[ 0.000000] Linux version 4.18.0rh8.10-debug (green@maintenance) (gcc version 8.5.0 20210514 (Red Hat 8.5.0-26) (GCC)) #2 SMP Mon Jul 14 01:24:22 EDT 2025 [ 0.000000] Command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.000000] signal: max sigframe size: 1776 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffd9fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bffda000-0x00000000bfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000146dfffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.8 present. [ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-10.fc44 06/10/2025 [ 0.000000] Hypervisor detected: KVM [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00 [ 0.000000] kvm-clock: using sched offset of 456768831 cycles [ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.000000] tsc: Detected 2399.998 MHz processor [ 0.000000] last_pfn = 0x146e00 max_arch_pfn = 0x400000000 [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] last_pfn = 0xbffda max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f54d0-0x000f54df] [ 0.000000] RAMDISK: [mem 0xbcc64000-0xbffcffff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F52F0 000014 (v00 BOCHS ) [ 0.000000] ACPI: RSDT 0x00000000BFFE2464 000034 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACP 0x00000000BFFE2300 000074 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: DSDT 0x00000000BFFE0040 0022C0 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: FACS 0x00000000BFFE0000 000040 [ 0.000000] ACPI: APIC 0x00000000BFFE2374 000090 (v03 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: HPET 0x00000000BFFE2404 000038 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: WAET 0x00000000BFFE243C 000028 (v01 BOCHS BXPC 00000001 BXPC 00000001) [ 0.000000] ACPI: Reserving FACP table memory at [mem 0xbffe2300-0xbffe2373] [ 0.000000] ACPI: Reserving DSDT table memory at [mem 0xbffe0040-0xbffe22ff] [ 0.000000] ACPI: Reserving FACS table memory at [mem 0xbffe0000-0xbffe003f] [ 0.000000] ACPI: Reserving APIC table memory at [mem 0xbffe2374-0xbffe2403] [ 0.000000] ACPI: Reserving HPET table memory at [mem 0xbffe2404-0xbffe243b] [ 0.000000] ACPI: Reserving WAET table memory at [mem 0xbffe243c-0xbffe2463] [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000146dfffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x1465a3000-0x1465cdfff] [ 0.000000] Reserving 256MB of memory at 2752MB for crashkernel (System RAM: 4205MB) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000bffd9fff] [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000146dfffff] [ 0.000000] Zeroed struct page in unavailable ranges: 4744 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000146dfffff] [ 0.000000] ACPI: PM-Timer IO Port: 0x608 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] TSC deadline timer available [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] kvm-guest: KVM setup pv remote TLB flush [ 0.000000] kvm-guest: setup PV sched yield [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbffda000-0xbfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfeffbfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeffc000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] [mem 0xc0000000-0xfeffbfff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on KVM [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.000000] kvm-guest: PV spinlocks enabled [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1059618 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: rd.shell root=nbd:192.168.200.253:rocky8.10:ext4:ro:-p,-b4096 ro crashkernel=256M panic=1 nomodeset ipmtu=9000 ip=dhcp rd.neednet=1 init_on_free=off mitigations=off console=ttyS1,115200 audit=0 [ 0.000000] Specific versions of hardware are certified with Red Hat Enterprise Linux 8. Please see the list of hardware certified with Red Hat Enterprise Linux 8 at https://catalog.redhat.com. [ 0.000000] audit: disabled (until reboot) [ 0.000000] software IO TLB: area num 4. [ 0.000000] Memory: 2829700K/4306400K available (18435K kernel code, 11221K rwdata, 7248K rodata, 2908K init, 18040K bss, 524580K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] ftrace: allocating 41240 entries in 162 pages [ 0.000000] ftrace: allocated 162 pages with 3 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.000000] rcu: RCU callback double-/use-after-free debug enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x622/0x9a8 with crng_init=0 [ 0.001000] Console: colour *CGA 80x25 [ 0.001000] printk: console [ttyS1] enabled [ 0.001000] ACPI: Core revision 20220331 [ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.001014] APIC: Switch to symmetric I/O mode setup [ 0.003044] x2apic enabled [ 0.004008] Switched APIC routing to physical x2apic. [ 0.005014] kvm-guest: setup PV IPIs [ 0.007996] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.008000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 0.008033] Calibrating delay loop (skipped) preset value.. 4799.99 BogoMIPS (lpj=2399998) [ 0.009011] pid_max: default: 32768 minimum: 301 [ 0.010163] LSM: Security Framework initializing [ 0.011090] Yama: becoming mindful. [ 0.012037] SELinux: Initializing. [ 0.013085] *** VALIDATE selinux *** [ 0.022806] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc) [ 0.027205] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc) [ 0.028209] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.029100] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc) [ 0.030148] *** VALIDATE tmpfs *** [ 0.031545] *** VALIDATE proc *** [ 0.032291] *** VALIDATE cgroup *** [ 0.033011] *** VALIDATE cgroup2 *** [ 0.034325] x86/cpu: User Mode Instruction Prevention (UMIP) activated [ 0.035230] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.036013] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.037050] Spectre V2 : User space: Vulnerable [ 0.038012] Speculative Store Bypass: Vulnerable [ 0.041342] debug: unmapping init [mem 0xffffffffbe059000-0xffffffffbe060fff] [ 0.044201] smpboot: CPU0: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz (family: 0x6, model: 0x3e, stepping: 0x4) [ 0.045693] Performance Events: IvyBridge events, full-width counters, Intel PMU driver. [ 0.046032] ... version: 2 [ 0.047014] ... bit width: 48 [ 0.048015] ... generic registers: 4 [ 0.049012] ... value mask: 0000ffffffffffff [ 0.050016] ... max period: 00007fffffffffff [ 0.051010] ... fixed-purpose events: 3 [ 0.051905] ... event mask: 000000070000000f [ 0.052362] rcu: Hierarchical SRCU implementation. [ 0.054639] smp: Bringing up secondary CPUs ... [ 0.055677] x86: Booting SMP configuration: [ 0.056034] .... node #0, CPUs: #1 #2 #3 [ 0.059235] smp: Brought up 1 node, 4 CPUs [ 0.061016] smpboot: Max logical packages: 1 [ 0.062029] smpboot: Total of 4 processors activated (19199.98 BogoMIPS) [ 0.142045] node 0 deferred pages initialised in 77ms [ 0.146128] devtmpfs: initialized [ 0.147442] x86/mm: Memory block size: 128MB [ 0.151000] gcov: version magic: 0x41383552 [ 0.154408] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.157124] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc) [ 0.160425] pinctrl core: initialized pinctrl subsystem [ 0.162216] [ 0.162866] ************************************************************* [ 0.165020] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.168022] ** ** [ 0.170013] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 0.173023] ** ** [ 0.175019] ** This means that this kernel is built to expose internal ** [ 0.178018] ** IOMMU data structures, which may compromise security on ** [ 0.180013] ** your system. ** [ 0.183017] ** ** [ 0.185011] ** If you see this message and you are not debugging the ** [ 0.187015] ** kernel, report this immediately to your vendor! ** [ 0.189023] ** ** [ 0.192013] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.195016] ************************************************************* [ 0.198715] NET: Registered protocol family 16 [ 0.200652] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.203089] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.206097] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.210017] cpuidle: using governor menu [ 0.211814] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.213767] PCI: Using configuration type 1 for base access [ 0.216161] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on [ 0.225061] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.227056] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.229279] cryptd: max_cpu_qlen set to 1000 [ 0.232197] ACPI: Added _OSI(Module Device) [ 0.234019] ACPI: Added _OSI(Processor Device) [ 0.235017] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.236017] ACPI: Added _OSI(Processor Aggregator Device) [ 0.241244] ACPI: 1 ACPI AML tables successfully acquired and loaded [ 0.248430] ACPI: Interpreter enabled [ 0.250115] ACPI: PM: (supports S0 S3 S4 S5) [ 0.252023] ACPI: Using IOAPIC for interrupt routing [ 0.254201] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.257608] ACPI: Enabled 2 GPEs in block 00 to 0F [ 0.269875] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.272045] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI HPX-Type3] [ 