] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 3.387477] systemd[1]: Reached target Initrd Root Device. [ OK ] Reached target Initrd Root Device. Starting Journal Service... [ OK ] Started Memstrack Anylazing Service. [ OK ] Reached target Local File Systems. [ OK ] Reached target Timers. [ OK ] Reached target Swap. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Slices. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Reached target Local Encrypted Volumes. Starting Apply Kernel Variables... Starting Setup Virtual Console... Starting Create Volatile Files and Directories... [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Sockets. [ OK ] Started Journal Service. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Apply Kernel Variables. [ OK ] Started Setup Virtual Console. [ OK ] Started Create Volatile Files and Directories. Starting dracut cmdline hook... Starting Create Static Device Nodes in /dev... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started dracut cmdline hook. Starting dracut pre-udev hook... [ 4.089161] device-mapper: uevent: version 1.0.3 [ 4.091360] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ OK ] Started dracut pre-udev hook. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook. Starting udev Coldplug all Devices... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started udev Coldplug all Devices. Starting dracut initqueue hook... [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 4.780663] random: fast init done [ 4.843480] virtio_net virtio0 ens2: renamed from eth0 [ 4.941652] scsi host0: ata_piix [ 5.065349] scsi host1: ata_piix [ 5.067468] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc120 irq 14 [ 5.071158] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc128 irq 15 [ 8.738112] dracut-initqueue[578]: RTNETLINK answers: File exists [ 9.648398] random: crng init done [ 9.649781] random: 7 urandom warning(s) missed due to ratelimiting Starting nbd nbd0... [ OK ] Started nbd nbd0. [ OK ] Started dracut initqueue hook. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting /sysroot... [ 10.166282] EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /sysroot. [ OK ] Reached target Initrd Root File System. Starting Reload Configuration from the Real Root... [ OK ] Started Reload Configuration from the Real Root. [ OK ] Reached target Initrd File Systems. [ OK ] Reached target Initrd Default Target. Starting dracut pre-pivot and cleanup hook... [ OK ] Started dracut pre-pivot and cleanup hook. Starting Cleaning Up and Shutting Down Daemons... [ OK ] Stopped dracut pre-pivot and cleanup hook. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). Stopping Hardware RNG Entropy Gatherer Daemon... [ OK ] Stopped target Timers. [ OK ] Stopped target Initrd Default Target. [ OK ] Stopped target Initrd Root Device. [ OK ] Stopped dracut initqueue hook. [ OK ] Stopped Hardware RNG Entropy Gatherer Daemon. [ OK ] Stopped target Basic System. [ OK ] Stopped target Paths. [ OK ] Stopped target Sockets. [ OK ] Stopped target Slices. [ OK ] Stopped target System Initialization. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped udev Coldplug all Devices. [ OK ] Stopped dracut pre-trigger hook. Stopping udev Kernel Device Manager... [ OK ] Stopped target Swap. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. [ OK ] Stopped udev Kernel Device Manager. [ OK ] Started Cleaning Up and Shutting Down Daemons. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create list of required sta…vice nodes for the current kernel. [ OK ] Stopped dracut pre-udev hook. [ OK ] Stopped dracut cmdline hook. [ OK ] Closed udev Control Socket. [ OK ] Closed udev Kernel Socket. Starting Cleanup udevd DB... [ OK ] Started Cleanup udevd DB. [ OK ] Reached target Switch Root. Starting Switch Root... [ 11.457193] printk: systemd: 17 output lines suppressed due to ratelimiting [ 11.709821] SELinux: Disabled at runtime. [ 11.768454] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 11.777324] systemd[1]: Detected virtualization kvm. [ 11.779475] systemd[1]: Detected architecture x86-64. Welcome to Rocky Linux 8.10 (Green Obsidian)! [ 12.327612] systemd[1]: initrd-switch-root.service: Succeeded. [ 12.347861] systemd[1]: Stopped Switch Root. [ OK ] Stopped Switch Root. [ 12.355810] systemd[1]: systemd-journald.service: Service has no hold-off time (RestartSec=0), scheduling restart. [ 12.360228] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1. [ 12.364440] systemd[1]: Stopped Journal Service. [ OK ] Stopped Journal Service. [ 12.374261] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.378770] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on initctl Compatibility Named Pipe. Mounting Huge Pages File System... Mounting Kernel Debug File System... Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target RPC Port Mapper. Starting Create list of required st…ce nodes for the current kernel... Mounting POSIX Message Queue File System... Activating swap /dev/disk/by-label/SWAP... [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting Apply Kernel Variables... [ OK ] Created slice system-sshd\x2dkeygen.slice. [ 12.524053] Adding 1048572k swap on /dev/vdb. Priority:-2 extents:1 across:1048572k FS [FAILED] Failed to set up automount Arbitrar…rmats File System Automount Point. See 'systemctl status proc-sys-fs-binfmt_misc.automount' for details. [ OK ] Reached target Slices. [ OK ] Stopped target Switch Root. [ OK ] Stopped target Initrd File Systems. [ OK ] Stopped target Initrd Root File System. [ OK ] Reached target rpc_pipefs.target. [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... [ OK ] Listening on Process Core Dump Socket. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Kernel Debug File System. [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Activated swap /dev/disk/by-label/SWAP. [ OK ] Started Apply Kernel Variables. [ OK ] Reached target Swap. Starting Configure read-only root support... Starting Create Static Device Nodes in /dev... Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /home/green/git/lustre-release... Mounting /mnt... [ OK ] Mounted /mnt. [ 12.918165] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ OK ] Started udev Coldplug all Devices. [ OK ] Mounted /home/green/git/lustre-release. [ OK ] Started udev Kernel Device Manager. [ 13.292439] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0 [ 13.322379] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 13.413951] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer [ 13.435233] EDAC sbridge: Ver: 1.1.2 [ 14.900411] Key type dns_resolver registered [ 15.214400] NFS: Registering the id_resolver key type [ 15.216687] Key type id_resolver registered [ 15.218407] Key type id_legacy registered [ OK ] Started Configure read-only root support. [ OK ] Reached target Local File Systems. Starting Mark the need to relabel after reboot... Starting Rebuild Dynamic Linker Cache... Starting Load/Save Random Seed... Starting Create Volatile Files and Directories... [ OK ] Started Mark the need to relabel after reboot. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting RPC Bind... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC Bind. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Started dnf makecache --timer. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started daily update of the root trust anchor for DNSSEC. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Network Manager... Starting Login Service... Starting Restore /run/initramfs on shutdown... [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started irqbalance daemon. [ OK ] Reached target sshd-keygen.target. [ OK ] Started Restore /run/initramfs on shutdown. [ OK ] Started Login Service. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting Dynamic System Tuning Daemon... Starting OpenSSH server daemon... Starting GSSAPI Proxy Daemon... Starting Network Manager Wait Online... Starting Hostname Service... [ OK ] Started OpenSSH server daemon. [ OK ] Started GSSAPI Proxy Daemon. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Command Scheduler. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Serial Getty on ttyS1. [ OK ] Reached target Login Prompts. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting Notify NFS peers of a restart... Starting Crash recovery kernel arming... Starting System Logging Service... [ OK ] Started Notify NFS peers of a restart. [ OK ] Started System Logging Service. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Started Dynamic System Tuning Daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Rocky Linux 8.10 (Green Obsidian) Kernel 4.18.0rh8.10-debug on an x86_64 oleg458-client login: [ 73.242956] libcfs: loading out-of-tree module taints kernel. [ 73.427095] Key type ._llcrypt registered [ 73.433273] Key type .llcrypt registered [ 74.465982] libcfs: HW NUMA nodes: 1, HW CPU cores: 4, npartitions: 2 [ 74.483947] alg: No test for adler32 (adler32-zlib) [ 76.337598] Lustre: Lustre: Build Version: 2.17.57_120_gb73d7ca [ 77.809667] LNet: Added LNI 192.168.204.58@tcp [8/256/0/180] [ 79.664431] Key type lgssc registered [ 82.088588] Lustre: Echo OBD driver; http://www.lustre.org/ [ 150.522018] hrtimer: interrupt took 3019911 ns [ 234.176477] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 239.501349] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 252.047393] Lustre: DEBUG MARKER: oleg458-client.virtnet: executing check_logdir /tmp/testlogs/ [ 257.618938] Lustre: DEBUG MARKER: oleg458-client.virtnet: executing yml_node [ 260.064939] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 262.756102] Lustre: DEBUG MARKER: Client: 2.17.57.120 [ 265.420950] Lustre: DEBUG MARKER: MDS: 2.17.57.120 [ 267.998667] Lustre: DEBUG MARKER: OSS: 2.17.57.120 [ 269.702612] Lustre: DEBUG MARKER: -----============= acceptance-small: sanity-sec ============----- Thu Aug 27 16:03:55 EDT 2026 [ 287.548588] Lustre: DEBUG MARKER: excepting tests: 27 66 [ 288.877681] Lustre: DEBUG MARKER: skipping tests SLOW=no: 26 [ 291.570129] Lustre: DEBUG MARKER: === sanity-sec: start setup 16:04:17 (1787861057) === [ 297.196234] Lustre: DEBUG MARKER: oleg458-client.virtnet: executing check_config_client /mnt/lustre [ 316.982294] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 329.721517] Lustre: DEBUG MARKER: === sanity-sec: finish setup 16:04:55 (1787861095) === [ 337.008883] Lustre: DEBUG MARKER: == sanity-sec test 0: uid permission ======================================================================================= 16:05:02 (1787861102) [ 346.781638] Lustre: DEBUG MARKER: == sanity-sec test 1: setuid/gid ======================================================================================= 16:05:12 (1787861112) [ 348.500654] Lustre: DEBUG MARKER: SKIP: sanity-sec test_1 without GSS support. [ 350.496345] Lustre: DEBUG MARKER: == sanity-sec test 4: set supplementary group ========================================================================= 16:05:16 (1787861116) [ 362.463333] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 362.475942] Lustre: Skipped 1 previous similar message [ 363.434895] Lustre: DEBUG MARKER: == sanity-sec test 5: Test l_getidentity with a nonexistent user on the MDT ========================================================== 16:05:28 (1787861128) [ 386.339197] Lustre: DEBUG MARKER: == sanity-sec test 7: nodemap create and delete ========== 16:05:52 (1787861152) [ 414.957973] Lustre: DEBUG MARKER: == sanity-sec test 8: nodemap reject duplicates ========== 16:06:20 (1787861180) [ 456.428258] Lustre: DEBUG MARKER: == sanity-sec test 9: nodemap range add ================== 16:07:02 (1787861222) [ 501.309214] Lustre: DEBUG MARKER: == sanity-sec test 10a: nodemap reject duplicate ranges == 16:07:46 (1787861266) [ 549.878105] Lustre: DEBUG MARKER: == sanity-sec test 10b: delete range from the correct nodemap ========================================================== 16:08:35 (1787861315) [ 566.274803] Lustre: DEBUG MARKER: == sanity-sec test 10c: verfify contiguous range support ========================================================== 16:08:52 (1787861332) [ 579.658713] Lustre: DEBUG MARKER: == sanity-sec test 10d: verfify nodemap range format '*@' support ========================================================== 16:09:05 (1787861345) [ 592.296598] Lustre: DEBUG MARKER: == sanity-sec test 11: nodemap modify ==================== 16:09:18 (1787861358) [ 637.194628] Lustre: DEBUG MARKER: == sanity-sec test 12: nodemap set squash ids ============ 16:10:02 (1787861402) [ 683.881616] Lustre: DEBUG MARKER: == sanity-sec test 13: test nids ========================= 16:10:49 (1787861449) [ 737.871535] Lustre: DEBUG MARKER: == sanity-sec test 14: test default nodemap nid lookup === 16:11:43 (1787861503) [ 788.935977] Lustre: DEBUG MARKER: == sanity-sec test 15: test id mapping =================== 16:12:34 (1787861554) [ 956.696933] Lustre: DEBUG MARKER: == sanity-sec test 16: test nodemap all_off fileops ====== 16:15:22 (1787861722) [ 