[ 0.000000] Linux version 4.18.0rh8.10-debug (green@maintenance) (gcc version 8.5.0 20210514 (Red Hat 8.5.0-26) (GCC)) #2 SMP Mon Jul 14 01:24:22 EDT 2025 [ 0.000000] Command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.000000] signal: max sigframe size: 1776 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffd9fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bffda000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000146dfffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-10.fc44 06/10/2025 [ 0.000000] Hypervisor detected: KVM [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: using sched offset of 438071960 cycles [ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.000000] tsc: Detected 2399.998 MHz processor [ 0.000000] last_pfn = 0x146e00 max_arch_pfn = 0x400000000 [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] last_pfn = 0xbffda max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f54d0-0x000f54df] [ 0.000000] RAMDISK: [mem 0xbcc64000-0xbffcffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F52F0 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x00000000BFFE2464 000034 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x00000000BFFE2300 000074 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x00000000BFFE0040 0022C0 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACS 0x00000000BFFE0000 000040 [ 0.000000] ACPI: APIC 0x00000000BFFE2374 000090 (v03 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x00000000BFFE2404 000038 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: WAET 0x00000000BFFE243C 000028 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: Reserving FACP table memory at [mem 0xbffe2300-0xbffe2373] [ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xbffe0040-0xbffe22ff] [ 0.000000] ACPI: Reserving FACS table memory at [mem 0xbffe0000-0xbffe003f] [ 0.000000] ACPI: Reserving APIC table memory at [mem 0xbffe2374-0xbffe2403] [ 0.000000] ACPI: Reserving HPET table memory at [mem 0xbffe2404-0xbffe243b] [ 0.000000] ACPI: Reserving WAET table memory at [mem 0xbffe243c-0xbffe2463] [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000146dfffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x1465a3000-0x1465cdfff] [ 0.000000] Reserving 256MB of memory at 2752MB for crashkernel (System RAM: 4205MB) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000bffd9fff] [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Zeroed struct page in unavailable ranges: 4744 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000146dfffff] [ 0.000000] ACPI: PM-Timer IO Port: 0x608 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] TSC deadline timer available [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] kvm-guest: KVM setup pv remote TLB flush [ 0.000000] kvm-guest: setup PV sched yield [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbffda000-0xbfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfeffbfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeffc000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] [mem 0xc0000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.000000] kvm-guest: PV spinlocks enabled [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1059618 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] Specific versions of hardware are certified with Red Hat Enterprise Linux 8. Please see the list of hardware certified with Red Hat Enterprise Linux 8 at https://catalog.redhat.com. [ 0.000000] audit: disabled (until reboot) [ 0.000000] software IO TLB: area num 4. [ 0.000000] Memory: 2829700K/4306400K available (18435K kernel code, 11221K rwdata, 7248K rodata, 2908K init, 18040K bss, 524580K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] ftrace: allocating 41240 entries in 162 pages [ 0.000000] ftrace: allocated 162 pages with 3 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.000000] rcu: RCU callback double-/use-after-free debug enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x622/0x9a8 with crng_init=0 [ 0.001000] Console: colour *CGA 80x25 [ 0.001000] printk: console [ttyS1] enabled [ 0.001000] ACPI: Core revision 20220331 [ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.001009] APIC: Switch to symmetric I/O mode setup [ 0.002210] x2apic enabled [ 0.003005] Switched APIC routing to physical x2apic. [ 0.004011] kvm-guest: setup PV IPIs [ 0.006220] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.007000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 0.007018] Calibrating delay loop (skipped) preset value.. 4799.99 BogoMIPS (lpj=2399998) [ 0.008008] pid_max: default: 32768 minimum: 301 [ 0.009108] LSM: Security Framework initializing [ 0.010040] Yama: becoming mindful. [ 0.011030] SELinux: Initializing. [ 0.012062] *** VALIDATE selinux *** [ 0.020376] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc) [ 0.024462] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc) [ 0.025159] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.026082] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.027096] *** VALIDATE tmpfs *** [ 0.028478] *** VALIDATE proc *** [ 0.029262] *** VALIDATE cgroup *** [ 0.030010] *** VALIDATE cgroup2 *** [ 0.032218] x86/cpu: User Mode Instruction Prevention (UMIP) activated [ 0.033166] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.034008] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.035030] Spectre V2 : User space: Vulnerable [ 0.036009] Speculative Store Bypass: Vulnerable [ 0.039220] debug: unmapping init [mem 0xffffffff9a259000-0xffffffff9a260fff] [ 0.042168] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz (family: 0x6, model: 0x3e, stepping: 0x4) [ 0.043613] Performance Events: IvyBridge events, full-width counters, Intel PMU driver. [ 0.044030] ... version: 2 [ 0.045009] ... bit width: 48 [ 0.046009] ... generic registers: 4 [ 0.046979] ... value mask: 0000ffffffffffff [ 0.047017] ... max period: 00007fffffffffff [ 0.048010] ... fixed-purpose events: 3 [ 0.049007] ... event mask: 000000070000000f [ 0.050305] rcu: Hierarchical SRCU implementation. [ 0.052388] smp: Bringing up secondary CPUs ... [ 0.053566] x86: Booting SMP configuration: [ 0.054021] .... node #0, CPUs: #1 #2 #3 [ 0.059131] smp: Brought up 1 node, 4 CPUs [ 0.061024] smpboot: Max logical packages: 1 [ 0.062021] smpboot: Total of 4 processors activated (19199.98 BogoMIPS) [ 0.140749] node 0 deferred pages initialised in 76ms [ 0.143153] devtmpfs: initialized [ 0.144394] x86/mm: Memory block size: 128MB [ 0.148115] gcov: version magic: 0x41383552 [ 0.150560] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.151204] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc) [ 0.152398] pinctrl core: initialized pinctrl subsystem [ 0.153375] [ 0.154010] ************************************************************* [ 0.155030] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.156030] ** ** [ 0.157013] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.158014] ** ** [ 0.159015] ** This means that this kernel is built to expose internal ** [ 0.160012] ** IOMMU data structures, which may compromise security on ** [ 0.161014] ** your system. ** [ 0.162011] ** ** [ 0.163019] ** If you see this message and you are not debugging the ** [ 0.164016] ** kernel, report this immediately to your vendor! ** [ 0.165015] ** ** [ 0.166013] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.167011] ************************************************************* [ 0.168604] NET: Registered protocol family 16 [ 0.169459] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.170057] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.171062] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.172446] cpuidle: using governor menu [ 0.174558] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.176443] PCI: Using configuration type 1 for base access [ 0.178158] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on [ 0.186083] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.187027] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.188151] cryptd: max_cpu_qlen set to 1000 [ 0.189223] ACPI: Added _OSI(Module Device) [ 0.190015] ACPI: Added _OSI(Processor Device) [ 0.191012] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.192008] ACPI: Added _OSI(Processor Aggregator Device) [ 0.195161] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 0.198503] ACPI: Interpreter enabled [ 0.199039] ACPI: PM: (supports S0 S3 S4 S5) [ 0.200010] ACPI: Using IOAPIC for interrupt routing [ 0.201116] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.202373] ACPI: Enabled 2 GPEs in block 00 to 0F [ 0.209338] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.210028] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI HPX-Type3] [ 0.211017] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI] [ 0.212104] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.214025] acpiphp: Slot [2] registered [ 0.215108] acpiphp: Slot [5] registered [ 0.216141] acpiphp: Slot [6] registered [ 