0.275036] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI] [ 0.278318] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.283641] acpiphp: Slot [2] registered [ 0.285118] acpiphp: Slot [5] registered [ 0.286284] acpiphp: Slot [6] registered [ 0.288176] acpiphp: Slot [3] registered [ 0.290187] acpiphp: Slot [4] registered [ 0.291112] acpiphp: Slot [7] registered [ 0.293144] acpiphp: Slot [8] registered [ 0.294096] acpiphp: Slot [9] registered [ 0.297360] acpiphp: Slot [10] registered [ 0.300165] acpiphp: Slot [11] registered [ 0.302216] acpiphp: Slot [12] registered [ 0.303180] acpiphp: Slot [13] registered [ 0.305212] acpiphp: Slot [14] registered [ 0.309312] acpiphp: Slot [15] registered [ 0.312373] acpiphp: Slot [16] registered [ 0.316177] acpiphp: Slot [17] registered [ 0.317210] acpiphp: Slot [18] registered [ 0.319177] acpiphp: Slot [19] registered [ 0.321176] acpiphp: Slot [20] registered [ 0.322160] acpiphp: Slot [21] registered [ 0.324165] acpiphp: Slot [22] registered [ 0.326178] acpiphp: Slot [23] registered [ 0.328192] acpiphp: Slot [24] registered [ 0.330233] acpiphp: Slot [25] registered [ 0.331163] acpiphp: Slot [26] registered [ 0.333153] acpiphp: Slot [27] registered [ 0.335182] acpiphp: Slot [28] registered [ 0.336202] acpiphp: Slot [29] registered [ 0.338176] acpiphp: Slot [30] registered [ 0.340084] acpiphp: Slot [31] registered [ 0.341089] PCI host bridge to bus 0000:00 [ 0.343034] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.348043] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.354056] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.359070] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.362064] pci_bus 0000:00: root bus resource [mem 0xe0000000000-0xe007fffffff window] [ 0.366056] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.368244] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.373194] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.376501] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180 [ 0.383515] pci 0000:00:01.1: reg 0x20: [io 0xc120-0xc12f] [ 0.387051] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.390048] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.392025] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.395029] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.398000] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000 [ 0.405111] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI [ 0.411090] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB [ 0.416193] pci 0000:00:01.3: quirk_piix4_acpi+0x0/0x1e0 took 10742 usecs [ 0.422408] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 [ 0.431019] pci 0000:00:02.0: reg 0x10: [io 0xc100-0xc11f] [ 0.448029] pci 0000:00:02.0: reg 0x20: [mem 0xe0000000000-0xe0000003fff 64bit pref] [ 0.452017] pci 0000:00:02.0: reg 0x30: [mem 0xfeb80000-0xfebbffff pref] [ 0.460745] pci 0000:00:05.0: [1af4:1001] type 00 class 0x010000 [ 0.497051] pci 0000:00:05.0: reg 0x10: [io 0xc000-0xc07f] [ 0.503022] pci 0000:00:05.0: reg 0x14: [mem 0xfebc0000-0xfebc0fff] [ 0.575060] pci 0000:00:05.0: reg 0x20: [mem 0xe0000004000-0xe0000007fff 64bit pref] [ 0.590417] pci 0000:00:06.0: [1af4:1001] type 00 class 0x010000 [ 0.610031] pci 0000:00:06.0: reg 0x10: [io 0xc080-0xc0ff] [ 0.625040] pci 0000:00:06.0: reg 0x14: [mem 0xfebc1000-0xfebc1fff] [ 0.663046] pci 0000:00:06.0: reg 0x20: [mem 0xe0000008000-0xe000000bfff 64bit pref] [ 0.685432] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.687501] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 0.689446] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 0.692487] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 0.694318] ACPI: PCI: Interrupt link LNKS configured for IRQ 9 [ 0.701028] iommu: Default domain type: Passthrough [ 0.704573] SCSI subsystem initialized [ 0.707310] ACPI: bus type USB registered [ 0.709232] usbcore: registered new interface driver usbfs [ 0.711145] usbcore: registered new interface driver hub [ 0.713164] usbcore: registered new device driver usb [ 0.715279] pps_core: LinuxPPS API ver. 1 registered [ 0.717021] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.720102] PTP clock support registered [ 0.722153] EDAC MC: Ver: 3.0.0 [ 0.724304] PCI: Using ACPI for IRQ routing [ 0.727025] NetLabel: Initializing [ 0.729018] NetLabel: domain hash size = 128 [ 0.730016] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.732119] NetLabel: unlabeled traffic allowed by default [ 0.734143] vgaarb: loaded [ 0.735403] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.737029] hpet0: 3 comparators, 64-bit 100.000000 MHz counter [ 0.743230] clocksource: Switched to clocksource kvm-clock [ 0.932291] VFS: Disk quotas dquot_6.6.0 [ 0.935361] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.941902] *** VALIDATE ramfs *** [ 0.945227] *** VALIDATE hugetlbfs *** [ 0.949096] pnp: PnP ACPI init [ 0.955210] pnp: PnP ACPI: found 6 devices [ 0.982208] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.985213] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.987802] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.989955] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.992024] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.994138] pci_bus 0000:00: resource 8 [mem 0xe0000000000-0xe007fffffff window] [ 0.997231] NET: Registered protocol family 2 [ 0.999810] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc) [ 1.004266] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, vmalloc) [ 1.009705] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc) [ 1.016152] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc) [ 1.022054] TCP: Hash tables configured (established 65536 bind 65536) [ 1.026238] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, vmalloc) [ 1.030774] UDP hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 1.034697] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, vmalloc) [ 1.039155] NET: Registered protocol family 1 [ 1.042871] RPC: Registered named UNIX socket transport module. [ 1.044827] RPC: Registered udp transport module. [ 1.046545] RPC: Registered tcp transport module. [ 1.047961] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.050179] NET: Registered protocol family 44 [ 1.051916] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 1.053691] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 1.055564] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 1.059677] PCI: CLS 0 bytes, default 64 [ 1.061109] Unpacking initramfs... [ 2.521489] debug: unmapping init [mem 0xffff9f313cc64000-0xffff9f313ffcffff] [ 2.525346] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 2.527775] software IO TLB: mapped [mem 0x00000000a8000000-0x00000000ac000000] (64MB) [ 2.530891] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x229835b7123, max_idle_ns: 440795242976 ns [ 3.029174] Initialise system trusted keyrings [ 3.031627] Key type blacklist registered [ 3.034201] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 3.045314] zbud: loaded [ 3.048218] *** VALIDATE nfs *** [ 3.049756] *** VALIDATE nfs4 *** [ 3.051393] pstore: using deflate compression [ 3.054518] Platform Keyring initialized [ 3.173344] NET: Registered protocol family 38 [ 3.175919] Key type asymmetric registered [ 3.177720] Asymmetric key parser 'x509' registered [ 3.179796] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 3.183456] io scheduler mq-deadline registered [ 3.185152] io scheduler kyber registered [ 3.186655] io scheduler bfq registered [ 3.188777] atomic64_test: passed for x86-64 platform with CX8 and with SSE [ 3.191488] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 3.194419] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 3.197378] ACPI: Power Button [PWRF] [ 3.202939] ACPI: \_SB_.LNKB: Enabled at IRQ 10 [ 3.209053] ACPI: \_SB_.LNKA: Enabled at IRQ 11 [ 3.218266] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.246198] 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 3.274816] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 3.279812] Non-volatile memory driver v1.3 [ 3.281968] Linux agpgart interface v0.103 [ 3.315908] virtio_blk virtio1: [vda] 149944 512-byte logical blocks (76.8 MB/73.2 MiB) [ 3.319194] vda: detected capacity change from 0 to 76771328 [ 3.338140] virtio_blk virtio2: [vdb] 2097152 512-byte logical blocks (1.07 GB/1.00 GiB) [ 3.342474] vdb: detected capacity change from 0 to 1073741824 [ 3.349670] libphy: Fixed MDIO Bus: probed [ 3.355955] usbcore: registered new interface driver usbserial_generic [ 3.359339] usbserial: USB Serial support registered for generic [ 3.362122] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 3.368344] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.370925] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.374217] mousedev: PS/2 mouse device common for all mice [ 3.377350] rtc_cmos 00:05: RTC can wake from S4 [ 3.380733] rtc_cmos 00:05: registered as rtc0 [ 3.382497] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 3.384871] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs [ 3.387955] intel_pstate: CPU model not supported [ 3.391710] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input4 [ 3.392178] hid: raw HID events driver (C) Jiri Kosina [ 