1063.907766] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 1063.913797] Lustre: Skipped 1 previous similar message [ 1115.103299] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 1166.309240] Lustre: lustre-OST0001-osc-ffff8cb244e5f800: disconnect after 20s idle [ 1212.394311] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 20s idle [ 1218.558986] Lustre: DEBUG MARKER: == sanity-sec test 17: test nodemap trusted_noadmin fileops ========================================================== 16:19:44 (1787861984) [ 1335.268165] Lustre: lustre-OST0001-osc-ffff8cb244e5f800: disconnect after 24s idle [ 1335.286339] Lustre: Skipped 1 previous similar message [ 1396.703287] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 25s idle [ 1463.264965] Lustre: lustre-OST0001-osc-ffff8cb244e5f800: disconnect after 20s idle [ 1463.282378] Lustre: Skipped 1 previous similar message [ 1519.590855] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 1591.268174] Lustre: lustre-OST0001-osc-ffff8cb244e5f800: disconnect after 21s idle [ 1591.273172] Lustre: Skipped 1 previous similar message [ 1775.190853] Lustre: DEBUG MARKER: == sanity-sec test 18: test nodemap mapped_noadmin fileops ========================================================== 16:29:01 (1787862541) [ 1780.705874] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 25s idle [ 1780.715765] Lustre: Skipped 3 previous similar messages [ 2066.222484] Lustre: DEBUG MARKER: == sanity-sec test 19: test nodemap trusted_admin fileops ========================================================== 16:33:52 (1787862832) [ 2072.543491] Lustre: lustre-OST0000-osc-ffff8cb244e5f800: disconnect after 24s idle [ 2072.561910] Lustre: Skipped 6 previous similar messages [ 2254.202696] Lustre: DEBUG MARKER: == sanity-sec test 20: test nodemap mapped_admin fileops ========================================================== 16:37:00 (1787863020) [ 2441.785469] Lustre: DEBUG MARKER: == sanity-sec test 21: test nodemap mapped_trusted_noadmin fileops ========================================================== 16:40:07 (1787863207) [ 2610.143756] Lustre: lustre-OST0001-osc-ffff8cb244e5f800: disconnect after 24s idle [ 2610.155230] Lustre: Skipped 8 previous similar messages [ 2727.772040] Lustre: DEBUG MARKER: == sanity-sec test 22: test nodemap mapped_trusted_admin fileops ========================================================== 16:44:53 (1787863493) [ 2897.078349] Lustre: DEBUG MARKER: == sanity-sec test 23a: test mapped regular ACLs ========= 16:47:43 (1787863663) [ 2898.420898] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23a Need 2 clients at least [ 2900.029525] Lustre: DEBUG MARKER: == sanity-sec test 23b: test mapped default ACLs ========= 16:47:46 (1787863666) [ 2901.597382] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23b Need 2 clients at least [ 2903.280869] Lustre: DEBUG MARKER: == sanity-sec test 24: check nodemap proc files for LBUGs and Oopses ========================================================== 16:47:49 (1787863669) [ 2936.652808] Lustre: DEBUG MARKER: == sanity-sec test 25a: test save and reload nodemap config ========================================================== 16:48:22 (1787863702) [ 2939.305522] Lustre: Unmounted lustre-client [ 2971.081907] Lustre: DEBUG MARKER: === sanity-sec: start setup 16:48:57 (1787863737) === [ 3007.999219] LustreError: 63712:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1237us [ 3008.052162] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3013.588405] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 3022.513531] Lustre: DEBUG MARKER: === sanity-sec: finish setup 16:49:48 (1787863788) === [ 3024.131806] Lustre: Unmounted lustre-client [ 3035.477239] LustreError: 64789:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2703us [ 3035.550322] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3041.803837] Lustre: DEBUG MARKER: == sanity-sec test 25b: test nodemap info values ========= 16:50:07 (1787863807) [ 3090.626626] Lustre: DEBUG MARKER: == sanity-sec test 25c: test yaml-compliance for nodemap ========================================================== 16:50:56 (1787863856) [ 3120.760732] Lustre: Unmounted lustre-client [ 3121.205763] LustreError: 67072:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 423us [ 3121.287730] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3131.891335] Lustre: Unmounted lustre-client [ 3143.569596] LustreError: 67751:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2038us [ 3143.635976] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3145.609905] Lustre: DEBUG MARKER: SKIP: sanity-sec test_26 skipping SLOW test 26 [ 3147.818887] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27a skipping excluded test 27a (base 27) [ 3150.128444] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27aa skipping excluded test 27aa (base 27) [ 3152.553339] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ab skipping excluded test 27ab (base 27) [ 3154.346098] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ac skipping excluded test 27ac (base 27) [ 3156.209285] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ad skipping excluded test 27ad (base 27) [ 3158.257825] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27b skipping excluded test 27b (base 27) [ 3160.230723] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27c skipping excluded test 27c (base 27) [ 3161.991788] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27d skipping excluded test 27d (base 27) [ 3163.909884] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27e skipping excluded test 27e (base 27) [ 3165.772642] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27f skipping excluded test 27f (base 27) [ 3167.632094] Lustre: DEBUG MARKER: == sanity-sec test 28: check shared key rotation method == 16:52:13 (1787863933) [ 3169.246982] Lustre: DEBUG MARKER: SKIP: sanity-sec test_28 need shared key feature for this test [ 3171.534859] Lustre: DEBUG MARKER: == sanity-sec test 29: check for missing shared key ====== 16:52:16 (1787863936) [ 3173.466236] Lustre: DEBUG MARKER: SKIP: sanity-sec test_29 need shared key feature for this test [ 3176.011509] Lustre: DEBUG MARKER: == sanity-sec test 30: check for invalid shared key ====== 16:52:21 (1787863941) [ 3178.279618] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30 need shared key feature for this test [ 3180.420968] Lustre: DEBUG MARKER: == sanity-sec test 30b: basic test of all different SSK flavors ========================================================== 