0.217130] acpiphp: Slot [3] registered [ 0.218117] acpiphp: Slot [4] registered [ 0.219102] acpiphp: Slot [7] registered [ 0.220128] acpiphp: Slot [8] registered [ 0.221112] acpiphp: Slot [9] registered [ 0.222068] acpiphp: Slot [10] registered [ 0.223091] acpiphp: Slot [11] registered [ 0.224097] acpiphp: Slot [12] registered [ 0.225090] acpiphp: Slot [13] registered [ 0.226098] acpiphp: Slot [14] registered [ 0.227101] acpiphp: Slot [15] registered [ 0.228130] acpiphp: Slot [16] registered [ 0.229097] acpiphp: Slot [17] registered [ 0.230105] acpiphp: Slot [18] registered [ 0.231088] acpiphp: Slot [19] registered [ 0.232089] acpiphp: Slot [20] registered [ 0.233105] acpiphp: Slot [21] registered [ 0.234129] acpiphp: Slot [22] registered [ 0.235112] acpiphp: Slot [23] registered [ 0.236107] acpiphp: Slot [24] registered [ 0.237106] acpiphp: Slot [25] registered [ 0.238095] acpiphp: Slot [26] registered [ 0.239108] acpiphp: Slot [27] registered [ 0.240110] acpiphp: Slot [28] registered [ 0.241131] acpiphp: Slot [29] registered [ 0.242100] acpiphp: Slot [30] registered [ 0.243094] acpiphp: Slot [31] registered [ 0.244061] PCI host bridge to bus 0000:00 [ 0.245021] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.246020] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.247022] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.248033] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.249022] pci_bus 0000:00: root bus resource [mem 0xe0000000000-0xe007fffffff window] [ 0.250026] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.251181] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.253028] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.255221] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.259776] pci 0000:00:01.1: reg 0x20: [io 0xc120-0xc12f] [ 0.262084] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.263022] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.264018] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.265021] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.266612] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.267789] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI [ 0.268073] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB [ 0.269865] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 [ 0.271790] pci 0000:00:02.0: reg 0x10: [io 0xc100-0xc11f] [ 0.276978] pci 0000:00:02.0: reg 0x20: [mem 0xe0000000000-0xe0000003fff 64bit pref] [ 0.278017] pci 0000:00:02.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref] [ 0.282056] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.285015] pci 0000:00:05.0: reg 0x10: [io 0xc000-0xc07f] [ 0.288018] pci 0000:00:05.0: reg 0x14: [mem 0xfebc0000-0xfebc0fff] [ 0.295017] pci 0000:00:05.0: reg 0x20: [mem 0xe0000004000-0xe0000007fff 64bit pref] [ 0.300560] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.322016] pci 0000:00:06.0: reg 0x10: [io 0xc080-0xc0ff] [ 0.329016] pci 0000:00:06.0: reg 0x14: [mem 0xfebc1000-0xfebc1fff] [ 0.344018] pci 0000:00:06.0: reg 0x20: [mem 0xe0000008000-0xe000000bfff 64bit pref] [ 0.356333] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.358247] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 0.359220] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 0.361339] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 0.363151] ACPI: PCI: Interrupt link LNKS configured for IRQ 9 [ 0.368032] iommu: Default domain type: Passthrough [ 0.369402] SCSI subsystem initialized [ 0.370190] ACPI: bus type USB registered [ 0.372139] usbcore: registered new interface driver usbfs [ 0.374119] usbcore: registered new interface driver hub [ 0.377128] usbcore: registered new device driver usb [ 0.379182] pps_core: LinuxPPS API ver. 1 registered [ 0.381013] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.385064] PTP clock support registered [ 0.387059] EDAC MC: Ver: 3.0.0 [ 0.389114] PCI: Using ACPI for IRQ routing [ 0.390585] NetLabel: Initializing [ 0.391009] NetLabel: domain hash size = 128 [ 0.392011] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.394069] NetLabel: unlabeled traffic allowed by default [ 0.395116] vgaarb: loaded [ 0.396354] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.398014] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.405011] clocksource: Switched to clocksource kvm-clock [ 0.500315] VFS: Disk quotas dquot_6.6.0 [ 0.501472] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.503062] *** VALIDATE ramfs *** [ 0.504057] *** VALIDATE hugetlbfs *** [ 0.505181] pnp: PnP ACPI init [ 0.507512] pnp: PnP ACPI: found 6 devices [ 0.522617] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.524685] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.525982] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.527259] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.528878] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.530341] pci_bus 0000:00: resource 8 [mem 0xe0000000000-0xe007fffffff window] [ 0.531953] NET: Registered protocol family 2 [ 0.533482] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc) [ 0.536587] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, vmalloc) [ 0.538732] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc) [ 0.542608] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc) [ 0.546397] TCP: Hash tables configured (established 65536 bind 65536) [ 0.548854] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, vmalloc) [ 0.552040] UDP hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.555213] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 0.558219] NET: Registered protocol family 1 [ 0.560279] RPC: Registered named UNIX socket transport module. [ 0.564449] RPC: Registered udp transport module. [ 0.566236] RPC: Registered tcp transport module. [ 0.567950] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.570307] NET: Registered protocol family 44 [ 0.571980] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.573993] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 0.576187] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.578404] PCI: CLS 0 bytes, default 64 [ 0.580183] Unpacking initramfs... [ 1.952727] debug: unmapping init [mem 0xffff9cfb7cc64000-0xffff9cfb7ffcffff] [ 1.956642] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.959131] software IO TLB: mapped [mem 0x00000000a8000000-0x00000000ac000000] (64MB) [ 1.962290] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 2.446732] Initialise system trusted keyrings [ 2.447725] Key type blacklist registered [ 2.448767] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 2.455191] zbud: loaded [ 2.457160] *** VALIDATE nfs *** [ 2.458174] *** VALIDATE nfs4 *** [ 2.459481] pstore: using deflate compression [ 2.463250] Platform Keyring initialized [ 2.578358] NET: Registered protocol family 38 [ 2.580201] Key type asymmetric registered [ 2.581376] Asymmetric key parser 'x509' registered [ 2.582531] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.585109] io scheduler mq-deadline registered [ 2.586527] io scheduler kyber registered [ 2.588194] io scheduler bfq registered [ 2.590139] atomic64_test: passed for x86-64 platform with CX8 and with SSE [ 2.592905] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.595536] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 2.598219] ACPI: Power Button [PWRF] [ 2.604221] ACPI: \_SB_.LNKB: Enabled at IRQ 10 [ 2.610382] ACPI: \_SB_.LNKA: Enabled at IRQ 11 [ 2.619223] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.646611] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.676443] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.684128] Non-volatile memory driver v1.3 [ 2.685271] Linux agpgart interface v0.103 [ 2.722917] virtio_blk virtio1: [vda] 146744 512-byte logical blocks (75.1 MB/71.7 MiB) [ 2.726105] vda: detected capacity change from 0 to 75132928 [ 2.743369] virtio_blk virtio2: [vdb] 2097152 512-byte logical blocks (1.07 GB/1.00 GiB) [ 2.746126] vdb: detected capacity change from 0 to 1073741824 [ 2.754424] libphy: Fixed MDIO Bus: probed [ 2.764854] usbcore: registered new interface driver usbserial_generic [ 2.767614] usbserial: USB Serial support registered for generic [ 2.770458] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 2.776211] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.778236] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.780930] mousedev: PS/2 mouse device common for all mice [ 2.783605] rtc_cmos 00:05: RTC can wake from S4 [ 2.786917] rtc_cmos 00:05: registered as rtc0 [ 2.789938] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 2.791279] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs [ 2.795746] intel_pstate: CPU model not supported [ 2.797869] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input4 [ 2.801056] hid: raw HID events driver (C) Jiri Kosina [ 2.805376] usbcore: registered new interface driver usbhid [ 2.806443] usbhid: USB HID core driver [ 2.806590] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input3 [ 2.807577] drop_monitor: Initializing network drop monitor service [ 2.810913] Initializing XFRM netlink socket [ 2.812143] NET: Registered protocol family 10 [ 2.813935] Segment Routing with IPv6 [ 2.814769] NET: Registered protocol family 17 [ 2.815793] mpls_gso: MPLS GSO support [ 2.819359] RAS: Correctable Errors collector initialized. [ 2.820533] AVX version of gcm_enc/dec engaged. [ 2.821496] AES CTR mode by8 optimization enabled [ 2.867943] sched_clock: Marking stable (2867867163, 0)->(3803860014, -935992851) [ 2.871638] registered taskstats version 1 [ 2.873613] Loading compiled-in X.509 certificates [ 2.875292] zswap: loaded using pool lzo/zbud [ 2.894132] Key type big_key registered [ 2.902665] Key type encrypted registered [ 2.903932] ima: No TPM chip found, activating TPM-bypass! [ 2.905768] ima: Allocated hash algorithm: sha1 [ 2.907414] ima: No architecture policies found [ 2.908969] evm: Initialising EVM extended attributes: [ 2.910882] evm: security.selinux [ 2.911779] evm: security.ima [ 2.912446] evm: security.capability [ 2.913251] evm: HMAC attrs: 0x1 [ 2.915825] rtc_cmos 00:05: setting system clock to 2026-09-08 03:42:18 UTC (1788838938) [ 2.921098] debug: unmapping init [mem 0xffffffff9b203000-0xffffffff9b3fffff] [ 2.923334] debug: unmapping init [mem 0xffffffff99f82000-0xffffffff9a258fff] [ 2.931087] Write protecting the kernel read-only data: 28672k [ 2.933589] debug: unmapping init [mem 0xffffffff98603000-0xffffffff987fffff] [ 2.935418] debug: unmapping init [mem 0xffffffff98f14000-0xffffffff98ffffff] [ 2.957674] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 2.962860] systemd[1]: Detected virtualization kvm. [ 2.964239] systemd[1]: Detected architecture x86-64. [ 2.965359] systemd[1]: Running in initial RAM disk. Welcome to Rocky Linux 8.10 (Green Obsidian) dracut-049-233.git20240115.el8 (Initramfs)! [ 2.990603] systemd[1]: No hostname configured. [ 2.992304] systemd[1]: Set hostname to . [ 2.994237] random: systemd: uninitialized urandom read (16 bytes read) [ 2.995784] systemd[1]: Initializing machine ID from random generator. [ 3.046265] random: ln: uninitialized urandom read (6 bytes read) [ 3.105602] random: systemd: uninitialized urandom read (16 bytes read) [ 3.106935] systemd[1]: Reached target Initrd Root Device. [ OK ] Reached target Initrd Root Device. [ 3.111314] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 3.118306] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Reached target Local File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket. Starting Create Volatile Files and Directories... [ OK ] Started Memstrack Anylazing Service. Starting Journal Service... Starting Apply Kernel Variables... Starting Create list of required st…ce nodes for the current kernel... [ OK ] Listening on udev Control Socket. [ OK ] Reached target Timers. Starting Setup Virtual Console... [ OK ] Reached target Sockets. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Setup Virtual Console. Starting dracut cmdline hook... Starting Create Static Device Nodes in /dev... [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started dracut cmdline hook. Starting dracut pre-udev hook... [ 3.668148] device-mapper: uevent: version 1.0.3 [ 3.670425] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ OK ] Started dracut pre-udev hook. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook. Starting udev Coldplug all Devices... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started udev Coldplug all Devices. Starting dracut initqueue hook... [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 4.459568] virtio_net virtio0 ens2: renamed from eth0 [ 4.504904] scsi host0: ata_piix [ 4.539518] scsi host1: ata_piix [ 4.541291] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc120 irq 14 [ 4.543731] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc128 irq 15 [ 8.301129] dracut-initqueue[583]: RTNETLINK answers: File exists [ 9.418631] random: crng init done [ 9.420177] random: 7 urandom warning(s) missed due to ratelimiting Starting nbd nbd0... [ OK ] Started nbd nbd0. [ OK ] Started dracut initqueue hook. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting /sysroot... [ 9.844056] EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /sysroot. [ OK ] Reached target Initrd Root File System. Starting Reload Configuration from the Real Root... [ OK ] Started Reload Configuration from the Real Root. [ OK ] Reached target Initrd File Systems. [ OK ] Reached target Initrd Default Target. Starting dracut pre-pivot and cleanup hook... [ OK ] Started dracut pre-pivot and cleanup hook. Starting Cleaning Up and Shutting Down Daemons... [ OK ] Stopped target Timers. Stopping Hardware RNG Entropy Gatherer Daemon... [ OK ] Stopped dracut pre-pivot and cleanup hook. [ OK ] Stopped target Initrd Default Target. [ OK ] Stopped target Initrd Root Device. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped dracut initqueue hook. [ OK ] Stopped Hardware RNG Entropy Gatherer Daemon. [ OK ] Stopped target Basic System. [ OK ] Stopped target Slices. [ OK ] Stopped target Paths. [ OK ] Stopped target Sockets. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Swap. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped udev Coldplug all Devices. [ OK ] Stopped dracut pre-trigger hook. Stopping udev Kernel Device Manager... [ OK ] Stopped target Local File Systems. [ OK ] Stopped Apply Kernel Variables. [ OK ] Started Cleaning Up and Shutting Down Daemons. [ OK ] Stopped udev Kernel Device Manager. [ OK ] Stopped dracut pre-udev hook. [ OK ] Stopped dracut cmdline hook. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create list of required sta…vice nodes for the current kernel. [ OK ] Closed udev Kernel Socket. [ OK ] Closed udev Control Socket. Starting Cleanup udevd DB... [ OK ] Started Cleanup udevd DB. [ OK ] Reached target Switch Root. Starting Switch Root... [ 11.000840] printk: systemd: 25 output lines suppressed due to ratelimiting [ 11.285356] SELinux: Disabled at runtime. [ 11.343750] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 11.352144] systemd[1]: Detected virtualization kvm. [ 11.354589] systemd[1]: Detected architecture x86-64. Welcome to Rocky Linux 8.10 (Green Obsidian)! [ 11.867906] systemd[1]: initrd-switch-root.service: Succeeded. [ 11.873525] systemd[1]: Stopped Switch Root. [ OK ] Stopped Switch Root. [ 11.878552] systemd[1]: systemd-journald.service: Service has no hold-off time (RestartSec=0), scheduling restart. [ 11.882745] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1. [ 11.885928] systemd[1]: Stopped Journal Service. [ OK ] Stopped Journal Service. [ 11.897931] systemd[1]: Starting Journal Service... Starting Journal Service... [ 11.903348] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Created slice User and Session Slice. [ OK ] Reached target rpc_pipefs.target. [ OK ] Created slice system-getty.slice. [ OK ] Listening on initctl Compatibility Named Pipe. Starting Remount Root and Kernel File Systems... [FAILED] Failed to set up automount Arbitrar…rmats File System Automount Point. See 'systemctl status proc-sys-fs-binfmt_misc.automount' for details. Mounting Kernel Debug File System... [ OK ] Created slice system-sshd\x2dkeygen.slice. Starting Apply Kernel Variables... Mounting Huge Pages File System... [ OK ] Listening on Process Core Dump Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Starting udev Coldplug all Devices... Activating swap /dev/disk/by-label/SWAP... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... [ OK ] Stopped target Switch Root. [ OK ] Stopped target Initrd File Systems. [ OK ] Stopped target Initrd Root File System. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Slices. [ OK ] Reached target RPC Port Mapper. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 12.073382] Adding 1048572k swap on /dev/vdb. Priority:-2 extents:1 across:1048572k FS [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Started Journal Service. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Huge Pages File System. [ OK ] Activated swap /dev/disk/by-label/SWAP. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Reached target Swap. Starting Configure read-only root support... Starting Create Static Device Nodes in /dev... Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /mnt... Mounting /home/green/git/lustre-release... [ OK ] Started udev Coldplug all Devices. [ OK ] Mounted /mnt. [ 12.663815] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ OK ] Mounted /home/green/git/lustre-release. [ OK ] Started udev Kernel Device Manager. [ 13.253964] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0 [ 13.306571] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 13.654145] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer [ 13.707785] EDAC sbridge: Ver: 1.1.2 [ 17.014595] Key type dns_resolver registered [ 17.825426] NFS: Registering the id_resolver key type [ 17.828766] Key type id_resolver registered [ 17.832137] Key type id_legacy registered [* ] A start job is running for Configur…-only root support (6s / no limit) [ OK ] Started Configure read-only root support. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Mark the need to relabel after reboot... Starting Rebuild Dynamic Linker Cache... Starting Create Volatile Files and Directories... [ OK ] Started Load/Save Random Seed. [ OK ] Started Mark the need to relabel after reboot. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting RPC Bind... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC Bind. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started irqbalance daemon. Starting Login Service... [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started D-Bus System Message Bus. Starting Network Manager... [ OK ] Started dnf makecache --timer. [ OK ] Reached target sshd-keygen.target. Starting Restore /run/initramfs on shutdown... [ OK ] Started daily update of the root trust anchor for DNSSEC. [ OK ] Reached target Timers. [ OK ] Started Restore /run/initramfs on shutdown. [ OK ] Started Login Service. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting OpenSSH server daemon... Starting Dynamic System Tuning Daemon... Starting GSSAPI Proxy Daemon... Starting Network Manager Wait Online... Starting Hostname Service... [ OK ] Started OpenSSH server daemon. [ OK ] Started GSSAPI Proxy Daemon. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Started Command Scheduler. [ OK ] Started Serial Getty on ttyS1. [ OK ] Reached target Login Prompts. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting Crash recovery kernel arming... Starting Notify NFS peers of a restart... Starting System Logging Service... [ OK ] Started Notify NFS peers of a restart. [ OK ] Started System Logging Service. Rocky Linux 8.10 (Green Obsidian) Kernel 4.18.0rh8.10-debug on an x86_64 oleg234-client login: [ 44.007842] hrtimer: interrupt took 9834516 ns [ 77.816319] libcfs: loading out-of-tree module taints kernel. [ 77.918891] Key type ._llcrypt registered [ 77.921111] Key type .llcrypt registered [ 78.788219] libcfs: HW NUMA nodes: 1, HW CPU cores: 4, npartitions: 2 [ 78.840978] alg: No test for adler32 (adler32-zlib) [ 80.186760] Lustre: Lustre: Build Version: 2.17.57_115_g0321d60 [ 80.965123] LNet: Added LNI 192.168.202.34@tcp [8/256/0/180] [ 82.695213] Key type lgssc registered [ 84.523865] Lustre: Echo OBD driver; http://www.lustre.org/ [ 203.168193] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 208.009658] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 222.511564] Lustre: DEBUG MARKER: oleg234-client.virtnet: executing check_logdir /tmp/testlogs/ [ 228.176521] Lustre: DEBUG MARKER: oleg234-client.virtnet: executing yml_node [ 228.835585] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 23s idle [ 232.527682] Lustre: DEBUG MARKER: Client: 2.17.57.115 [ 234.906141] Lustre: DEBUG MARKER: MDS: 2.17.57.115 [ 237.655683] Lustre: DEBUG MARKER: OSS: 2.17.57.115 [ 239.212927] Lustre: DEBUG MARKER: -----============= acceptance-small: sanity-sec ============----- Mon Sep 7 23:46:13 EDT 2026 [ 256.879271] Lustre: DEBUG MARKER: excepting tests: 27 [ 258.359919] Lustre: DEBUG MARKER: skipping tests SLOW=no: 26 [ 261.067516] Lustre: DEBUG MARKER: === sanity-sec: start setup 23:46:34 (1788839194) === [ 267.127805] Lustre: DEBUG MARKER: oleg234-client.virtnet: executing check_config_client /mnt/lustre [ 286.948692] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 301.632839] Lustre: DEBUG MARKER: === sanity-sec: finish setup 23:47:15 (1788839235) === [ 307.209610] Lustre: DEBUG MARKER: == sanity-sec test 0: uid permission ======================================================================================= 23:47:21 (1788839241) [ 315.816453] Lustre: DEBUG MARKER: == sanity-sec test 1: setuid/gid ======================================================================================= 23:47:29 (1788839249) [ 317.563700] Lustre: DEBUG MARKER: SKIP: sanity-sec test_1 without GSS support. [ 319.707992] Lustre: DEBUG MARKER: == sanity-sec test 4: set supplementary group ========================================================================= 23:47:33 (1788839253) [ 331.231146] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 22s idle [ 331.240602] Lustre: Skipped 1 previous similar message [ 331.471714] Lustre: DEBUG MARKER: == sanity-sec test 5: Test l_getidentity with a nonexistent user on the MDT ========================================================== 23:47:45 (1788839265) [ 358.536468] Lustre: DEBUG MARKER: == sanity-sec test 7: nodemap create and delete ========== 23:48:12 (1788839292) [ 396.830062] Lustre: DEBUG MARKER: == sanity-sec test 8: nodemap reject duplicates ========== 23:48:50 (1788839330) [ 445.663690] Lustre: DEBUG MARKER: == sanity-sec test 9: nodemap range add ================== 23:49:39 (1788839379) [ 493.085443] Lustre: DEBUG MARKER: == sanity-sec test 10a: nodemap reject duplicate ranges == 23:50:27 (1788839427) [ 542.917116] Lustre: DEBUG MARKER: == sanity-sec test 10b: delete range from the correct nodemap ========================================================== 23:51:16 (1788839476) [ 558.248836] Lustre: DEBUG MARKER: == sanity-sec test 10c: verfify contiguous range support ========================================================== 23:51:32 (1788839492) [ 570.866447] Lustre: DEBUG MARKER: == sanity-sec test 10d: verfify nodemap range format '*@' support ========================================================== 23:51:45 (1788839505) [ 582.307300] Lustre: DEBUG MARKER: == sanity-sec test 11: nodemap modify ==================== 23:51:56 (1788839516) [ 626.224743] Lustre: DEBUG MARKER: == sanity-sec test 12: nodemap set squash ids ============ 23:52:40 (1788839560) [ 670.344414] Lustre: DEBUG MARKER: == sanity-sec test 13: test nids ========================= 23:53:24 (1788839604) [ 716.588460] Lustre: DEBUG MARKER: == sanity-sec test 14: test default nodemap nid lookup === 23:54:11 (1788839651) [ 758.080436] Lustre: DEBUG MARKER: == sanity-sec test 15: test id mapping =================== 23:54:52 (1788839692) [ 909.501261] Lustre: DEBUG MARKER: == sanity-sec test 16: test nodemap all_off fileops ====== 23:57:23 (1788839843) [ 981.472072] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 20s idle [ 981.479386] Lustre: Skipped 1 previous similar message [ 1048.031260] Lustre: lustre-OST0001-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 1142.797236] Lustre: DEBUG MARKER: == sanity-sec test 17: test nodemap trusted_noadmin fileops ========================================================== 00:01:17 (1788840077) [ 1150.432551] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 23s idle [ 1247.719897] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 1247.730308] Lustre: Skipped 1 previous similar message [ 1298.911266] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 1360.353089] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 22s idle [ 1411.552178] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 1478.111514] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 23s idle [ 1478.121778] Lustre: Skipped 1 previous similar message [ 1590.767963] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 23s idle [ 1590.777940] Lustre: Skipped 1 previous similar message [ 1641.254479] Lustre: DEBUG MARKER: == sanity-sec test 18: test nodemap mapped_noadmin fileops ========================================================== 00:09:34 (1788840574) [ 1749.471259] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 1749.478593] Lustre: Skipped 2 previous similar messages [ 1911.397923] Lustre: DEBUG MARKER: == sanity-sec test 19: test nodemap trusted_admin fileops ========================================================== 00:14:05 (1788840845) [ 2085.791111] Lustre: DEBUG MARKER: == sanity-sec test 20: test nodemap mapped_admin fileops ========================================================== 00:17:00 (1788841020) [ 2092.516752] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 24s idle [ 2092.523337] Lustre: Skipped 5 previous similar messages [ 2255.066804] Lustre: DEBUG MARKER: == sanity-sec test 21: test nodemap mapped_trusted_noadmin fileops ========================================================== 00:19:49 (1788841189) [ 2517.415466] Lustre: DEBUG MARKER: == sanity-sec test 22: test nodemap mapped_trusted_admin fileops ========================================================== 00:24:11 (1788841451) [ 2691.516656] Lustre: DEBUG MARKER: == sanity-sec test 23a: test mapped regular ACLs ========= 00:27:05 (1788841625) [ 2692.993859] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23a Need 2 clients at least [ 2694.633444] Lustre: DEBUG MARKER: == sanity-sec test 23b: test mapped default ACLs ========= 00:27:08 (1788841628) [ 2696.071438] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23b Need 2 clients at least [ 2696.671215] Lustre: lustre-OST0000-osc-ffff9cfbc52a4000: disconnect after 23s idle [ 2696.687322] Lustre: Skipped 9 previous similar messages [ 2697.951580] Lustre: DEBUG MARKER: == sanity-sec test 24: check nodemap proc files for LBUGs and Oopses ========================================================== 00:27:12 (1788841632) [ 2731.381155] Lustre: DEBUG MARKER: == sanity-sec test 25a: test save and reload nodemap config ========================================================== 00:27:45 (1788841665) [ 2735.440514] Lustre: Unmounted lustre-client [ 2771.982439] Lustre: DEBUG MARKER: === sanity-sec: start setup 00:28:24 (1788841704) === [ 2813.426128] LustreError: 64344:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 3980us [ 2813.491394] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 2818.833356] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 2827.025942] Lustre: DEBUG MARKER: === sanity-sec: finish setup 00:29:21 (1788841761) === [ 2829.112903] Lustre: Unmounted lustre-client [ 2842.050385] LustreError: 65422:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1508us [ 2842.110114] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 2848.520593] Lustre: DEBUG MARKER: == sanity-sec test 25b: test nodemap info values ========= 00:29:42 (1788841782) [ 2891.826499] Lustre: DEBUG MARKER: == sanity-sec test 25c: test yaml-compliance for nodemap ========================================================== 00:30:25 (1788841825) [ 2914.234282] Lustre: Unmounted lustre-client [ 2914.560897] LustreError: 67701:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1941us [ 2914.579798] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 2923.318229] Lustre: Unmounted lustre-client [ 2932.802334] LustreError: 68378:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 7171us [ 2932.859897] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 2934.661566] Lustre: DEBUG MARKER: SKIP: sanity-sec test_26 skipping SLOW test 26 [ 2936.487251] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27a skipping excluded test 27a (base 27) [ 2938.496838] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27aa skipping excluded test 27aa (base 27) [ 2940.264371] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ab skipping excluded test 27ab (base 27) [ 2942.373621] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ac skipping excluded test 27ac (base 27) [ 2943.880539] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ad skipping excluded test 27ad (base 27) [ 2945.646948] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27b skipping excluded test 27b (base 27) [ 2947.520555] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27c skipping excluded test 27c (base 27) [ 2949.457510] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27d skipping excluded test 27d (base 27) [ 2951.453500] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27e skipping excluded test 27e (base 27) [ 2953.337393] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27f skipping excluded test 27f (base 27) [ 2955.452579] Lustre: DEBUG MARKER: == sanity-sec test 28: check shared key rotation method == 00:31:29 (1788841889) [ 2956.928795] Lustre: DEBUG MARKER: SKIP: sanity-sec test_28 need shared key feature for this test [ 2958.889980] Lustre: DEBUG MARKER: == sanity-sec test 29: check for missing shared key ====== 00:31:32 (1788841892) [ 2960.422816] Lustre: DEBUG MARKER: SKIP: sanity-sec test_29 need shared key feature for this test [ 2962.585625] Lustre: DEBUG MARKER: == sanity-sec test 30: check for invalid shared key ====== 00:31:36 (1788841896) [ 2964.217828] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30 need shared key feature for this test [ 2966.148725] Lustre: DEBUG MARKER: == sanity-sec test 30b: basic test of all different SSK flavors ========================================================== 00:31:40 (1788841900) [ 2968.085439] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30b need shared key feature for this test [ 2970.207641] Lustre: DEBUG MARKER: == sanity-sec test 31: client mount option '-o network' == 00:31:44 (1788841904) [ 2973.708133] Lustre: DEBUG MARKER: SKIP: sanity-sec test_31 without lnetctl support. [ 2975.322602] Lustre: DEBUG MARKER: == sanity-sec test 32: check for mgssec ================== 00:31:49 (1788841909) [ 2979.184715] Lustre: DEBUG MARKER: SKIP: sanity-sec test_32 need shared key feature for this test [ 2981.444801] Lustre: DEBUG MARKER: == sanity-sec test 33: correct srpc flags for MGS connection ========================================================== 00:31:55 (1788841915) [ 2983.268893] Lustre: DEBUG MARKER: SKIP: sanity-sec test_33 need shared key feature for this test [ 2985.064417] Lustre: DEBUG MARKER: == sanity-sec test 34: deny_unknown on default nodemap === 00:31:59 (1788841919) [ 3009.815144] Lustre: DEBUG MARKER: == sanity-sec test 35: Check permissions when accessing changelogs ========================================================== 00:32:23 (1788841943) [ 3037.242873] LustreError: 73583:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9cfbc88e2000: fail to open changelog catalog: rc = -13 [ 3049.637827] Lustre: DEBUG MARKER: == sanity-sec test 36: control if clients can use encryption ========================================================== 00:33:04 (1788841984) [ 3051.645797] Lustre: Unmounted lustre-client [ 3052.015061] LustreError: 74000:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2011us [ 3052.051109] Lustre: Test dummy encryption mode enabled [ 3052.059649] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3052.313550] llcrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-aesni)" [ 3059.092994] Lustre: Test dummy encryption mode enabled [ 3061.588616] Lustre: Unmounted lustre-client [ 3061.593161] Lustre: Skipped 1 previous similar message [ 3065.562227] LustreError: 74312:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 4387us [ 3065.576696] LustreError: 74312:0:(obd_config.c:1432:process_param2_config()) Skipped 1 previous similar message [ 3065.596712] Lustre: lustre-MDT0000-mdc-ffff9cfbc5fe2800: connection denied by lustre-MDT0000_UUID: rc = -13 [ 3065.602875] LustreError: 74288:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9cfbc5fe2800: can't stat MDS #0: rc = -13 [ 3065.646614] LustreError: 74288:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -13 [ 3085.509843] LustreError: 75016:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1241us [ 3085.581233] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3085.583842] Lustre: Skipped 1 previous similar message [ 3088.308614] Lustre: Unmounted lustre-client [ 3088.317641] Lustre: Skipped 1 previous similar message [ 3090.007933] bash (73793): drop_caches: 3 [ 3092.791961] Lustre: DEBUG MARKER: == sanity-sec test 37: simple encrypted file ============= 00:33:46 (1788842026) [ 3094.464746] Lustre: DEBUG MARKER: SKIP: sanity-sec test_37 ldiskfs only test (using debugfs) [ 3096.198615] Lustre: DEBUG MARKER: == sanity-sec test 38: encrypted file with hole ========== 00:33:50 (1788842030) [ 3097.465613] Lustre: DEBUG MARKER: SKIP: sanity-sec test_38 skip ZFS backend [ 3099.271636] Lustre: DEBUG MARKER: == sanity-sec test 39: rewrite data in already encrypted page ========================================================== 00:33:53 (1788842033) [ 3101.454799] Lustre: Test dummy encryption mode enabled [ 3102.006906] llcrypt: AES-256-XTS using implementation "xts-aes-aesni" [ 3110.275595] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3110.279861] Lustre: Skipped 2 previous similar messages [ 3110.806800] bash (75721): drop_caches: 3 [ 3113.610614] Lustre: DEBUG MARKER: == sanity-sec test 40: exercise size of encrypted file === 00:34:06 (1788842046) [ 3116.531130] Lustre: Test dummy encryption mode enabled [ 3123.039477] Lustre: Unmounted lustre-client [ 3123.042600] Lustre: Skipped 3 previous similar messages [ 3123.358189] LustreError: 76889:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 1781us [ 3123.375503] LustreError: 76889:0:(obd_config.c:1432:process_param2_config()) Skipped 4 previous similar messages [ 3123.938363] bash (76492): drop_caches: 3 [ 3133.476628] bash (76492): drop_caches: 3 [ 3136.388623] Lustre: DEBUG MARKER: == sanity-sec test 41: test race on encrypted file size (1) ========================================================== 00:34:29 (1788842069) [ 3139.809918] Lustre: Test dummy encryption mode enabled [ 3166.093143] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3166.096636] Lustre: Skipped 4 previous similar messages [ 3166.693295] bash (77448): drop_caches: 3 [ 3169.509876] Lustre: DEBUG MARKER: == sanity-sec test 42: test race on encrypted file size (2) ========================================================== 00:35:02 (1788842102) [ 3172.475350] Lustre: Test dummy encryption mode enabled [ 3199.343153] Lustre: Unmounted lustre-client [ 3199.348718] Lustre: Skipped 4 previous similar messages [ 3199.710901] LustreError: 79014:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 6337us [ 3199.732975] LustreError: 