3.396565] usbcore: registered new interface driver usbhid [ 3.398591] usbhid: USB HID core driver [ 3.400684] input: VirtualPS/2 VMware VMMouse as /devices/platform/i8042/serio1/input/input3 [ 3.401537] drop_monitor: Initializing network drop monitor service [ 3.406343] Initializing XFRM netlink socket [ 3.408454] NET: Registered protocol family 10 [ 3.411489] Segment Routing with IPv6 [ 3.413694] NET: Registered protocol family 17 [ 3.416542] mpls_gso: MPLS GSO support [ 3.421659] RAS: Correctable Errors collector initialized. [ 3.422951] AVX version of gcm_enc/dec engaged. [ 3.423936] AES CTR mode by8 optimization enabled [ 3.504516] sched_clock: Marking stable (3504496867, 0)->(4394487838, -889990971) [ 3.507081] registered taskstats version 1 [ 3.508775] Loading compiled-in X.509 certificates [ 3.510633] zswap: loaded using pool lzo/zbud [ 3.536377] Key type big_key registered [ 3.548641] Key type encrypted registered [ 3.550353] ima: No TPM chip found, activating TPM-bypass! [ 3.552450] ima: Allocated hash algorithm: sha1 [ 3.554225] ima: No architecture policies found [ 3.555989] evm: Initialising EVM extended attributes: [ 3.558144] evm: security.selinux [ 3.559388] evm: security.ima [ 3.560503] evm: security.capability [ 3.561878] evm: HMAC attrs: 0x1 [ 3.564257] rtc_cmos 00:05: setting system clock to 2026-09-16 15:22:27 UTC (1789572147) [ 3.569989] debug: unmapping init [mem 0xffffffffbf003000-0xffffffffbf1fffff] [ 3.572586] debug: unmapping init [mem 0xffffffffbdd82000-0xffffffffbe058fff] [ 3.580168] Write protecting the kernel read-only data: 28672k [ 3.582575] debug: unmapping init [mem 0xffffffffbc403000-0xffffffffbc5fffff] [ 3.585431] debug: unmapping init [mem 0xffffffffbcd14000-0xffffffffbcdfffff] [ 3.616209] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 3.624121] systemd[1]: Detected virtualization kvm. [ 3.625760] systemd[1]: Detected architecture x86-64. [ 3.627598] systemd[1]: Running in initial RAM disk. Welcome to Rocky Linux 8.10 (Green Obsidian) dracut-049-233.git20240115.el8 (Initramfs)! [ 3.653275] systemd[1]: No hostname configured. [ 3.654941] systemd[1]: Set hostname to . [ 3.656496] random: systemd: uninitialized urandom read (16 bytes read) [ 3.659026] systemd[1]: Initializing machine ID from random generator. [ 3.788428] random: systemd: uninitialized urandom read (16 bytes read) [ 3.791162] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 3.795385] random: systemd: uninitialized urandom read (16 bytes read) [ 3.796916] systemd[1]: Reached target Initrd Root Device. [ OK ] Reached target Initrd Root Device. [ 3.801208] systemd[1]: Reached target Timers. [ OK ] Reached target Timers. [ OK ] Listening on Journal Socket. Starting Journal Service... Starting Apply Kernel Variables... [ OK ] Listening on udev Control Socket. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Sockets. Starting Create list of required st…ce nodes for the current kernel... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Memstrack Anylazing Service. Starting Setup Virtual Console... [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create list of required sta…vice nodes for the current kernel. Starting Create Static Device Nodes in /dev... [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Setup Virtual Console. Starting dracut cmdline hook... [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started dracut cmdline hook. Starting dracut pre-udev hook... [ 4.482225] device-mapper: uevent: version 1.0.3 [ 4.485357] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ OK ] Started dracut pre-udev hook. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook. Starting udev Coldplug all Devices... Mounting Kernel Configuration File System... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting dracut initqueue hook... [ 5.236927] scsi host0: ata_piix [ 5.249110] scsi host1: ata_piix [ 5.284470] virtio_net virtio0 ens2: renamed from eth0 [ 5.332636] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc120 irq 14 [ 5.336390] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc128 irq 15 [ 9.052528] dracut-initqueue[581]: RTNETLINK answers: File exists [ 10.067232] random: crng init done [ 10.068489] random: 7 urandom warning(s) missed due to ratelimiting Starting nbd nbd0... [ OK ] Started nbd nbd0. [ OK ] Started dracut initqueue hook. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting /sysroot... [ 10.538733] EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted /sysroot. [ OK ] Reached target Initrd Root File System. Starting Reload Configuration from the Real Root... [ OK ] Started Reload Configuration from the Real Root. [ OK ] Reached target Initrd File Systems. [ OK ] Reached target Initrd Default Target. Starting dracut pre-pivot and cleanup hook... [ OK ] Started dracut pre-pivot and cleanup hook. Starting Cleaning Up and Shutting Down Daemons... [ OK ] Stopped dracut pre-pivot and cleanup hook. [ OK ] Stopped target Timers. [ OK ] Stopped target Initrd Default Target. [ OK ] Stopped target Initrd Root Device. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped dracut initqueue hook. Stopping Hardware RNG Entropy Gatherer Daemon... [ OK ] Stopped Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Cleaning Up and Shutting Down Daemons. [ OK ] Stopped target Basic System. [ OK ] Stopped target Slices. [ OK ] Stopped target Sockets. [ OK ] Stopped target Paths. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped target Swap. [ OK ] Stopped udev Coldplug all Devices. [ OK ] Stopped dracut pre-trigger hook. Stopping udev Kernel Device Manager... [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. [ OK ] Stopped udev Kernel Device Manager. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create list of required sta…vice nodes for the current kernel. [ OK ] Stopped dracut pre-udev hook. [ OK ] Stopped dracut cmdline hook. [ OK ] Closed udev Control Socket. [ OK ] Closed udev Kernel Socket. Starting Cleanup udevd DB... [ OK ] Started Cleanup udevd DB. [ OK ] Reached target Switch Root. Starting Switch Root... [ 11.823248] printk: systemd: 24 output lines suppressed due to ratelimiting [ 12.101088] SELinux: Disabled at runtime. [ 12.168927] systemd[1]: systemd 239 (239-82.el8_10.5) running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=legacy) [ 12.177407] systemd[1]: Detected virtualization kvm. [ 12.179270] systemd[1]: Detected architecture x86-64. Welcome to Rocky Linux 8.10 (Green Obsidian)! [ 12.729256] systemd[1]: initrd-switch-root.service: Succeeded. [ 12.733426] systemd[1]: Stopped Switch Root. [ OK ] Stopped Switch Root. [ 12.740543] systemd[1]: systemd-journald.service: Service has no hold-off time (RestartSec=0), scheduling restart. [ 12.745145] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1. [ 12.749211] systemd[1]: Stopped Journal Service. [ OK ] Stopped Journal Service. [ 12.759677] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.764611] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. Activating swap /dev/disk/by-label/SWAP... [ OK ] Listening on udev Kernel Socket. Mounting Kernel Debug File System... [ OK ] Created slice system-getty.slice. Starting Create list of required st…ce nodes for the current kernel... [ 12.819932] Adding 1048572k swap on /dev/vdb. Priority:-2 extents:1 across:1048572k FS Mounting POSIX Message Queue File System... [ OK ] Stopped target Switch Root. [ OK ] Stopped target Initrd File Systems. [ OK ] Stopped target Initrd Root File System. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target RPC Port Mapper. Mounting Huge Pages File System... [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Created slice system-sshd\x2dkeygen.slice. [ OK ] Reached target rpc_pipefs.target. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. Starting Apply Kernel Variables... [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... [ OK ] Created slice system-serial\x2dgetty.slice. [FAILED] Failed to set up automount Arbitrar…rmats File System Automount Point. See 'systemctl status proc-sys-fs-binfmt_misc.automount' for details. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. Starting Remount Root and Kernel File Systems... [ OK ] Listening on Process Core Dump Socket. [ OK ] Started Journal Service. [ OK ] Activated swap /dev/disk/by-label/SWAP. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Remount Root and Kernel File Systems. See 'systemctl status systemd-remount-fs.service' for details. Starting Configure read-only root support... Starting Create Static Device Nodes in /dev... [ OK ] Reached target Swap. Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /mnt... Mounting /home/green/git/lustre-release... [ OK ] Started udev Coldplug all Devices. [ OK ] Mounted /mnt. [ 13.318268] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ OK ] Mounted /home/green/git/lustre-release. [ OK ] Started udev Kernel Device Manager. [ 13.630279] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0 [ 13.755602] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 13.815086] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer [ 13.826058] EDAC sbridge: Ver: 1.1.2 [ 15.168226] Key type dns_resolver registered [ 15.474589] NFS: Registering the id_resolver key type [ 15.476484] Key type id_resolver registered [ 15.479510] Key type id_legacy registered [ OK ] Started Configure read-only root support. [ OK ] Reached target Local File Systems. Starting Mark the need to relabel after reboot... Starting Rebuild Dynamic Linker Cache... Starting Create Volatile Files and Directories... Starting Load/Save Random Seed... [ OK ] Started Mark the need to relabel after reboot. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting RPC Bind... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started RPC Bind. [ OK ] Started Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Started Update is Completed. [ OK ] Reached target System Initialization. [ OK ] Started daily update of the root trust anchor for DNSSEC. [ OK ] Started dnf makecache --timer. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started irqbalance daemon. Starting Restore /run/initramfs on shutdown... [ OK ] Reached target sshd-keygen.target. Starting Login Service... [ OK ] Started D-Bus System Message Bus. Starting Network Manager... [ OK ] Started Restore /run/initramfs on shutdown. [ OK ] Started Login Service. [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting Dynamic System Tuning Daemon... Starting OpenSSH server daemon... Starting GSSAPI Proxy Daemon... Starting Network Manager Wait Online... Starting Hostname Service... [ OK ] Started GSSAPI Proxy Daemon. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started OpenSSH server daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Command Scheduler. [ OK ] Started Serial Getty on ttyS1. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started Hostname Service. Starting Network Manager Script Dispatcher Service... [ OK ] Started Network Manager Script Dispatcher Service. [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting Notify NFS peers of a restart... Starting Crash recovery kernel arming... Starting System Logging Service... [ OK ] Started Notify NFS peers of a restart. [ OK ] Started System Logging Service. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Started Dynamic System Tuning Daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Rocky Linux 8.10 (Green Obsidian) Kernel 4.18.0rh8.10-debug on an x86_64 oleg218-client login: [ 55.380363] libcfs: loading out-of-tree module taints kernel. [ 55.555132] Key type ._llcrypt registered [ 55.556937] Key type .llcrypt registered [ 55.960348] libcfs: HW NUMA nodes: 1, HW CPU cores: 4, npartitions: 2 [ 55.974436] alg: No test for adler32 (adler32-zlib) [ 57.368681] Lustre: Lustre: Build Version: 2.17.58_39_g6aa67ea [ 58.042436] LNet: Added LNI 192.168.202.18@tcp [8/256/0/180] [ 59.775295] Key type lgssc registered [ 61.505296] Lustre: Echo OBD driver; http://www.lustre.org/ [ 171.651098] hrtimer: interrupt took 8227110 ns [ 274.583869] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 280.337190] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 295.558426] Lustre: DEBUG MARKER: oleg218-client.virtnet: executing check_logdir /tmp/testlogs/ [ 300.511296] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 23s idle [ 301.294400] Lustre: DEBUG MARKER: oleg218-client.virtnet: executing yml_node [ 306.232589] Lustre: DEBUG MARKER: Client: 2.17.58.39 [ 309.216241] Lustre: DEBUG MARKER: MDS: 2.17.58.39 [ 312.319507] Lustre: DEBUG MARKER: OSS: 2.17.58.39 [ 314.028627] Lustre: DEBUG MARKER: -----============= acceptance-small: sanity-sec ============----- Wed Sep 16 11:27:36 EDT 2026 [ 333.226881] Lustre: DEBUG MARKER: excepting tests: 27 [ 334.792343] Lustre: DEBUG MARKER: skipping tests SLOW=no: 26 [ 337.801560] Lustre: DEBUG MARKER: === sanity-sec: start setup 11:27:59 (1789572479) === [ 344.390983] Lustre: DEBUG MARKER: oleg218-client.virtnet: executing check_config_client /mnt/lustre [ 366.869614] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 381.014239] Lustre: DEBUG MARKER: === sanity-sec: finish setup 11:28:43 (1789572523) === [ 390.595348] Lustre: DEBUG MARKER: == sanity-sec test 0: uid permission ======================================================================================= 11:28:52 (1789572532) [ 400.466982] Lustre: DEBUG MARKER: == sanity-sec test 1: setuid/gid ======================================================================================= 11:29:02 (1789572542) [ 402.442091] Lustre: DEBUG MARKER: SKIP: sanity-sec test_1 without GSS support. [ 405.043926] Lustre: DEBUG MARKER: == sanity-sec test 4: set supplementary group ========================================================================= 11:29:06 (1789572546) [ 413.154599] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 22s idle [ 413.166412] Lustre: Skipped 1 previous similar message [ 416.209327] Lustre: DEBUG MARKER: == sanity-sec test 5: Test l_getidentity with a nonexistent user on the MDT ========================================================== 11:29:18 (1789572558) [ 448.501167] Lustre: DEBUG MARKER: == sanity-sec test 7: nodemap create and delete ========== 11:29:50 (1789572590) [ 486.992103] Lustre: DEBUG MARKER: == sanity-sec test 8: nodemap reject duplicates ========== 11:30:29 (1789572629) [ 542.194849] Lustre: DEBUG MARKER: == sanity-sec test 9: nodemap range add ================== 11:31:23 (1789572683) [ 590.976680] Lustre: DEBUG MARKER: == sanity-sec test 10a: nodemap reject duplicate ranges == 11:32:13 (1789572733) [ 651.459571] Lustre: DEBUG MARKER: == sanity-sec test 10b: delete range from the correct nodemap ========================================================== 11:33:13 (1789572793) [ 671.006714] Lustre: DEBUG MARKER: == sanity-sec test 10c: verfify contiguous range support ========================================================== 11:33:33 (1789572813) [ 684.281615] Lustre: DEBUG MARKER: == sanity-sec test 10d: verfify nodemap range format '*@' support ========================================================== 11:33:46 (1789572826) [ 699.899884] Lustre: DEBUG MARKER: == sanity-sec test 11: nodemap modify ==================== 11:34:01 (1789572841) [ 749.285969] Lustre: DEBUG MARKER: == sanity-sec test 12: nodemap set squash ids ============ 11:34:51 (1789572891) [ 793.783938] Lustre: DEBUG MARKER: == sanity-sec test 13: test nids ========================= 11:35:36 (1789572936) [ 848.806871] Lustre: DEBUG MARKER: == sanity-sec test 14: test default nodemap nid lookup === 11:36:31 (1789572991) [ 898.873387] Lustre: DEBUG MARKER: == sanity-sec test 15: test id mapping =================== 11:37:21 (1789573041) [ 1086.861414] Lustre: DEBUG MARKER: == sanity-sec test 16: test nodemap all_off fileops ====== 11:40:28 (1789573228) [ 1216.993837] Lustre: lustre-OST0001-osc-ffff9f3192134000: disconnect after 20s idle [ 1217.012857] Lustre: Skipped 1 previous similar message [ 1268.191651] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 21s idle [ 1309.152044] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 20s idle [ 1311.029586] Lustre: DEBUG MARKER: == sanity-sec test 17: test nodemap trusted_noadmin fileops ========================================================== 11:44:12 (1789573452) [ 1426.911245] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 24s idle [ 1426.930843] Lustre: Skipped 1 previous similar message [ 1437.151903] Lustre: lustre-OST0001-osc-ffff9f3192134000: disconnect after 23s idle [ 1478.115620] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 24s idle [ 1539.552723] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 24s idle [ 1585.632151] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 23s idle [ 1693.151342] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 25s idle [ 1693.156247] Lustre: Skipped 2 previous similar messages [ 1797.433519] Lustre: DEBUG MARKER: == sanity-sec test 18: test nodemap mapped_noadmin fileops ========================================================== 11:52:19 (1789573939) [ 1903.071381] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 24s idle [ 1903.082740] Lustre: Skipped 3 previous similar messages [ 2059.184266] Lustre: DEBUG MARKER: == sanity-sec test 19: test nodemap trusted_admin fileops ========================================================== 11:56:41 (1789574201) [ 2232.375488] Lustre: DEBUG MARKER: == sanity-sec test 20: test nodemap mapped_admin fileops ========================================================== 11:59:34 (1789574374) [ 2235.874822] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 23s idle [ 2235.885975] Lustre: Skipped 5 previous similar messages [ 2382.290517] Lustre: DEBUG MARKER: == sanity-sec test 21: test nodemap mapped_trusted_noadmin fileops ========================================================== 12:02:04 (1789574524) [ 2633.559040] Lustre: DEBUG MARKER: == sanity-sec test 22: test nodemap mapped_trusted_admin fileops ========================================================== 12:06:15 (1789574775) [ 2782.553712] Lustre: DEBUG MARKER: == sanity-sec test 23a: test mapped regular ACLs ========= 12:08:45 (1789574925) [ 2784.281382] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23a Need 2 clients at least [ 2786.298878] Lustre: DEBUG MARKER: == sanity-sec test 23b: test mapped default ACLs ========= 12:08:48 (1789574928) [ 2787.780825] Lustre: DEBUG MARKER: SKIP: sanity-sec test_23b Need 2 clients at least [ 2788.831176] Lustre: lustre-OST0000-osc-ffff9f3192134000: disconnect after 24s idle [ 2788.845174] Lustre: Skipped 8 previous similar messages [ 2789.676534] Lustre: DEBUG MARKER: == sanity-sec test 24: check nodemap proc files for LBUGs and Oopses ========================================================== 12:08:52 (1789574932) [ 2831.304831] Lustre: DEBUG MARKER: == sanity-sec test 25a: test save and reload nodemap config ========================================================== 12:09:33 (1789574973) [ 2834.445732] Lustre: Unmounted lustre-client [ 2865.383861] Lustre: DEBUG MARKER: === sanity-sec: start setup 12:10:07 (1789575007) === [ 2918.845899] LustreError: 66498:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 633us [ 2918.906638] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 2924.317615] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 2936.626840] Lustre: DEBUG MARKER: === sanity-sec: finish setup 12:11:18 (1789575078) === [ 2939.346890] Lustre: Unmounted lustre-client [ 2953.069467] LustreError: 67710:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 6088us [ 2953.101237] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 2960.034308] Lustre: DEBUG MARKER: == sanity-sec test 25b: test nodemap info values ========= 12:11:42 (1789575102) [ 3013.254641] Lustre: DEBUG MARKER: == sanity-sec test 25c: test yaml-compliance for nodemap ========================================================== 12:12:35 (1789575155) [ 3040.380318] Lustre: Unmounted lustre-client [ 3040.843444] LustreError: 70014:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 9838us [ 3040.891899] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3051.307707] Lustre: Unmounted lustre-client [ 3062.970325] LustreError: 70698:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 11552us [ 3063.061184] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3065.540716] Lustre: DEBUG MARKER: SKIP: sanity-sec test_26 skipping SLOW test 26 [ 3067.346581] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27a skipping excluded test 27a (base 27) [ 3069.575352] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27aa skipping excluded test 27aa (base 27) [ 3071.033698] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ab skipping excluded test 27ab (base 27) [ 3072.786340] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ac skipping excluded test 27ac (base 27) [ 3074.083693] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27ad skipping excluded test 27ad (base 27) [ 3076.088911] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27b skipping excluded test 27b (base 27) [ 3077.705202] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27c skipping excluded test 27c (base 27) [ 3079.541796] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27d skipping excluded test 27d (base 27) [ 3081.152070] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27e skipping excluded test 27e (base 27) [ 3083.070693] Lustre: DEBUG MARKER: SKIP: sanity-sec test_27f skipping excluded test 27f (base 27) [ 3084.955435] Lustre: DEBUG MARKER: == sanity-sec test 28: check shared key rotation method == 12:13:47 (1789575227) [ 3086.668657] Lustre: DEBUG MARKER: SKIP: sanity-sec test_28 need shared key feature for this test [ 3088.254221] Lustre: DEBUG MARKER: == sanity-sec test 29: check for missing shared key ====== 12:13:51 (1789575231) [ 3090.504480] Lustre: DEBUG MARKER: SKIP: sanity-sec test_29 need shared key feature for this test [ 3092.788609] Lustre: DEBUG MARKER: == sanity-sec test 30: check for invalid shared key ====== 12:13:54 (1789575234) [ 3095.062473] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30 need shared key feature for this test [ 3097.052317] Lustre: DEBUG MARKER: == sanity-sec test 30b: basic test of all different SSK flavors ========================================================== 12:13:59 (1789575239) [ 3098.855687] Lustre: DEBUG MARKER: SKIP: sanity-sec test_30b need shared key feature for this test [ 3101.132207] Lustre: DEBUG MARKER: == sanity-sec test 31: client mount option '-o network' == 12:14:03 (1789575243) [ 3105.509819] Lustre: DEBUG MARKER: SKIP: sanity-sec test_31 without lnetctl support. [ 3107.266721] Lustre: DEBUG MARKER: == sanity-sec test 32: check for mgssec ================== 12:14:09 (1789575249) [ 3110.028293] Lustre: DEBUG MARKER: SKIP: sanity-sec test_32 need shared key feature for this test [ 3112.203911] Lustre: DEBUG MARKER: == sanity-sec test 33: correct srpc flags for MGS connection ========================================================== 12:14:14 (1789575254) [ 3114.277752] Lustre: DEBUG MARKER: SKIP: sanity-sec test_33 need shared key feature for this test [ 3116.761553] Lustre: DEBUG MARKER: == sanity-sec test 34: deny_unknown on default nodemap === 12:14:18 (1789575258) [ 3145.894596] Lustre: DEBUG MARKER: == sanity-sec test 35: Check permissions when accessing changelogs ========================================================== 12:14:48 (1789575288) [ 3180.169450] LustreError: 76010:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9f31882a1000: fail to open changelog catalog: rc = -13 [ 3202.231847] Lustre: DEBUG MARKER: == sanity-sec test 36: control if clients can use encryption ========================================================== 12:15:43 (1789575343) [ 3205.530635] Lustre: Unmounted lustre-client [ 3206.188362] LustreError: 76469:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 15565us [ 3206.242919] Lustre: Test dummy encryption mode enabled [ 3206.273403] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3206.747055] llcrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-aesni)" [ 3219.030669] LustreError: 76645:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2156us [ 3219.099192] Lustre: Test dummy encryption mode enabled [ 3219.122139] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3222.894984] Lustre: Unmounted lustre-client [ 3222.897141] Lustre: Skipped 1 previous similar message [ 3228.709556] Lustre: lustre-MDT0001-mdc-ffff9f31867be000: connection denied by lustre-MDT0001_UUID: rc = -13 [ 3228.714386] LustreError: 76768:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9f31867be000: can't stat MDS #0: rc = -13 [ 3228.772524] LustreError: 76768:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -13 [ 3256.257973] LustreError: 77501:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 391us [ 3256.275502] LustreError: 77501:0:(obd_config.c:1432:process_param2_config()) Skipped 1 previous similar message [ 3256.317783] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3259.221102] Lustre: Unmounted lustre-client [ 3259.224892] Lustre: Skipped 1 previous similar message [ 3261.363295] bash (76259): drop_caches: 3 [ 3265.190924] Lustre: DEBUG MARKER: == sanity-sec test 37: simple encrypted file ============= 12:16:46 (1789575406) [ 3269.826781] Lustre: Test dummy encryption mode enabled [ 3270.389564] llcrypt: AES-256-XTS using implementation "xts-aes-aesni" [ 3282.390440] bash (77628): drop_caches: 3 [ 3285.913453] Lustre: DEBUG MARKER: == sanity-sec test 38: encrypted file with hole ========== 12:17:07 (1789575427) [ 3289.639995] LustreError: 78647:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 3009us [ 3289.650861] LustreError: 78647:0:(obd_config.c:1432:process_param2_config()) Skipped 3 previous similar messages [ 3289.714843] Lustre: Test dummy encryption mode enabled [ 3289.735530] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3289.741651] Lustre: Skipped 3 previous similar messages [ 3300.066634] Lustre: Unmounted lustre-client [ 3300.069462] Lustre: Skipped 3 previous similar messages [ 3301.283403] bash (78435): drop_caches: 3 [ 3304.863772] Lustre: DEBUG MARKER: == sanity-sec test 39: rewrite data in already encrypted page ========================================================== 12:17:25 (1789575445) [ 3309.464571] Lustre: Test dummy encryption mode enabled [ 3321.302481] bash (79222): drop_caches: 3 [ 3324.825792] Lustre: DEBUG MARKER: == sanity-sec test 40: exercise size of encrypted file === 12:17:45 (1789575465) [ 3329.110589] Lustre: Test dummy encryption mode enabled [ 3336.459730] bash (80002): drop_caches: 3 [ 3349.020986] bash (80002): drop_caches: 3 [ 3352.029556] Lustre: DEBUG MARKER: == sanity-sec test 41: test race on encrypted file size (1) ========================================================== 12:18:13 (1789575493) [ 3354.992299] LustreError: 81199:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2115us [ 3355.003024] LustreError: 81199:0:(obd_config.c:1432:process_param2_config()) Skipped 6 previous similar messages [ 3355.030675] Lustre: Test dummy encryption mode enabled [ 3355.041608] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3355.043322] Lustre: Skipped 6 previous similar messages [ 3381.784419] Lustre: Unmounted lustre-client [ 3381.790857] Lustre: Skipped 6 previous similar messages [ 3383.021944] bash (80989): drop_caches: 3 [ 3386.403474] Lustre: DEBUG MARKER: == sanity-sec test 42: test race on encrypted file size (2) ========================================================== 12:18:47 (1789575527) [ 3389.547836] Lustre: Test dummy encryption