16:52:25 (1787863945) [ 3182.382563] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30b need shared key feature for this test [ 3184.476651] Lustre: DEBUG MARKER: == sanity-sec test 31: client mount option '-o network' == 16:52:30 (1787863950) [ 3187.470414] Lustre: DEBUG MARKER: SKIP: sanity-sec test_31 without lnetctl support. [ 3189.736501] Lustre: DEBUG MARKER: == sanity-sec test 32: check for mgssec ================== 16:52:35 (1787863955) [ 3193.014938] Lustre: DEBUG MARKER: SKIP: sanity-sec test_32 need shared key feature for this test [ 3195.330559] Lustre: DEBUG MARKER: == sanity-sec test 33: correct srpc flags for MGS connection ========================================================== 16:52:40 (1787863960) [ 3197.606927] Lustre: DEBUG MARKER: SKIP: sanity-sec test_33 need shared key feature for this test [ 3200.418543] Lustre: DEBUG MARKER: == sanity-sec test 34: deny_unknown on default nodemap === 16:52:45 (1787863965) [ 3227.802739] Lustre: DEBUG MARKER: == sanity-sec test 35: Check permissions when accessing changelogs ========================================================== 16:53:13 (1787863993) [ 3257.445238] LustreError: 72958:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff8cb2588c5800: fail to open changelog catalog: rc = -13 [ 3270.123597] Lustre: DEBUG MARKER: == sanity-sec test 36: control if clients can use encryption ========================================================== 16:53:55 (1787864035) [ 3272.020540] Lustre: Unmounted lustre-client [ 3272.354375] LustreError: 73375:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 6820us [ 3272.408825] Lustre: Test dummy encryption mode enabled [ 3272.423817] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3272.633090] llcrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-aesni)" [ 3279.189837] Lustre: Test dummy encryption mode enabled [ 3281.106128] Lustre: Unmounted lustre-client [ 3281.111532] Lustre: Skipped 1 previous similar message [ 3285.150644] LustreError: 73688:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 4942us [ 3285.177128] LustreError: 73688:0:(obd_config.c:1432:process_param2_config()) Skipped 1 previous similar message [ 3285.207900] Lustre: lustre-MDT0000-mdc-ffff8cb250ccc000: connection denied by lustre-MDT0000_UUID: rc = -13 [ 3285.218244] LustreError: 73663:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff8cb250ccc000: can't stat MDS #0: rc = -13 [ 3285.248621] LustreError: 73663:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -13 [ 3304.816418] LustreError: 74392:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 9599us [ 3304.888341] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3304.898221] Lustre: Skipped 1 previous similar message [ 3307.085402] Lustre: Unmounted lustre-client [ 3307.086882] Lustre: Skipped 1 previous similar message [ 3308.523816] bash (73169): drop_caches: 3 [ 3311.782768] Lustre: DEBUG MARKER: == sanity-sec test 37: simple encrypted file ============= 16:54:36 (1787864076) [ 3314.083275] Lustre: DEBUG MARKER: SKIP: sanity-sec test_37 ldiskfs only test (using debugfs) [ 3315.834205] Lustre: DEBUG MARKER: == sanity-sec test 38: encrypted file with hole ========== 16:54:41 (1787864081) [ 3317.429288] Lustre: DEBUG MARKER: SKIP: sanity-sec test_38 skip ZFS backend [ 3319.559692] Lustre: DEBUG MARKER: == sanity-sec test 39: rewrite data in already encrypted page ========================================================== 16:54:45 (1787864085) [ 3322.562816] Lustre: Test dummy encryption mode enabled [ 3322.574420] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3322.578966] Lustre: Skipped 1 previous similar message [ 3323.077955] llcrypt: AES-256-XTS using implementation "xts-aes-aesni" [ 3333.214940] bash (75100): drop_caches: 3 [ 3336.639905] Lustre: DEBUG MARKER: == sanity-sec test 40: exercise size of encrypted file === 16:55:01 (1787864101) [ 3339.530110] Lustre: Unmounted lustre-client [ 3339.532869] Lustre: Skipped 2 previous similar messages [ 3339.945532] LustreError: 76074:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 17434us [ 3339.960148] LustreError: 76074:0:(obd_config.c:1432:process_param2_config()) Skipped 3 previous similar messages [ 3339.994058] Lustre: Test dummy encryption mode enabled [ 3347.525226] bash (75868): drop_caches: 3 [ 3359.090371] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3359.102745] Lustre: Skipped 3 previous similar messages [ 3359.699925] bash (75868): drop_caches: 3 [ 3362.957588] Lustre: DEBUG MARKER: == sanity-sec test 41: test race on encrypted file size (1) ========================================================== 16:55:27 (1787864127) [ 3365.678904] Lustre: Test dummy encryption mode enabled [ 3393.715931] bash (76821): drop_caches: 3 [ 3396.732600] Lustre: DEBUG MARKER: == sanity-sec test 42: test race on encrypted file size (2) ========================================================== 16:56:01 (1787864161) [ 3400.065764] Lustre: Test dummy encryption mode enabled [ 3426.272106] Lustre: Unmounted lustre-client [ 3426.279945] Lustre: Skipped 5 previous similar messages [ 3426.672235] LustreError: 78388:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1122us [ 3426.696477] LustreError: 78388:0:(obd_config.c:1432:process_param2_config()) Skipped 6 previous similar messages [ 3426.766881] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3426.772289] Lustre: Skipped 4 previous similar messages [ 3430.047984] bash (77611): drop_caches: 3 [ 3432.841124] Lustre: DEBUG MARKER: == sanity-sec test 43: test race on encrypted file size (3) ========================================================== 16:56:38 (1787864198) [ 3435.808200] Lustre: Test dummy encryption mode enabled [ 3435.810064] Lustre: Skipped 1 previous similar message [ 3465.656714] bash (78453): drop_caches: 3 [ 3469.009692] Lustre: DEBUG MARKER: == sanity-sec test 44: encrypted file access semantics: direct IO ========================================================== 16:57:13 (1787864233) [ 3471.208738] Lustre: DEBUG MARKER: SKIP: sanity-sec test_44 This test needs vmtouch utility [ 3472.982332] Lustre: DEBUG MARKER: == sanity-sec test 45: encrypted file access semantics: MMAP ========================================================== 16:57:18 (1787864238) [ 3475.677115] Lustre: Test dummy encryption mode enabled [ 3475.683453] Lustre: Skipped 1 previous similar message [ 3485.466796] bash (79591): drop_caches: 3 [ 3488.646153] Lustre: DEBUG MARKER: == sanity-sec test 46: encrypted file access semantics without