79014:0:(obd_config.c:1432:process_param2_config()) Skipped 5 previous similar messages [ 3203.251503] bash (78239): drop_caches: 3 [ 3206.537251] Lustre: DEBUG MARKER: == sanity-sec test 43: test race on encrypted file size (3) ========================================================== 00:35:39 (1788842139) [ 3208.480838] Lustre: Test dummy encryption mode enabled [ 3208.482657] Lustre: Skipped 1 previous similar message [ 3236.427144] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3236.438593] Lustre: Skipped 5 previous similar messages [ 3240.195956] bash (79080): drop_caches: 3 [ 3243.500882] Lustre: DEBUG MARKER: == sanity-sec test 44: encrypted file access semantics: direct IO ========================================================== 00:36:16 (1788842176) [ 3245.470600] Lustre: DEBUG MARKER: SKIP: sanity-sec test_44 This test needs vmtouch utility [ 3247.351362] Lustre: DEBUG MARKER: == sanity-sec test 45: encrypted file access semantics: MMAP ========================================================== 00:36:21 (1788842181) [ 3250.016650] Lustre: Test dummy encryption mode enabled [ 3250.024780] Lustre: Skipped 1 previous similar message [ 3260.332829] bash (80219): drop_caches: 3 [ 3263.380747] Lustre: DEBUG MARKER: == sanity-sec test 46: encrypted file access semantics without key ========================================================== 00:36:36 (1788842196) [ 3266.773100] bash (80989): drop_caches: 3 [ 3270.460922] bash (80989): drop_caches: 3 [ 3271.392451] LustreError: 81343:0:(llite_lib.c:4132:ll_prep_md_op_data()) lustre: failed to setup filename: rc = -126 [ 3281.741281] bash (80989): drop_caches: 3 [ 3284.731922] Lustre: DEBUG MARKER: == sanity-sec test 47: encrypted file access semantics: rename/link ========================================================== 00:36:57 (1788842217) [ 3296.337421] bash (81867): drop_caches: 3 [ 3322.950751] bash (81867): drop_caches: 3 [ 3334.185031] Lustre: Unmounted lustre-client [ 3334.191219] Lustre: Skipped 11 previous similar messages [ 3335.326592] LustreError: 82940:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 14294us [ 3335.367732] LustreError: 82940:0:(obd_config.c:1432:process_param2_config()) Skipped 10 previous similar messages [ 3336.271837] bash (81867): drop_caches: 3 [ 3339.907532] Lustre: DEBUG MARKER: == sanity-sec test 48a: encrypted file access semantics: truncate ========================================================== 00:37:52 (1788842272) [ 3344.101745] Lustre: Test dummy encryption mode enabled [ 3344.105414] Lustre: Skipped 2 previous similar messages [ 3347.051756] bash (82983): drop_caches: 3 [ 3351.462756] bash (82983): drop_caches: 3 [ 3362.838873] bash (82983): drop_caches: 3 [ 3365.599446] Lustre: DEBUG MARKER: == sanity-sec test 48b: encrypted file: concurrent truncate ========================================================== 00:38:18 (1788842298) [ 3367.256628] Lustre: DEBUG MARKER: SKIP: sanity-sec test_48b Need at least 2 clients [ 3369.171489] Lustre: DEBUG MARKER: == sanity-sec test 49: Avoid getxattr for encryption context ========================================================== 00:38:23 (1788842303) [ 3372.421262] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3372.423985] Lustre: Skipped 11 previous similar messages [ 3373.395831] bash (84214): drop_caches: 3 [ 3374.390060] bash (84214): drop_caches: 3 [ 3376.120224] bash (84214): drop_caches: 3 [ 3377.329535] bash (84214): drop_caches: 3 [ 3380.854930] Lustre: DEBUG MARKER: SKIP: sanity-sec test_49 2nd part needs >= 2 MDTs [ 3388.397246] bash (84214): drop_caches: 3 [ 3391.524452] Lustre: DEBUG MARKER: == sanity-sec test 50: DoM encrypted file ================ 00:38:44 (1788842324) [ 3395.540351] bash (85227): drop_caches: 3 [ 3396.121173] bash (85227): drop_caches: 3 [ 3396.835363] Lustre: 85484:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3397.114283] bash (85227): drop_caches: 3 [ 3398.084212] bash (85227): drop_caches: 3 [ 3398.846785] Lustre: 85509:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3399.157432] bash (85227): drop_caches: 3 [ 3399.648611] bash (85227): drop_caches: 3 [ 3400.200050] Lustre: 85534:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3400.621722] bash (85227): drop_caches: 3 [ 3401.271603] bash (85227): drop_caches: 3 [ 3402.297481] bash (85227): drop_caches: 3 [ 3402.813616] bash (85227): drop_caches: 3 [ 3403.508882] Lustre: 85585:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x2:0x0] with data: rc = -126 [ 3403.523889] Lustre: 85585:0:(file.c:676:ll_dom_finish_open()) Skipped 1 previous similar message [ 3403.912347] bash (85227): drop_caches: 3 [ 3404.277259] bash (85227): drop_caches: 3 [ 3405.274666] bash (85227): drop_caches: 3 [ 3406.005681] bash (85227): drop_caches: 3 [ 3407.066750] bash (85227): drop_caches: 3 [ 3407.851666] bash (85227): drop_caches: 3 [ 3409.191570] bash (85227): drop_caches: 3 [ 3409.667140] bash (85227): drop_caches: 3 [ 3410.397872] bash (85227): drop_caches: 3 [ 3410.995924] bash (85227): drop_caches: 3 [ 3412.026262] bash (85227): drop_caches: 3 [ 3412.713427] bash (85227): drop_caches: 3 [ 3413.350248] Lustre: 85737:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000410:0x3:0x0] with data: rc = -126 [ 3413.364158] Lustre: 85737:0:(file.c:676:ll_dom_finish_open()) Skipped 2 previous similar messages [ 3413.753514] bash (85227): drop_caches: 3 [ 3414.391117] bash (85227): drop_caches: 3 [ 3415.381297] bash (85227): drop_caches: 3 [ 3416.035295] bash (85227): drop_caches: 3 [ 3426.723448] bash (85227): drop_caches: 3 [ 3429.890527] Lustre: DEBUG MARKER: == sanity-sec test 51: FS capabilities =================== 00:39:22 (1788842362) [ 3482.097287] Lustre: DEBUG MARKER: == sanity-sec test 52: Mirrored encrypted file =========== 00:40:16 (1788842416) [ 3486.635284] Lustre: Test dummy encryption mode enabled [ 3486.645194] Lustre: Skipped 2 previous similar messages [ 3490.191593] LustreError: 87928:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9cfbc4d1c800: inode [0x200000412:0x4:0x0] mdc close failed: rc = -22 [ 3498.064937] bash (87643): drop_caches: 3 [ 3500.392816] Lustre: DEBUG MARKER: == sanity-sec test 53: Mixed PAGE_SIZE clients =========== 00:40:34 (1788842434) [ 3501.807533] Lustre: DEBUG MARKER: SKIP: sanity-sec test_53 Need 64K PAGE_SIZE client [ 3503.304420] Lustre: DEBUG MARKER: == sanity-sec test 54: Encryption policies with fscrypt == 00:40:37 (1788842437) [ 3504.941271] Lustre: DEBUG MARKER: SKIP: sanity-sec test_54 This test needs fscrypt userspace tool [ 3506.542585] Lustre: DEBUG MARKER: == sanity-sec test 55: access with seteuid =============== 00:40:40 (1788842440) [ 3537.308702] Lustre: DEBUG MARKER: == sanity-sec test 56: FIEMAP on encrypted file ========== 00:41:11 (1788842471) [ 3538.356855] Lustre: DEBUG MARKER: SKIP: sanity-sec test_56 skip ZFS backend [ 3540.214227] Lustre: DEBUG MARKER: == sanity-sec test 57: security.c/encryption.c xattr protection ========================================================== 00:41:14 (1788842474) [ 3541.614827] Lustre: DEBUG MARKER: SKIP: sanity-sec test_57 skip ZFS backend [ 3543.158475] Lustre: DEBUG MARKER: == sanity-sec test 58: access to enc file's xattrs ======= 00:41:17 (1788842477) [ 3544.522870] Lustre: DEBUG MARKER: SKIP: sanity-sec test_58 skip ZFS backend [ 3546.381913] Lustre: DEBUG MARKER: == sanity-sec test 59a: mirror resync of encrypted files without key ========================================================== 00:41:20 (1788842480) [ 3552.779358] bash (91044): drop_caches: 3 [ 3554.281715] bash (91044): drop_caches: 3 [ 3567.137409] bash (91044): drop_caches: 3 [ 3570.136303] Lustre: DEBUG MARKER: == sanity-sec test 59b: migrate/extend/split of encrypted files without key ========================================================== 00:41:43 (1788842503) [ 3576.748650] bash (92000): drop_caches: 3 [ 3578.225683] bash (92000): drop_caches: 3 [ 3584.360852] bash (92000): drop_caches: 3 [ 3585.747661] bash (92000): drop_caches: 3 [ 3592.299966] Lustre: Unmounted lustre-client [ 3592.303624] Lustre: Skipped 20 previous similar messages [ 3592.826201] LustreError: 92705:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2322us [ 3592.848613] LustreError: 92705:0:(obd_config.c:1432:process_param2_config()) Skipped 20 previous similar messages [ 3593.414929] bash (92000): drop_caches: 3 [ 3593.896913] LustreError: 92742:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9cfbc69ce000: inode [0x200000416:0x2:0x0] mdc close failed: rc = -22 [ 3594.545106] bash (92000): drop_caches: 3 [ 3607.658502] bash (92000): drop_caches: 3 [ 3610.809993] Lustre: DEBUG MARKER: == sanity-sec test 59c: MDT migrate of encrypted files without key ========================================================== 00:42:23 (1788842543) [ 3612.496209] Lustre: DEBUG MARKER: SKIP: sanity-sec test_59c needs >= 2 MDTs [ 3614.106857] Lustre: DEBUG MARKER: == sanity-sec test 60: Subdirmount of encrypted dir ====== 00:42:28 (1788842548) [ 3618.106487] bash (93659): drop_caches: 3 [ 3621.695981] bash (93659): drop_caches: 3 [ 3633.099928] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 3633.104320] Lustre: Skipped 22 previous similar messages [ 3633.627868] bash (93659): drop_caches: 3 [ 3636.222819] Lustre: DEBUG MARKER: == sanity-sec test 61: Nodemap enforces read-only mount == 00:42:49 (1788842569) [ 3665.853739] Lustre: lustre-MDT0000-mdc-ffff9cfbc5f68800: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3665.857955] LustreError: 95252:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9cfbc5f68800: can't stat MDS #0: rc = -30 [ 3665.865940] LustreError: 95252:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9cfbc5f68800: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3668.843346] Lustre: lustre-MDT0000-mdc-ffff9cfbc69ce000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3668.855241] LustreError: 95337:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9cfbc69ce000: can't stat MDS #0: rc = -30 [ 3668.880005] LustreError: 95337:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9cfbc69ce000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3677.446648] Lustre: lustre-MDT0000-mdc-ffff9cfbc583a000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 3677.452883] LustreError: 95504:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9cfbc583a000: can't stat MDS #0: rc = -30 [ 3677.462769] LustreError: 95504:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9cfbc583a000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 3694.415915] Lustre: DEBUG MARKER: == sanity-sec test 62: e2fsck with encrypted files ======= 00:43:48 (1788842628) [ 3695.895875] Lustre: DEBUG MARKER: SKIP: sanity-sec test_62 skip ZFS backend [ 3698.328731] Lustre: DEBUG MARKER: == sanity-sec test 63: fid2path with encrypted files ===== 00:43:52 (1788842632) [ 3700.376563] Lustre: DEBUG MARKER: SKIP: sanity-sec test_63 This test needs fscrypt userspace tool [ 3702.346869] Lustre: DEBUG MARKER: == sanity-sec test 64a: Nodemap enforces file_perms RBAC roles ========================================================== 00:43:56 (1788842636) [ 3765.385134] Lustre: DEBUG MARKER: == sanity-sec test 64b: Nodemap enforces dne_ops RBAC roles ========================================================== 00:44:59 (1788842699) [ 3767.007346] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64b mdt count 1, skipping dne_ops role [ 3768.951519] Lustre: DEBUG MARKER: == sanity-sec test 64c: Nodemap enforces quota related RBAC roles ========================================================== 00:45:02 (1788842702) [ 3801.673196] LustreError: 99221:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9cfbc50cb800: ptlrpc_queue_wait failed: rc = -1 [ 3802.206352] LustreError: 99243:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9cfbc50cb800: ptlrpc_queue_wait failed: rc = -1 [ 3802.214323] LustreError: 99243:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 21 previous similar messages [ 3825.755959] LustreError: 99598:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9cfbc50cb800: ptlrpc_queue_wait failed: rc = -1 [ 3825.767509] LustreError: 99598:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 1 previous similar message [ 3855.615235] Lustre: DEBUG MARKER: == sanity-sec test 64d: Nodemap enforces byfid_ops RBAC roles ========================================================== 00:46:29 (1788842789) [ 3921.648736] Lustre: DEBUG MARKER: == sanity-sec test 64e: Nodemap enforces chlg_ops RBAC roles ========================================================== 00:47:35 (1788842855) [ 3949.199500] LustreError: 102436:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9cfbc50cb800: fail to open changelog catalog: rc = -13 [ 3975.638664] LustreError: 102884:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9cfbc50cb800: fail to open changelog catalog: rc = -13 [ 4001.152042] Lustre: DEBUG MARKER: == sanity-sec test 64f: Nodemap enforces fscrypt_admin RBAC roles ========================================================== 00:48:55 (1788842935) [ 4003.049831] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64f Need fscrypt, skip fscrypt_admin role [ 4004.735563] Lustre: DEBUG MARKER: == sanity-sec test 64g: Nodemap enforces server_upcall RBAC role ========================================================== 00:48:58 (1788842938) [ 4067.913242] Lustre: DEBUG MARKER: == sanity-sec test 64h: Nodemap enforces local_admin RBAC roles ========================================================== 00:50:01 (1788843001) [ 4090.804269] LustreError: 106105:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9cfbc50cb800: ptlrpc_queue_wait failed: rc = -1 [ 4090.807785] LustreError: 106105:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 2 previous similar messages [ 4096.185709] LustreError: 106189:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9cfbc50cb800: ptlrpc_queue_wait failed: rc = -1 [ 4118.969594] Lustre: DEBUG MARKER: == sanity-sec test 64i: Nodemap quota enforcement with local_admin RBAC and offsets ========================================================== 00:50:53 (1788843053) [ 4335.121418] Lustre: Unmounted lustre-client [ 4335.126674] Lustre: Skipped 12 previous similar messages [ 4343.041941] LustreError: 110753:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 968us [ 4343.051275] LustreError: 110753:0:(obd_config.c:1432:process_param2_config()) Skipped 12 previous similar messages [ 4343.082958] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 4343.085186] Lustre: Skipped 6 previous similar messages [ 4346.278319] Lustre: DEBUG MARKER: == sanity-sec test 64j: Nodemap enforces projid_set RBAC role ========================================================== 00:54:40 (1788843280) [ 4421.986466] Lustre: DEBUG MARKER: == sanity-sec test 64k: Nodemap enforces foreign_ops RBAC roles ========================================================== 00:55:55 (1788843355) [ 4473.495162] Lustre: DEBUG MARKER: == sanity-sec test 64l: Nodemap enforces immutable_flags RBAC role ========================================================== 00:56:47 (1788843407) [ 4526.529912] Lustre: DEBUG MARKER: == sanity-sec test 65: lfs find -printf %La and --attrs support ========================================================== 00:57:40 (1788843460) [ 4528.126181] LustreError: 114903:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9cfbeef07800: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4528.430337] Lustre: Test dummy encryption mode enabled [ 4528.436437] Lustre: Skipped 8 previous similar messages [ 4529.120284] LustreError: 114989:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9cfbc6342800: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4537.105536] LustreError: 115661:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9cfbc6342800: inode [0x20000041d:0xf:0x0] mdc close failed: rc = -1 [ 4537.118015] LustreError: 115661:0:(file.c:251:ll_close_inode_openhandle()) Skipped 1 previous similar message [ 4537.716724] bash (114723): drop_caches: 3 [ 4540.657185] Lustre: DEBUG MARKER: == sanity-sec test 68: all config logs are processed ===== 00:57:54 (1788843474) [ 4543.253440] LustreError: 2361:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d sleeping for 20000ms [ 4548.384059] LustreError: 115933:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.134@tcp: failed processing log, type 1: rc = -110 [ 4563.255431] LustreError: 2361:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d awake [ 4578.771816] Lustre: DEBUG MARKER: == sanity-sec test 69: check upcall incorrect values ===== 00:58:32 (1788843512) [ 4593.309982] Lustre: DEBUG MARKER: == sanity-sec test 70: targets have local copy of sptlrpc llog ========================================================== 00:58:47 (1788843527) [ 4595.674598] Lustre: DEBUG MARKER: SKIP: sanity-sec test_70 need shared key feature for this test [ 4597.743645] Lustre: DEBUG MARKER: == sanity-sec test 71: encryption does not remove project flag ========================================================== 00:58:51 (1788843531) [ 4599.618744] Lustre: DEBUG MARKER: SKIP: sanity-sec test_71 Need fscrypt [ 4601.693492] Lustre: DEBUG MARKER: == sanity-sec test 72a: dynamic nodemap properties on OSS ========================================================== 00:58:55 (1788843535) [ 4703.572463] Lustre: DEBUG MARKER: == sanity-sec test 72b: dynamic nodemap properties on MDS ========================================================== 01:00:37 (1788843637) [ 4801.292556] Lustre: DEBUG MARKER: == sanity-sec test 72c: child_raise_privileges nodemap property ========================================================== 01:02:15 (1788843735) [ 4850.437904] Lustre: DEBUG MARKER: == sanity-sec test 72d: fileset inheritance for dynamic nodemap ========================================================== 01:03:04 (1788843784) [ 4915.628752] Lustre: DEBUG MARKER: == sanity-sec test 72e: dynamic nodemap reclassify ======= 01:04:09 (1788843849) [ 4951.965610] Lustre: Unmounted lustre-client [ 4951.968498] Lustre: Skipped 5 previous similar messages [ 4959.880903] LustreError: 124397:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 622us [ 4959.888125] LustreError: 124397:0:(obd_config.c:1432:process_param2_config()) Skipped 5 previous similar messages [ 4959.944757] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 4959.949206] Lustre: Skipped 5 previous similar messages [ 4961.886554] Lustre: DEBUG MARKER: == sanity-sec test 72f: fileset_modify on dynamic nodemap ========================================================== 01:04:55 (1788843895) [ 5029.968540] Lustre: DEBUG MARKER: == sanity-sec test 73: encrypted names in changelogs ===== 01:06:03 (1788843963) [ 5032.248329] Lustre: DEBUG MARKER: SKIP: sanity-sec test_73 Need fscrypt [ 5034.085880] Lustre: DEBUG MARKER: == sanity-sec test 74: Set nodemap deny_mount flag ======= 01:06:08 (1788843968) [ 5060.679179] LustreError: 126607:0:(llite_lib.c:605:client_common_fill_super()) lustre-clilmv-ffff9cfbc4f44800: cannot mds_connect: rc = -1 [ 5060.720085] LustreError: 126607:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 5080.210750] Lustre: DEBUG MARKER: == sanity-sec test 75: check uid/gid/projid are set on OST and MDT for various RPCs ========================================================== 01:06:54 (1788844014) [ 5082.567362] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75 ldiskfs only test (using debugfs) [ 5085.219470] Lustre: DEBUG MARKER: == sanity-sec test 75a: test resource fs IDs against nodemap offset ========================================================== 01:06:58 (1788844018) [ 5090.475430] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75a need at least two clients [ 5092.822645] Lustre: DEBUG MARKER: == sanity-sec test 75b: test resource ID repair ========== 01:07:06 (1788844026) [ 5095.727547] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75b ldiskfs only test (using debugfs) [ 5097.682412] Lustre: DEBUG MARKER: == sanity-sec test 76: suppgroups and gid mapping ======== 01:07:11 (1788844031) [ 5140.829941] Lustre: DEBUG MARKER: == sanity-sec test 77: root offsetting =================== 01:07:54 (1788844074) [ 5185.540913] Lustre: DEBUG MARKER: == sanity-sec test 78: nodemap stats ===================== 01:08:39 (1788844119) [ 5223.557604] Lustre: DEBUG MARKER: == sanity-sec test 79: ssk for nodemap identification ==== 01:09:17 (1788844157) [ 5225.013298] Lustre: DEBUG MARKER: SKIP: sanity-sec test_79 Need shared key feature for this test [ 5226.799699] Lustre: DEBUG MARKER: == sanity-sec test 81a: nodemap ban list ================= 01:09:20 (1788844160) [ 5228.416926] Lustre: DEBUG MARKER: test_81a 15730 [ 5248.440314] Lustre: This client was banned by administrative request for file system lustre. All requests will get Operation not permitted. [ 5248.453373] LustreError: 132618:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5282.732436] LustreError: 133196:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5282.738574] LustreError: 133196:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5301.729773] LustreError: 133422:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.134@tcp: failed processing log, type 1: rc = -110 [ 5439.459161] LustreError: MGC192.168.202.134@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 5439.470993] LustreError: 133422:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 5451.955297] LustreError: 133665:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 5451.972183] LustreError: 133665:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 5457.823381] LustreError: 133702:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.134@tcp: failed processing log, type 1: rc = -110 [ 5595.103427] LustreError: MGC192.168.202.134@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 5595.122865] Lustre: Unmounted lustre-client [ 5595.130935] Lustre: Skipped 10 previous similar messages [ 5595.139494] LustreError: 133702:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 5597.050658] LustreError: 133792:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 961us [ 5597.065680] LustreError: 133792:0:(obd_config.c:1432:process_param2_config()) Skipped 8 previous similar messages [ 5597.103460] Lustre: Mounted lustre-client - version 2.17.57_115_g0321d60 [ 5597.106385] Lustre: Skipped 7 previous similar messages [ 5616.265846] Lustre: DEBUG MARKER: == sanity-sec test 81b: banned client does not block other ========================================================== 01:15:50 (1788844550) [ 5617.955032] Lustre: DEBUG MARKER: SKIP: sanity-sec test_81b Need 2 clients [ 5619.327942] Lustre: DEBUG MARKER: == sanity-sec test 82: export lock revoked after nodemap change ========================================================== 01:15:53 (1788844553) [ 5684.538121] Lustre: DEBUG MARKER: == sanity-sec test 83: Suppgids for cross-MDT ops ======== 01:16:58 (1788844618) [ 5686.278484] Lustre: DEBUG MARKER: SKIP: sanity-sec test_83 needs >= 2 MDTs [ 5688.384171] Lustre: DEBUG MARKER: == sanity-sec test 84: do not squash trusted ids ========= 01:17:02 (1788844622) [ 5729.662972] Lustre: DEBUG MARKER: == sanity-sec test 85: forbid squashing to UID/GID 0 ===== 01:17:43 (1788844663) [ 5773.121117] Lustre: DEBUG MARKER: == sanity-sec test 93: incremental RBAC role modifications ========================================================== 01:18:27 (1788844707) [ 5850.096877] Lustre: DEBUG MARKER: == sanity-sec test 100: SSK automatic prime generation, binary/ASCII server keys ========================================================== 01:19:44 (1788844784) [ 5853.348964] Lustre: DEBUG MARKER: SKIP: sanity-sec test_100 Need shared key feature for this test [ 5855.856746] Lustre: DEBUG MARKER: == sanity-sec test 101: lgss_sk -a and -l support for ascii-encoded SSK keys ========================================================== 01:19:49 (1788844789) [ 5857.838587] Lustre: DEBUG MARKER: SKIP: sanity-sec test_101 Need shared key feature for this test [ 5859.619457] Lustre: DEBUG MARKER: == sanity-sec test 102: SSK automatic key loading from mount point ========================================================== 01:19:53 (1788844793) [ 5861.202290] Lustre: DEBUG MARKER: SKIP: sanity-sec test_102 Need shared key feature for this test [ 5863.105989] Lustre: DEBUG MARKER: == sanity-sec test 103: Multiple SSK keys on server side ========================================================== 01:19:57 (1788844797) [ 5864.874805] Lustre: DEBUG MARKER: SKIP: sanity-sec test_103 Need shared key feature for this test [ 5867.233486] Lustre: DEBUG MARKER: == sanity-sec test 104: SSK key removal from keyring ===== 01:20:00 (1788844800) [ 5869.147766] Lustre: DEBUG MARKER: SKIP: sanity-sec test_104 Need shared key feature for this test [ 5871.394776] Lustre: DEBUG MARKER: == sanity-sec test 105: update nodemap membership on flavor change ========================================================== 01:20:05 (1788844805) [ 5873.266779] Lustre: DEBUG MARKER: SKIP: sanity-sec test_105 Need shared key feature for this test [ 5875.709599] Lustre: DEBUG MARKER: == sanity-sec test 106: switch nodemap to gssonly ======== 01:20:09 (1788844809) [ 5877.732567] Lustre: DEBUG MARKER: SKIP: sanity-sec test_106 Need shared key feature for this test [ 5879.569876] Lustre: DEBUG MARKER: == sanity-sec test 200: sk_load_key broadens SSK key perms without @u linked ========================================================== 01:20:13 (1788844813) [ 5881.423549] Lustre: DEBUG MARKER: SKIP: sanity-sec test_200 Need shared key feature for this test [ 5883.233051] Lustre: DEBUG MARKER: == sanity-sec test 300: test user_principal mount option parsing ========================================================== 01:20:17 (1788844817) [ 5885.157267] Lustre: DEBUG MARKER: Mount with user_principal=mock_iam_test [ 5892.744028] Lustre: DEBUG MARKER: Mount with only user_principal (should fail) [ 5893.147373] LustreError: Unknown option 'user_principal', won't mount. [ 5893.178786] LustreError: 143151:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -22 [ 5894.827893] Lustre: DEBUG MARKER: Mount failed as expected with only -o user_principal [ 5901.437343] Lustre: DEBUG MARKER: cleanup: ====================================================== [ 5903.222668] Lustre: DEBUG MARKER: == sanity-sec test complete, duration 5662 sec =========== 01:20:37 (1788844837) [ 5905.258963] Lustre: DEBUG MARKER: === sanity-sec: start cleanup 01:20:39 (1788844839) === [ 5909.406262] Lustre: DEBUG MARKER: === sanity-sec: finish cleanup 01:20:43 (1788844843) === [ 5947.179304] Key type lgssc unregistered [ 5947.506891] LNet: 144918:0:(lib-ptl.c:964:lnet_clear_lazy_portal()) Active lazy portal 0 on exit [ 5947.519818] LNetError: 144918:0:(acceptor.c:252:lnet_acceptor_remove_socket()) Interface ens2 not found [ 5947.533360] LNet: Removed LNI 192.168.202.34@tcp [ 5948.303275] Key type .llcrypt unregistered [ 5948.306135] Key type ._llcrypt unregistered