mode enabled [ 3423.052195] bash (81797): drop_caches: 3 [ 3427.226636] Lustre: DEBUG MARKER: == sanity-sec test 43: test race on encrypted file size (3) ========================================================== 12:19:27 (1789575567) [ 3464.531900] bash (82654): drop_caches: 3 [ 3467.205518] Lustre: DEBUG MARKER: == sanity-sec test 44: encrypted file access semantics: direct IO ========================================================== 12:20:09 (1789575609) [ 3469.382754] Lustre: DEBUG MARKER: SKIP: sanity-sec test_44 This test needs vmtouch utility [ 3471.316175] Lustre: DEBUG MARKER: == sanity-sec test 45: encrypted file access semantics: MMAP ========================================================== 12:20:13 (1789575613) [ 3474.767504] Lustre: Test dummy encryption mode enabled [ 3474.771016] Lustre: Skipped 3 previous similar messages [ 3485.866957] LustreError: 84546:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 2506us [ 3485.874774] LustreError: 84546:0:(obd_config.c:1432:process_param2_config()) Skipped 8 previous similar messages [ 3485.991581] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3485.993581] Lustre: Skipped 8 previous similar messages [ 3486.674484] bash (83812): drop_caches: 3 [ 3489.954311] Lustre: DEBUG MARKER: == sanity-sec test 46: encrypted file access semantics without key ========================================================== 12:20:31 (1789575631) [ 3495.373587] bash (84593): drop_caches: 3 [ 3500.163791] bash (84593): drop_caches: 3 [ 3501.505463] LustreError: 84969:0:(llite_lib.c:4132:ll_prep_md_op_data()) lustre: failed to setup filename: rc = -126 [ 3511.409215] Lustre: Unmounted lustre-client [ 3511.417419] Lustre: Skipped 10 previous similar messages [ 3512.647825] bash (84593): drop_caches: 3 [ 3516.217285] Lustre: DEBUG MARKER: == sanity-sec test 47: encrypted file access semantics: rename/link ========================================================== 12:20:57 (1789575657) [ 3529.480877] bash (85501): drop_caches: 3 [ 3556.477592] bash (85501): drop_caches: 3 [ 3570.028438] bash (85501): drop_caches: 3 [ 3573.447530] Lustre: DEBUG MARKER: == sanity-sec test 48a: encrypted file access semantics: truncate ========================================================== 12:21:54 (1789575714) [ 3578.477502] bash (86647): drop_caches: 3 [ 3582.825623] LustreError: 2391:0:(lmv_obd.c:211:lmv_notify()) activation of lustre-MDT0000_UUID failed: -22 [ 3583.646547] bash (86647): drop_caches: 3 [ 3594.438449] bash (86647): drop_caches: 3 [ 3597.695328] Lustre: DEBUG MARKER: == sanity-sec test 48b: encrypted file: concurrent truncate ========================================================== 12:22:19 (1789575739) [ 3599.644792] Lustre: DEBUG MARKER: SKIP: sanity-sec test_48b Need at least 2 clients [ 3602.092725] Lustre: DEBUG MARKER: == sanity-sec test 49: Avoid getxattr for encryption context ========================================================== 12:22:24 (1789575744) [ 3605.492495] Lustre: Test dummy encryption mode enabled [ 3605.499383] Lustre: Skipped 3 previous similar messages [ 3606.671256] bash (87905): drop_caches: 3 [ 3607.623727] bash (87905): drop_caches: 3 [ 3609.275350] bash (87905): drop_caches: 3 [ 3610.649143] bash (87905): drop_caches: 3 [ 3611.993581] bash (87905): drop_caches: 3 [ 3613.562296] bash (87905): drop_caches: 3 [ 3614.810076] bash (87905): drop_caches: 3 [ 3615.719139] bash (87905): drop_caches: 3 [ 3616.982294] bash (87905): drop_caches: 3 [ 3617.638260] bash (87905): drop_caches: 3 [ 3618.937941] bash (87905): drop_caches: 3 [ 3619.985765] bash (87905): drop_caches: 3 [ 3651.001224] bash (87905): drop_caches: 3 [ 3654.075524] Lustre: DEBUG MARKER: == sanity-sec test 50: DoM encrypted file ================ 12:23:15 (1789575795) [ 3657.861722] bash (88968): drop_caches: 3 [ 3658.691332] bash (88968): drop_caches: 3 [ 3659.251187] Lustre: 89231:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 3659.585481] bash (88968): drop_caches: 3 [ 3660.116219] bash (88968): drop_caches: 3 [ 3660.633828] Lustre: 89256:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 3661.036807] bash (88968): drop_caches: 3 [ 3661.740283] bash (88968): drop_caches: 3 [ 3662.394715] Lustre: 89282:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 3662.865579] bash (88968): drop_caches: 3 [ 3663.446748] bash (88968): drop_caches: 3 [ 3664.289559] bash (88968): drop_caches: 3 [ 3664.965131] bash (88968): drop_caches: 3 [ 3665.355854] Lustre: 89332:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x2:0x0] with data: rc = -126 [ 3665.367674] Lustre: 89332:0:(file.c:676:ll_dom_finish_open()) Skipped 1 previous similar message [ 3665.776097] bash (88968): drop_caches: 3 [ 3666.292944] bash (88968): drop_caches: 3 [ 3667.325903] bash (88968): drop_caches: 3 [ 3667.892448] bash (88968): drop_caches: 3 [ 3668.875609] bash (88968): drop_caches: 3 [ 3669.700616] bash (88968): drop_caches: 3 [ 3671.198651] bash (88968): drop_caches: 3 [ 3671.792830] bash (88968): drop_caches: 3 [ 3672.851967] bash (88968): drop_caches: 3 [ 3673.485847] bash (88968): drop_caches: 3 [ 3674.505438] bash (88968): drop_caches: 3 [ 3675.181234] bash (88968): drop_caches: 3 [ 3675.734946] Lustre: 89485:0:(file.c:676:ll_dom_finish_open()) lustre: cannot fill page 0 for [0x200000413:0x3:0x0] with data: rc = -126 [ 3675.749479] Lustre: 89485:0:(file.c:676:ll_dom_finish_open()) Skipped 2 previous similar messages [ 3676.220280] bash (88968): drop_caches: 3 [ 3676.865324] bash (88968): drop_caches: 3 [ 3678.602213] bash (88968): drop_caches: 3 [ 3679.306278] bash (88968): drop_caches: 3 [ 3695.096600] bash (88968): drop_caches: 3 [ 3699.061438] Lustre: DEBUG MARKER: == sanity-sec test 51: FS capabilities =================== 12:24:00 (1789575840) [ 3752.493597] Lustre: DEBUG MARKER: == sanity-sec test 52: Mirrored encrypted file =========== 12:24:54 (1789575894) [ 3755.579566] LustreError: 91618:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 3295us [ 3755.585488] LustreError: 91618:0:(obd_config.c:1432:process_param2_config()) Skipped 13 previous similar messages [ 3755.625939] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 3755.629591] Lustre: Skipped 13 previous similar messages [ 3758.623368] LustreError: 91699:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9f31882a4000: inode [0x200000415:0x4:0x0] mdc close failed: rc = -22 [ 3767.237948] bash (91407): drop_caches: 3 [ 3769.664704] Lustre: DEBUG MARKER: == sanity-sec test 53: Mixed PAGE_SIZE clients =========== 12:25:11 (1789575911) [ 3771.263535] Lustre: DEBUG MARKER: SKIP: sanity-sec test_53 Need 64K PAGE_SIZE client [ 3773.152442] Lustre: DEBUG MARKER: == sanity-sec test 54: Encryption policies with fscrypt == 12:25:15 (1789575915) [ 3775.275535] Lustre: DEBUG MARKER: SKIP: sanity-sec test_54 This test needs fscrypt userspace tool [ 3777.109673] Lustre: DEBUG MARKER: == sanity-sec test 55: access with seteuid =============== 12:25:19 (1789575919) [ 3780.548856] Lustre: Unmounted lustre-client [ 3780.553098] Lustre: Skipped 12 previous similar messages [ 3814.070970] Lustre: DEBUG MARKER: == sanity-sec test 56: FIEMAP on encrypted file ========== 12:25:56 (1789575956) [ 3824.415711] bash (93966): drop_caches: 3 [ 3826.957481] Lustre: DEBUG MARKER: == sanity-sec test 57: security.c/encryption.c xattr protection ========================================================== 12:26:08 (1789575968) [ 3838.653351] bash (94744): drop_caches: 3 [ 3841.571844] Lustre: DEBUG MARKER: == sanity-sec test 58: access to enc file's xattrs ======= 12:26:23 (1789575983) [ 3844.830034] bash (95556): drop_caches: 3 [ 4039.206574] bash (95556): drop_caches: 3 [ 4298.366121] Lustre: Unmounted lustre-client [ 4298.373047] Lustre: Skipped 6 previous similar messages [ 4299.040275] LustreError: 107379:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 978us [ 4299.061207] LustreError: 107379:0:(obd_config.c:1432:process_param2_config()) Skipped 8 previous similar messages [ 4299.132125] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 4299.143957] Lustre: Skipped 8 previous similar messages [ 4299.703760] bash (95556): drop_caches: 3 [ 4302.804904] Lustre: DEBUG MARKER: == sanity-sec test 59a: mirror resync of encrypted files without key ========================================================== 12:34:04 (1789576444) [ 4306.952493] Lustre: Test dummy encryption mode enabled [ 4306.954195] Lustre: Skipped 5 previous similar messages [ 4310.850230] bash (107427): drop_caches: 3 [ 4312.759992] bash (107427): drop_caches: 3 [ 4327.476514] bash (107427): drop_caches: 3 [ 4331.064277] Lustre: DEBUG MARKER: == sanity-sec test 59b: migrate/extend/split of encrypted files without key ========================================================== 12:34:31 (1789576471) [ 4339.740653] bash (108402): drop_caches: 3 [ 4340.694729] bash (108402): drop_caches: 3 [ 4348.260580] bash (108402): drop_caches: 3 [ 4350.458571] bash (108402): drop_caches: 3 [ 4359.346339] LustreError: 2391:0:(lmv_obd.c:211:lmv_notify()) activation of lustre-MDT0000_UUID failed: -22 [ 4359.733682] bash (108402): drop_caches: 3 [ 4360.420450] LustreError: 109150:0:(file.c:251:ll_close_inode_openhandle()) lustre-clilmv-ffff9f318522e000: inode [0x20000041d:0x2:0x0] mdc close failed: rc = -22 [ 4361.174400] bash (108402): drop_caches: 3 [ 4375.857328] bash (108402): drop_caches: 3 [ 4379.297614] Lustre: DEBUG MARKER: == sanity-sec test 59c: MDT migrate of encrypted files without key ========================================================== 12:35:20 (1789576520) [ 4387.587776] bash (109790): drop_caches: 3 [ 4388.699939] bash (109790): drop_caches: 3 [ 4401.139707] bash (109790): drop_caches: 3 [ 4405.906915] Lustre: DEBUG MARKER: == sanity-sec test 60: Subdirmount of encrypted dir ====== 12:35:46 (1789576546) [ 4411.686381] bash (110680): drop_caches: 3 [ 4418.116351] bash (110680): drop_caches: 3 [ 4431.674440] bash (110680): drop_caches: 3 [ 4434.402871] Lustre: DEBUG MARKER: == sanity-sec test 61: Nodemap enforces read-only mount == 12:36:16 (1789576576) [ 4470.973777] Lustre: lustre-MDT0000-mdc-ffff9f31a6651000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 4470.976322] Lustre: Skipped 1 previous similar message [ 4470.997140] LustreError: 112338:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9f31a6651000: can't stat MDS #0: rc = -30 [ 4471.011349] LustreError: 112338:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9f31a6651000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 4474.098922] Lustre: lustre-MDT0001-mdc-ffff9f3185224000: connection denied by lustre-MDT0001_UUID: rc = -30 [ 4474.116221] Lustre: Skipped 1 previous similar message [ 4474.119553] LustreError: 112425:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9f3185224000: can't stat MDS #0: rc = -30 [ 4474.127425] LustreError: 112425:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9f3185224000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 4480.454540] Lustre: lustre-MDT0000-mdc-ffff9f3188bd7000: connection denied by lustre-MDT0000_UUID: rc = -30 [ 4480.468835] Lustre: Skipped 1 previous similar message [ 4480.472800] LustreError: 112597:0:(lmv_obd.c:1471:lmv_statfs()) lustre-MDT0000-mdc-ffff9f3188bd7000: can't stat MDS #0: rc = -30 [ 4480.482672] LustreError: 112597:0:(llite_lib.c:317:ll_force_readonly()) lustre-clilmv-ffff9f3188bd7000: mount failed due to read-only MDT, forcing read-only mount: rc = -30 [ 4498.037854] Lustre: DEBUG MARKER: == sanity-sec test 62: e2fsck with encrypted files ======= 12:37:20 (1789576640) [ 4637.817189] Lustre: DEBUG MARKER: Using TIMEOUT=20 [ 4650.098286] LustreError: 2391:0:(lmv_obd.c:211:lmv_notify()) activation of lustre-MDT0001_UUID failed: -22 [ 4650.732380] bash (113256): drop_caches: 3 [ 4653.432641] Lustre: DEBUG MARKER: == sanity-sec test 63: fid2path with encrypted files ===== 12:39:55 (1789576795) [ 4655.810550] Lustre: DEBUG MARKER: SKIP: sanity-sec test_63 This test needs fscrypt userspace tool [ 4657.772290] Lustre: DEBUG MARKER: == sanity-sec test 64a: Nodemap enforces file_perms RBAC roles ========================================================== 12:40:00 (1789576800) [ 4726.149301] Lustre: DEBUG MARKER: == sanity-sec test 64b: Nodemap enforces dne_ops RBAC roles ========================================================== 12:41:08 (1789576868) [ 4792.612494] Lustre: DEBUG MARKER: == sanity-sec test 64c: Nodemap enforces quota related RBAC roles ========================================================== 12:42:15 (1789576935) [ 4828.042800] LustreError: 120334:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9f31a6b78800: ptlrpc_queue_wait failed: rc = -1 [ 4828.561216] LustreError: 120346:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9f31a6b78800: ptlrpc_queue_wait failed: rc = -1 [ 4828.570685] LustreError: 120346:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 11 previous similar messages [ 4850.933297] LustreError: 120709:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9f31a6b78800: ptlrpc_queue_wait failed: rc = -1 [ 4850.945157] LustreError: 120709:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 11 previous similar messages [ 4877.908642] Lustre: DEBUG MARKER: == sanity-sec test 64d: Nodemap enforces byfid_ops RBAC roles ========================================================== 12:43:40 (1789577020) [ 4946.543981] Lustre: DEBUG MARKER: == sanity-sec test 64e: Nodemap enforces chlg_ops RBAC roles ========================================================== 12:44:48 (1789577088) [ 4978.281878] LustreError: 123611:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9f31a6b78800: fail to open changelog catalog: rc = -13 [ 4978.292137] LustreError: 123611:0:(mdc_changelog.c:301:chlg_load()) Skipped 1 previous similar message [ 5004.050114] LustreError: 124072:0:(mdc_changelog.c:301:chlg_load()) lustre-MDT0000-mdc-ffff9f31a6b78800: fail to open changelog catalog: rc = -13 [ 5004.070283] LustreError: 124072:0:(mdc_changelog.c:301:chlg_load()) Skipped 1 previous similar message [ 5032.777689] Lustre: DEBUG MARKER: == sanity-sec test 64f: Nodemap enforces fscrypt_admin RBAC roles ========================================================== 12:46:15 (1789577175) [ 5035.334335] Lustre: DEBUG MARKER: SKIP: sanity-sec test_64f Need fscrypt, skip fscrypt_admin role [ 5037.996029] Lustre: DEBUG MARKER: == sanity-sec test 64g: Nodemap enforces server_upcall RBAC role ========================================================== 12:46:19 (1789577179) [ 5104.798410] Lustre: DEBUG MARKER: == sanity-sec test 64h: Nodemap enforces local_admin RBAC roles ========================================================== 12:47:26 (1789577246) [ 5128.769223] LustreError: 127355:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9f31a6b78800: ptlrpc_queue_wait failed: rc = -1 [ 5128.785869] LustreError: 127355:0:(mdc_request.c:2191:mdc_quotactl()) Skipped 2 previous similar messages [ 5133.877529] LustreError: 127439:0:(mdc_request.c:2191:mdc_quotactl()) lustre-MDT0000-mdc-ffff9f31a6b78800: ptlrpc_queue_wait failed: rc = -1 [ 5155.662835] Lustre: DEBUG MARKER: == sanity-sec test 64i: Nodemap quota enforcement with local_admin RBAC and offsets ========================================================== 12:48:18 (1789577298) [ 5310.897249] Lustre: Unmounted lustre-client [ 5310.905679] Lustre: Skipped 28 previous similar messages [ 5317.685185] LustreError: 131950:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 452us [ 5317.695627] LustreError: 131950:0:(obd_config.c:1432:process_param2_config()) Skipped 28 previous similar messages [ 5317.753485] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 5317.755921] Lustre: Skipped 28 previous similar messages [ 5320.674286] Lustre: DEBUG MARKER: == sanity-sec test 64j: Nodemap enforces projid_set RBAC role ========================================================== 12:51:03 (1789577463) [ 5391.388808] Lustre: DEBUG MARKER: == sanity-sec test 64k: Nodemap enforces foreign_ops RBAC roles ========================================================== 12:52:13 (1789577533) [ 5436.647462] Lustre: DEBUG MARKER: == sanity-sec test 64l: Nodemap enforces immutable_flags RBAC role ========================================================== 12:52:59 (1789577579) [ 5479.871165] Lustre: DEBUG MARKER: == sanity-sec test 65: lfs find -printf %La and --attrs support ========================================================== 12:53:42 (1789577622) [ 5484.225387] Lustre: Test dummy encryption mode enabled [ 5484.227197] Lustre: Skipped 9 previous similar messages [ 5497.806669] bash (135942): drop_caches: 3 [ 5501.685825] Lustre: DEBUG MARKER: == sanity-sec test 68: all config logs are processed ===== 12:54:02 (1789577642) [ 5505.033960] LustreError: 2391:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d sleeping for 20000ms [ 5510.175369] LustreError: 137166:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.118@tcp: failed processing log, type 1: rc = -110 [ 5525.087136] LustreError: 2391:0:(niobuf.c:882:ptl_send_rpc()) cfs_fail_timeout id 51d awake [ 5539.094561] Lustre: DEBUG MARKER: == sanity-sec test 69: check upcall incorrect values ===== 12:54:41 (1789577681) [ 5552.561925] Lustre: DEBUG MARKER: == sanity-sec test 70: targets have local copy of sptlrpc llog ========================================================== 12:54:54 (1789577694) [ 5554.934653] Lustre: DEBUG MARKER: SKIP: sanity-sec test_70 need shared key feature for this test [ 5556.767332] Lustre: DEBUG MARKER: == sanity-sec test 71: encryption does not remove project flag ========================================================== 12:54:59 (1789577699) [ 5559.573754] Lustre: DEBUG MARKER: SKIP: sanity-sec test_71 Need fscrypt [ 5561.960820] Lustre: DEBUG MARKER: == sanity-sec test 72a: dynamic nodemap properties on OSS ========================================================== 12:55:03 (1789577703) [ 5664.401508] Lustre: DEBUG MARKER: == sanity-sec test 72b: dynamic nodemap properties on MDS ========================================================== 12:56:46 (1789577806) [ 5763.409386] Lustre: DEBUG MARKER: == sanity-sec test 72c: child_raise_privileges nodemap property ========================================================== 12:58:25 (1789577905) [ 5810.911973] Lustre: DEBUG MARKER: == sanity-sec test 72d: fileset inheritance for dynamic nodemap ========================================================== 12:59:13 (1789577953) [ 