key ========================================================== 16:57:33 (1787864253) [ 3492.420366] bash (80361): drop_caches: 3 [ 3496.747530] bash (80361): drop_caches: 3 [ 3497.741659] LustreError: 80718:0:(llite_lib.c:4143:ll_prep_md_op_data()) lustre: failed to setup filename: rc = -126 [ 3506.223937] bash (80361): drop_caches: 3 [ 3508.706214] Lustre: DEBUG MARKER: == sanity-sec test 47: encrypted file access semantics: rename/link ========================================================== 16:57:54 (1787864274) [ 3519.961827] bash (81244): drop_caches: 3 [ 3547.430800] bash (81244): drop_caches: 3 [ 3554.585420] Lustre: Unmounted lustre-client [ 3554.589820] Lustre: Skipped 11 previous similar messages [ 3555.119731] LustreError: 82333:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 570us [ 3555.131100] LustreError: 82333:0:(obd_config.c:1432:process_param2_config()) Skipped 10 previous similar messages [ 3555.168328] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3555.175841] Lustre: Skipped 10 previous similar messages [ 3555.564871] bash (81244): drop_caches: 3 [ 3557.957525] Lustre: DEBUG MARKER: == sanity-sec test 48a: encrypted file access semantics: truncate ========================================================== 16:58:43 (1787864323) [ 3560.304833] Lustre: Test dummy encryption mode enabled [ 3560.309906] Lustre: Skipped 2 previous similar messages [ 3563.205267] bash (82376): drop_caches: 3 [ 3566.936787] bash (82376): drop_caches: 3 [ 3575.689521] bash (82376): drop_caches: 3 [ 3578.357765] Lustre: DEBUG MARKER: == sanity-sec test 48b: encrypted file: concurrent truncate ========================================================== 16:59:03 (1787864343) [ 3579.915381] Lustre: DEBUG MARKER: SKIP: sanity-sec test_48b Need at least 2 clients [ 3581.466273] Lustre: DEBUG MARKER: == sanity-sec test 49: Avoid getxattr for encryption context ========================================================== 16:59:07 (1787864347) [ 3584.452379] bash (83607): drop_caches: 3 [ 3585.068926] bash (83607): drop_caches: 3 [ 3586.351916] bash (83607): drop_caches: 3 [ 3587.293677] bash (83607): drop_caches: 3 [ 3590.461145] Lustre: DEBUG MARKER: SKIP: sanity-sec test_49 2nd part needs >= 2 MDTs [ 3618.676522] bash (83607): drop_caches: 3 [ 3621.672780] Lustre: DEBUG MARKER: == sanity-sec test 50: DoM encrypted file ================ 16:59:46 (1787864386) [ 3625.290640] bash (84612): drop_caches: 3 [ 3625.855223] bash (84612): drop_caches: 3 [ 3626.371507] Lustre: 84868:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3626.732536] bash (84612): drop_caches: 3 [ 3627.400944] bash (84612): drop_caches: 3 [ 3628.005734] Lustre: 84893:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3628.370993] bash (84612): drop_caches: 3 [ 3629.032495] bash (84612): drop_caches: 3 [ 3629.512984] Lustre: 84918:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3629.916550] bash (84612): drop_caches: 3 [ 3630.444727] bash (84612): drop_caches: 3 [ 3631.223538] bash (84612): drop_caches: 3 [ 3631.714275] bash (84612): drop_caches: 3 [ 3632.344536] Lustre: 84969:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3632.350197] Lustre: 84969:0:(file.c:676:ll_dom_finish_open()) Skipped 1 previous similar message [ 3632.747725] bash (84612): drop_caches: 3 [ 3633.266601] bash (84612): drop_caches: 3 [ 3634.070473] bash (84612): drop_caches: 3 [ 3634.569356] bash (84612): drop_caches: 3 [ 3635.354842] bash (84612): drop_caches: 3 [ 3635.899449] bash (84612): drop_caches: 3 [ 3637.189566] bash (84612): drop_caches: 3 [ 3637.893636] bash (84612): drop_caches: 3 [ 3639.158135] bash (84612): drop_caches: 3 [ 3639.725248] bash (84612): drop_caches: 3 [ 3640.804652] bash (84612): drop_caches: 3 [ 3641.305546] bash (84612): drop_caches: 3 [ 3641.781394] Lustre: 85121:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x3:0x0] with data: rc = -126 [ 3641.792518] Lustre: 85121:0:(file.c:676:ll_dom_finish_open()) Skipped 2 previous similar messages [ 3642.133551] bash (84612): drop_caches: 3 [ 3642.613398] bash (84612): drop_caches: 3 [ 3643.450874] bash (84612): drop_caches: 3 [ 3643.998620] bash (84612): drop_caches: 3 [ 3653.709789] bash (84612): drop_caches: 3 [ 3656.503471] Lustre: DEBUG MARKER: == sanity-sec test 51: FS capabilities =================== 17:00:21 (1787864421) [ 3707.998574] Lustre: DEBUG MARKER: == sanity-sec test 52: Mirrored encrypted file =========== 17:01:13 (1787864473) [ 3710.821326] Lustre: Test dummy encryption mode enabled [ 3710.825229] Lustre: Skipped 2 previous similar messages [ 3715.960877] LustreError: 87322:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff8cb26a171800: inode [0x200000412:0x4:0x0] mdc close failed: rc = -22 [ 3723.336645] bash (87037): drop_caches: 3 [ 3726.357660] Lustre: DEBUG MARKER: == sanity-sec test 53: Mixed PAGE_SIZE clients =========== 17:01:31 (1787864491) [ 3728.284107] Lustre: DEBUG MARKER: SKIP: sanity-sec test_53 Need 64K PAGE_SIZE client [ 3730.368523] Lustre: DEBUG MARKER: == sanity-sec test 54: Encryption policies with fscrypt == 17:01:35 (1787864495) [ 3732.128221] Lustre: DEBUG MARKER: SKIP: sanity-sec test_54 This test needs fscrypt userspace tool [ 3733.640486] Lustre: DEBUG MARKER: == sanity-sec test 55: access with seteuid =============== 17:01:39 (1787864499) [ 3769.350100] Lustre: DEBUG MARKER: == sanity-sec test 56: FIEMAP on encrypted file ========== 17:02:15 (1787864535) [ 3771.208340] Lustre: DEBUG MARKER: SKIP: sanity-sec test_56 skip ZFS backend [ 3772.924103] Lustre: DEBUG MARKER: == sanity-sec test 57: security.c/encryption.c xattr protection ========================================================== 17:02:18 (1787864538) [ 3774.599253] Lustre: DEBUG MARKER: SKIP: sanity-sec test_57 skip ZFS backend [ 3776.922557] Lustre: DEBUG MARKER: == sanity-sec test 58: access to enc file's xattrs ======= 17:02:22 (1787864542) [ 3778.211952] Lustre: DEBUG MARKER: SKIP: sanity-sec test_58 skip ZFS backend [ 3779.660420] Lustre: DEBUG MARKER: == sanity-sec test 59a: mirror resync of encrypted files without key ========================================================== 17:02:25 (1787864545) [ 3786.333252] bash (90432): drop_caches: 3 [ 3788.706632] bash (90432): drop_caches: 3 [ 3804.423735] bash (90432): drop_caches: 3 [ 3808.357467] Lustre: DEBUG MARKER: == sanity-sec test 59b: migrate/extend/split of encrypted files without key ========================================================== 17:02:52 (1787864572) [ 3811.954486] Lustre: Unmounted lustre-client [ 3811.959400] Lustre: Skipped 15 previous similar messages [ 3812.359977] LustreError: 91597:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 577us [ 3812.376578] LustreError: 91597:0:(obd_config.c:1432:process_param2_config()) Skipped 15 previous similar messages [ 3812.428912] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 3812.438090] Lustre: Skipped 15 previous similar messages [ 3816.554306] bash (91391): drop_caches: 3 [ 3818.491393] bash (91391): drop_caches: 3 [ 3826.297518] bash (91391): drop_caches: 3 [ 3828.652316] bash (91391): drop_caches: 3 [ 3839.695421] bash (91391): drop_caches: 3 [ 3840.489682] LustreError: 92121:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff8cb250aeb000: inode [0x200000416:0x2:0x0] mdc close failed: rc = -22 [ 3841.146203] bash (91391): drop_caches: 3 [ 3855.851563] bash (91391): drop_caches: 3 [ 3859.566227] Lustre: DEBUG MARKER: == sanity-sec test 59c: MDT migrate of encrypted files without key ========================================================== 17:03:43 (1787864623) [ 3861.633610] Lustre: DEBUG MARKER: SKIP: sanity-sec test_59c needs >= 2 MDTs [ 3863.188190] Lustre: DEBUG MARKER: == sanity-sec test 60: Subdirmount of encrypted dir ====== 17:03:49 (1787864629) [ 3866.938183] bash (93040): drop_caches: 3 [ 3871.389387] bash (93040): drop_caches: 3 [ 3886.323765] bash (93040): drop_caches: 3 [ 3890.096569] Lustre: DEBUG MARKER: == sanity-sec test 61: Nodemap enforces read-only mount == 17:04:14 (1787864654) [ 3924.255984] Lustre: lustre-MDT0000-mdc-ffff8cb243201800: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3924.273192] LustreError: 94636:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff8cb243201800: can't stat MDS #0: rc = -30 [ 3924.283352] LustreError: 94636:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff8cb243201800: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3927.555414] Lustre: lustre-MDT0000-mdc-ffff8cb252b91000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3927.565523] LustreError: 94719:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff8cb252b91000: can't stat MDS #0: rc = -30 [ 3927.582983] LustreError: 94719:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff8cb252b91000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3927.607499] LustreError: 2350:0:(lmv_obd.c:211:lmv_notify()) activation of lustre-MDT0000_UUID failed: -22 [ 3933.839262] Lustre: lustre-MDT0000-mdc-ffff8cb244535800: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3933.850396] LustreError: 94887:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff8cb244535800: can't stat MDS #0: rc = -30 [ 3933.856233] LustreError: 94887:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff8cb244535800: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3951.507643] Lustre: DEBUG MARKER: == sanity-sec test 62: e2fsck with encrypted files ======= 17:05:17 (1787864717) [ 3953.016657] Lustre: DEBUG MARKER: SKIP: sanity-sec test_62 skip ZFS backend [ 3954.716610] Lustre: DEBUG MARKER: == sanity-sec test 63: fid2path with encrypted files ===== 17:05:20 (1787864720) [ 3956.489473] Lustre: DEBUG MARKER: SKIP: sanity-sec test_63 This test needs fscrypt userspace tool [ 3958.342844] Lustre: DEBUG MARKER: == sanity-sec test 64a: Nodemap enforces file_perms RBAC roles ========================================================== 17:05:24 (1787864724) [ 4023.527820] Lustre: DEBUG MARKER: == sanity-sec test 64b: Nodemap enforces dne_ops RBAC roles ========================================================== 17:06:29 (1787864789) [ 4025.282984] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64b mdt count 1, skipping dne_ops role [ 4027.010667] Lustre: DEBUG MARKER: == sanity-sec test 64c: Nodemap enforces quota related RBAC roles ========================================================== 17:06:33 (1787864793) [ 4063.552291] LustreError: 98592:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff8cb246354000: ptlrpc_queue_wait failed: rc = -1 [ 4064.064831] LustreError: 98604:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff8cb246354000: ptlrpc_queue_wait failed: rc = -1 [ 4064.084337] LustreError: 98604:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 10 previous similar messages [ 4087.296559] LustreError: 98968:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff8cb246354000: ptlrpc_queue_wait failed: rc = -1 [ 4087.305820] LustreError: 98968:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 12 previous similar messages [ 4119.465598] Lustre: DEBUG MARKER: == sanity-sec test 64d: Nodemap enforces byfid_ops RBAC roles ========================================================== 17:08:04 (1787864884) [ 4183.363530] Lustre: DEBUG MARKER: == sanity-sec test 64e: Nodemap enforces chlg_ops RBAC roles ========================================================== 17:09:09 (1787864949) [ 4214.070318] LustreError: 101803:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff8cb246354000: fail to open changelog catalog: rc = -13 [ 4241.858212] LustreError: 102251:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff8cb246354000: fail to open changelog catalog: rc = -13 [ 4265.200406] Lustre: DEBUG MARKER: == sanity-sec test 64f: Nodemap enforces fscrypt_admin RBAC roles ========================================================== 17:10:30 (1787865030) [ 4266.797867] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64f Need fscrypt, skip fscrypt_admin role [ 4268.374162] Lustre: DEBUG MARKER: == sanity-sec test 64g: Nodemap enforces server_upcall RBAC role ========================================================== 17:10:34 (1787865034) [ 4331.987420] Lustre: DEBUG MARKER: == sanity-sec test 64h: Nodemap enforces local_admin RBAC roles ========================================================== 17:11:37 (1787865097) [ 4354.143747] LustreError: 105470:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff8cb246354000: ptlrpc_queue_wait failed: rc = -1 [ 4354.156056] LustreError: 105470:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 2 previous similar messages [ 4359.010152] LustreError: 105554:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff8cb246354000: ptlrpc_queue_wait failed: rc = -1 [ 4382.567385] Lustre: DEBUG MARKER: == sanity-sec test 64i: Nodemap quota enforcement with local_admin RBAC and offsets ========================================================== 17:12:28 (1787865148) [ 4584.963298] Lustre: Unmounted lustre-client [ 4584.968687] Lustre: Skipped 17 previous similar messages [ 4591.828133] LustreError: 110157:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2450us [ 4591.842743] LustreError: 110157:0:(obd_config.c:1432:process_param2_config()) Skipped 17 previous similar messages [ 4591.894365] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 4591.898519] Lustre: Skipped 17 previous similar messages [ 4595.218709] Lustre: DEBUG MARKER: == sanity-sec test 64j: Nodemap enforces projid_set RBAC role ========================================================== 17:16:00 (1787865360) [ 4668.723894] Lustre: DEBUG MARKER: == sanity-sec test 64k: Nodemap enforces foreign_ops RBAC roles ========================================================== 17:17:14 (1787865434) [ 4707.441956] Lustre: DEBUG MARKER: == sanity-sec test 64l: Nodemap enforces immutable_flags RBAC role ========================================================== 17:17:53 (1787865473) [ 4745.126908] Lustre: DEBUG MARKER: == sanity-sec test 65: lfs find -printf %La and --attrs support ========================================================== 17:18:31 (1787865511) [ 4748.595959] LustreError: 114299:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff8cb250cc8800: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4748.981981] Lustre: Test dummy encryption mode enabled [ 4748.989440] Lustre: Skipped 8 previous similar messages [ 4749.931494] LustreError: 114386:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff8cb243341000: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4761.499036] LustreError: 115059:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff8cb243341000: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4761.514984] LustreError: 115059:0:(file.c:251:ll_close_inode_openhandle()) Skipped 1 previous similar message [ 4762.776542] bash (114121): drop_caches: 3 [ 4766.246973] Lustre: DEBUG MARKER: == sanity-sec test 67: should not create compressed file on encrypted dir ========================================================== 17:18:51 (1787865531) [ 4767.988494] Lustre: DEBUG MARKER: SKIP: sanity-sec test_67 Need fscrypt [ 4770.045531] Lustre: DEBUG MARKER: == sanity-sec test 68: all config logs are processed ===== 17:18:55 (1787865535) [ 4773.078041] LustreError: 2350:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d sleeping for 20000ms [ 4778.207665] LustreError: 115628:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.204.158@tcp: failed processing log, type 1: rc = -110 [ 4793.167121] LustreError: 2350:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d awake [ 4807.334176] Lustre: DEBUG MARKER: == sanity-sec test 69: check upcall incorrect values ===== 17:19:33 (1787865573) [ 4821.543582] Lustre: DEBUG MARKER: == sanity-sec test 70: targets have local copy of sptlrpc llog ========================================================== 17:19:46 (1787865586) [ 4823.637321] Lustre: DEBUG MARKER: SKIP: sanity-sec test_70 need shared key feature for this test [ 4825.942996] Lustre: DEBUG MARKER: == sanity-sec test 71: encryption does not remove project flag ========================================================== 17:19:51 (1787865591) [ 4827.689711] Lustre: DEBUG MARKER: SKIP: sanity-sec test_71 Need fscrypt [ 4830.542556] Lustre: DEBUG MARKER: == sanity-sec test 72a: dynamic nodemap properties on OSS ========================================================== 17:19:55 (1787865595) [ 4925.212754] Lustre: DEBUG MARKER: == sanity-sec test 72b: dynamic nodemap properties on MDS ========================================================== 17:21:31 (1787865691) [ 5010.272966] Lustre: DEBUG MARKER: == sanity-sec test 72c: child_raise_privileges nodemap property ========================================================== 17:22:56 (1787865776) [ 5058.112901] Lustre: DEBUG MARKER: == sanity-sec test 72d: fileset inheritance for dynamic nodemap ========================================================== 17:23:44 (1787865824) [ 5121.405890] Lustre: DEBUG MARKER: == sanity-sec test 72e: dynamic nodemap reclassify ======= 17:24:46 (1787865886) [ 5162.350964] Lustre: DEBUG MARKER: == sanity-sec test 72f: fileset_modify on dynamic nodemap ========================================================== 17:25:27 (1787865927) [ 5224.515905] Lustre: DEBUG MARKER: == sanity-sec test 73: encrypted names in changelogs ===== 17:26:30 (1787865990) [ 5226.633823] Lustre: DEBUG MARKER: SKIP: sanity-sec test_73 Need fscrypt [ 5228.645598] Lustre: DEBUG MARKER: == sanity-sec test 74: Set nodemap deny_mount flag ======= 17:26:34 (1787865994) [ 5232.543231] Lustre: Unmounted lustre-client [ 5232.546079] Lustre: Skipped 6 previous similar messages [ 5251.205439] LustreError: 126147:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 9959us [ 5251.221107] LustreError: 126147:0:(obd_config.c:1432:process_param2_config()) Skipped 6 previous similar messages [ 5251.292153] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 5251.300265] Lustre: Skipped 6 previous similar messages [ 5258.741150] LustreError: 126281:0:(llite_lib.c:606:client_common_fill_super()) lustre-clilmv-ffff8cb244e58800: cannot mds_connect: rc = -1 [ 5258.836562] LustreError: 126281:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 5278.930733] Lustre: DEBUG MARKER: == sanity-sec test 75: check uid/gid/projid are set on OST and MDT for various RPCs ========================================================== 17:27:24 (1787866044) [ 5280.822525] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75 ldiskfs only test (using debugfs) [ 5282.831551] Lustre: DEBUG MARKER: == sanity-sec test 75a: test resource fs IDs against nodemap offset ========================================================== 17:27:28 (1787866048) [ 5286.497576] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75a need at least two clients [ 5288.594513] Lustre: DEBUG MARKER: == sanity-sec test 75b: test resource ID repair ========== 17:27:34 (1787866054) [ 5292.062509] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75b ldiskfs only test (using debugfs) [ 5294.427455] Lustre: DEBUG MARKER: == sanity-sec test 76: suppgroups and gid mapping ======== 17:27:39 (1787866059) [ 5337.399982] Lustre: DEBUG MARKER: == sanity-sec test 77: root offsetting =================== 17:28:23 (1787866103) [ 5384.652430] Lustre: DEBUG MARKER: == sanity-sec test 78: nodemap stats ===================== 17:29:10 (1787866150) [ 5424.600203] Lustre: DEBUG MARKER: == sanity-sec test 79: ssk for nodemap identification ==== 17:29:50 (1787866190) [ 5426.449859] Lustre: DEBUG MARKER: SKIP: sanity-sec test_79 Need shared key feature for this test [ 5428.758666] Lustre: DEBUG MARKER: == sanity-sec test 81a: nodemap ban list ================= 17:29:54 (1787866194) [ 5431.330799] Lustre: DEBUG MARKER: test_81a 20228 [ 5453.944814] Lustre: This client was banned by administrative request for file system lustre. All requests will get Operation not permitted. [ 5453.960491] LustreError: 132298:0:(file.c:6184:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5491.746839] LustreError: 132877:0:(file.c:6184:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5491.755925] LustreError: 132877:0:(file.c:6184:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5511.839518] LustreError: 133103:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.204.158@tcp: failed processing log, type 1: rc = -110 [ 5648.351906] LustreError: MGC192.168.204.158@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 5648.387048] LustreError: 133103:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 5661.407611] LustreError: 133345:0:(file.c:6184:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5661.414403] LustreError: 133345:0:(file.c:6184:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5667.489802] LustreError: 133382:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.204.158@tcp: failed processing log, type 1: rc = -110 [ 5803.999411] LustreError: MGC192.168.204.158@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 5804.032570] LustreError: 133382:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 5827.217365] Lustre: DEBUG MARKER: == sanity-sec test 81b: banned client does not block other ========================================================== 17:36:32 (1787866592) [ 5829.672926] Lustre: DEBUG MARKER: SKIP: sanity-sec test_81b Need 2 clients [ 5831.893320] Lustre: DEBUG MARKER: == sanity-sec test 82: export lock revoked after nodemap change ========================================================== 17:36:37 (1787866597) [ 5895.576685] Lustre: Unmounted lustre-client [ 5895.584090] Lustre: Skipped 11 previous similar messages [ 5902.652882] LustreError: 135947:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1804us [ 5902.667218] LustreError: 135947:0:(obd_config.c:1432:process_param2_config()) Skipped 9 previous similar messages [ 5902.727098] Lustre: Mounted lustre-client - version 2.17.57_120_gb73d7ca [ 5902.730951] Lustre: Skipped 8 previous similar messages [ 5904.599402] Lustre: DEBUG MARKER: == sanity-sec test 83: Suppgids for cross-MDT ops ======== 17:37:50 (1787866670) [ 5906.949945] Lustre: DEBUG MARKER: SKIP: sanity-sec test_83 needs >= 2 MDTs [ 5908.759575] Lustre: DEBUG MARKER: == sanity-sec test 84: do not squash trusted ids ========= 17:37:54 (1787866674) [ 5944.216051] Lustre: DEBUG MARKER: == sanity-sec test 85: forbid squashing to UID/GID 0 ===== 17:38:30 (1787866710) [ 5981.644524] Lustre: DEBUG MARKER: == sanity-sec test 93: incremental RBAC role modifications ========================================================== 17:39:07 (1787866747) [ 6054.457795] Lustre: DEBUG MARKER: == sanity-sec test 100: SSK automatic prime generation, binary/ASCII server keys ========================================================== 17:40:19 (1787866819) [ 6056.187303] Lustre: DEBUG MARKER: SKIP: sanity-sec test_100 Need shared key feature for this test [ 6058.248407] Lustre: DEBUG MARKER: == sanity-sec test 101: lgss_sk -a and -l support for ascii-encoded SSK keys ========================================================== 17:40:23 (1787866823) [ 6059.659402] Lustre: DEBUG MARKER: SKIP: sanity-sec test_101 Need shared key feature for this test [ 6061.769693] Lustre: DEBUG MARKER: == sanity-sec test 102: SSK automatic key loading from mount point ========================================================== 17:40:27 (1787866827) [ 6063.493396] Lustre: DEBUG MARKER: SKIP: sanity-sec test_102 Need shared key feature for this test [ 6065.554881] Lustre: DEBUG MARKER: == sanity-sec test 103: Multiple SSK keys on server side ========================================================== 17:40:31 (1787866831) [ 6066.973602] Lustre: DEBUG MARKER: SKIP: sanity-sec test_103 Need shared key feature for this test [ 6068.984605] Lustre: DEBUG MARKER: == sanity-sec test 104: SSK key removal from keyring ===== 17:40:34 (1787866834) [ 6070.655786] Lustre: DEBUG MARKER: SKIP: sanity-sec test_104 Need shared key feature for this test [ 6072.763917] Lustre: DEBUG MARKER: == sanity-sec test 105: update nodemap membership on flavor change ========================================================== 17:40:38 (1787866838) [ 6074.262768] Lustre: DEBUG MARKER: SKIP: sanity-sec test_105 Need shared key feature for this test [ 6075.954304] Lustre: DEBUG MARKER: == sanity-sec test 106: switch nodemap to gssonly ======== 17:40:42 (1787866842) [ 6077.719519] Lustre: DEBUG MARKER: SKIP: sanity-sec test_106 Need shared key feature for this test [ 6079.972323] Lustre: DEBUG MARKER: == sanity-sec test 200: sk_load_key broadens SSK key perms without @u linked ========================================================== 17:40:45 (1787866845) [ 6081.486919] Lustre: DEBUG MARKER: SKIP: sanity-sec test_200 Need shared key feature for this test [ 6083.737105] Lustre: DEBUG MARKER: == sanity-sec test 300: test user_principal mount option parsing ========================================================== 17:40:49 (1787866849) [ 6085.406769] Lustre: DEBUG MARKER: Mount with user_principal=mock_iam_test [ 6091.476832] Lustre: DEBUG MARKER: Mount with only user_principal (should fail) [ 6091.883780] LustreError: Unknown option 'user_principal', won't mount. [ 6091.891751] LustreError: 142830:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -22 [ 6093.177449] Lustre: DEBUG MARKER: Mount failed as expected with only -o user_principal [ 6099.731134] Lustre: DEBUG MARKER: cleanup: ====================================================== [ 6101.348784] Lustre: DEBUG MARKER: == sanity-sec test complete, duration 5830 sec =========== 17:41:07 (1787866867) [ 6103.141181] Lustre: DEBUG MARKER: === sanity-sec: start cleanup 17:41:09 (1787866869) === [ 6106.318716] Lustre: DEBUG MARKER: === sanity-sec: finish cleanup 17:41:12 (1787866872) === [ 6128.898399] Key type lgssc unregistered [ 6129.265244] LNet: 144603:0:(lib-ptl.c:964:lnet_clear_lazy_portal()) Active lazy portal 0 on exit [ 6129.277337] LNetError: 144603:0:(acceptor.c:252:lnet_acceptor_remove_socket()) Interface ens2 not found [ 6129.306292] LNet: Removed LNI 192.168.204.58@tcp [ 6130.109159] Key type .llcrypt unregistered [ 6130.110933] Key type ._llcrypt unregistered