5880.639445] Lustre: DEBUG MARKER: == sanity-sec test 72e: dynamic nodemap reclassify ======= 13:00:23 (1789578023) [ 5917.079425] Lustre: Unmounted lustre-client [ 5917.096613] Lustre: Skipped 5 previous similar messages [ 5927.917462] LustreError: 145699:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 14465us [ 5927.930748] LustreError: 145699:0:(obd_config.c:1432:process_param2_config()) Skipped 5 previous similar messages [ 5928.010869] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 5928.016090] Lustre: Skipped 5 previous similar messages [ 5930.309691] Lustre: DEBUG MARKER: == sanity-sec test 72f: fileset_modify on dynamic nodemap ========================================================== 13:01:12 (1789578072) [ 6002.320724] Lustre: DEBUG MARKER: == sanity-sec test 73: encrypted names in changelogs ===== 13:02:24 (1789578144) [ 6004.513784] Lustre: DEBUG MARKER: SKIP: sanity-sec test_73 Need fscrypt [ 6006.212938] Lustre: DEBUG MARKER: == sanity-sec test 74: Set nodemap deny_mount flag ======= 13:02:28 (1789578148) [ 6036.210573] LustreError: 147925:0:(llite_lib.c:605:client_common_fill_super()) lustre-clilmv-ffff9f31a1318800: cannot mds_connect: rc = -1 [ 6036.322637] LustreError: 147925:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -1 [ 6058.894859] Lustre: DEBUG MARKER: == sanity-sec test 75: check uid/gid/projid are set on OST and MDT for various RPCs ========================================================== 13:03:21 (1789578201) [ 6117.657945] Lustre: DEBUG MARKER: == sanity-sec test 75a: test resource fs IDs against nodemap offset ========================================================== 13:04:20 (1789578260) [ 6121.406891] Lustre: DEBUG MARKER: SKIP: sanity-sec test_75a need at least two clients [ 6123.767943] Lustre: DEBUG MARKER: == sanity-sec test 75b: test resource ID repair ========== 13:04:25 (1789578265) [ 6259.774613] bash (152209): drop_caches: 3 [ 6276.305995] bash (152563): drop_caches: 3 [ 6313.069965] Lustre: DEBUG MARKER: == sanity-sec test 76: suppgroups and gid mapping ======== 13:07:35 (1789578455) [ 6357.544246] Lustre: DEBUG MARKER: == sanity-sec test 77: root offsetting =================== 13:08:18 (1789578498) [ 6408.552407] Lustre: DEBUG MARKER: == sanity-sec test 78: nodemap stats ===================== 13:09:11 (1789578551) [ 6450.486511] Lustre: DEBUG MARKER: == sanity-sec test 79: ssk for nodemap identification ==== 13:09:52 (1789578592) [ 6452.284995] Lustre: DEBUG MARKER: SKIP: sanity-sec test_79 Need shared key feature for this test [ 6454.258782] Lustre: DEBUG MARKER: == sanity-sec test 81a: nodemap ban list ================= 13:09:56 (1789578596) [ 6456.379434] Lustre: DEBUG MARKER: test_81a 29065 [ 6481.475887] Lustre: This client was banned by administrative request for file system lustre. All requests will get Operation not permitted. [ 6481.484471] LustreError: 157845:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 6521.951507] LustreError: 158424:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 6521.964345] LustreError: 158424:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 6536.470778] Lustre: Unmounted lustre-client [ 6536.480033] Lustre: Skipped 8 previous similar messages [ 6541.923682] LustreError: 158651:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.118@tcp: failed processing log, type 1: rc = -110 [ 6680.543382] LustreError: MGC192.168.202.118@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 6680.580365] LustreError: 158651:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 6686.337207] LustreError: 158802:0:(obd_config.c:1432:process_param2_config()) lctl: error invoking upcall /usr/sbin/lctl set_param nodemap..fileset=/c0dir: rc = -2; time 996us [ 6686.346457] LustreError: 158802:0:(obd_config.c:1432:process_param2_config()) Skipped 8 previous similar messages [ 6686.394394] Lustre: Mounted lustre-client - version 2.17.58_39_g6aa67ea [ 6686.399871] Lustre: Skipped 7 previous similar messages [ 6692.397832] LustreError: 158894:0:(file.c:6167:ll_inode_revalidate_fini()) lustre: revalidate FID [0x200000007:0x1:0x0] error: rc = -1 [ 6692.408080] LustreError: 158894:0:(file.c:6167:ll_inode_revalidate_fini()) Skipped 1 previous similar message [ 6698.016120] LustreError: 158932:0:(mgc_request.c:233:do_config_log_add()) MGC192.168.202.118@tcp: failed processing log, type 1: rc = -110 [ 6836.194278] LustreError: MGC192.168.202.118@tcp: Confguration from log lustre-client failed from MGS -110. Communication error between node & MGS, a bad configuration, or other errors. See syslog for more info [ 6836.225791] LustreError: 158932:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -110 [ 6860.308816] Lustre: DEBUG MARKER: == sanity-sec test 81b: banned client does not block other ========================================================== 13:16:42 (1789579002) [ 6862.241883] Lustre: DEBUG MARKER: SKIP: sanity-sec test_81b Need 2 clients [ 6864.222881] Lustre: DEBUG MARKER: == sanity-sec test 82: export lock revoked after nodemap change ========================================================== 13:16:46 (1789579006) [ 6930.045886] Lustre: DEBUG MARKER: == sanity-sec test 83: Suppgids for cross-MDT ops ======== 13:17:52 (1789579072) [ 6941.650324] Lustre: DEBUG MARKER: == sanity-sec test 84: do not squash trusted ids ========= 13:18:03 (1789579083) [ 6974.222326] Lustre: DEBUG MARKER: == sanity-sec test 85: forbid squashing to UID/GID 0 ===== 13:18:36 (1789579116) [ 7010.516599] Lustre: DEBUG MARKER: == sanity-sec test 93: incremental RBAC role modifications ========================================================== 13:19:12 (1789579152) [ 7078.939185] Lustre: DEBUG MARKER: == sanity-sec test 100: SSK automatic prime generation, binary/ASCII server keys ========================================================== 13:20:21 (1789579221) [ 7080.319494] Lustre: DEBUG MARKER: SKIP: sanity-sec test_100 Need shared key feature for this test [ 7081.984837] Lustre: DEBUG MARKER: == sanity-sec test 101: lgss_sk -a and -l support for ascii-encoded SSK keys ========================================================== 13:20:24 (1789579224) [ 7083.633909] Lustre: DEBUG MARKER: SKIP: sanity-sec test_101 Need shared key feature for this test [ 7085.562705] Lustre: DEBUG MARKER: == sanity-sec test 102: SSK automatic key loading from mount point ========================================================== 13:20:27 (1789579227) [ 7087.563968] Lustre: DEBUG MARKER: SKIP: sanity-sec test_102 Need shared key feature for this test [ 7089.637100] Lustre: DEBUG MARKER: == sanity-sec test 103: Multiple SSK keys on server side ========================================================== 13:20:31 (1789579231) [ 7091.360630] Lustre: DEBUG MARKER: SKIP: sanity-sec test_103 Need shared key feature for this test [ 7093.453759] Lustre: DEBUG MARKER: == sanity-sec test 104: SSK key removal from keyring ===== 13:20:35 (1789579235) [ 7094.844785] Lustre: DEBUG MARKER: SKIP: sanity-sec test_104 Need shared key feature for this test [ 7096.483859] Lustre: DEBUG MARKER: == sanity-sec test 105: update nodemap membership on flavor change ========================================================== 13:20:39 (1789579239) [ 7098.388280] Lustre: DEBUG MARKER: SKIP: sanity-sec test_105 Need shared key feature for this test [ 7099.886760] Lustre: DEBUG MARKER: == sanity-sec test 106: switch nodemap to gssonly ======== 13:20:42 (1789579242) [ 7101.629568] Lustre: DEBUG MARKER: SKIP: sanity-sec test_106 Need shared key feature for this test [ 7103.230277] Lustre: DEBUG MARKER: == sanity-sec test 200: sk_load_key broadens SSK key perms without @u linked ========================================================== 13:20:45 (1789579245) [ 7104.695545] Lustre: DEBUG MARKER: SKIP: sanity-sec test_200 Need shared key feature for this test [ 7106.292590] Lustre: DEBUG MARKER: == sanity-sec test 201: per-network sptlrpc flavor rule overrides default ========================================================== 13:20:48 (1789579248) [ 7107.803871] Lustre: DEBUG MARKER: SKIP: sanity-sec test_201 Need shared key feature for this test [ 7109.653770] Lustre: DEBUG MARKER: == sanity-sec test 300: test user_principal mount option parsing ========================================================== 13:20:52 (1789579252) [ 7111.223241] Lustre: DEBUG MARKER: Mount with user_principal=mock_iam_test [ 7117.281674] Lustre: DEBUG MARKER: Mount with only user_principal (should fail) [ 7117.611727] LustreError: Unknown option 'user_principal', won't mount. [ 7117.622263] LustreError: 169274:0:(super25.c:179:lustre_fill_super()) llite: Unable to mount : rc = -22 [ 7119.028343] Lustre: DEBUG MARKER: Mount failed as expected with only -o user_principal [ 7125.756794] Lustre: DEBUG MARKER: cleanup: ====================================================== [ 7127.134437] Lustre: DEBUG MARKER: == sanity-sec test complete, duration 6811 sec =========== 13:21:09 (1789579269) [ 7128.525110] Lustre: DEBUG MARKER: === sanity-sec: start cleanup 13:21:11 (1789579271) === [ 7131.135493] Lustre: DEBUG MARKER: === sanity-sec: finish cleanup 13:21:13 (1789579273) === [ 7186.194256] Key type lgssc unregistered [ 7186.373815] LNet: 171261:0:(lib-ptl.c:964:lnet_clear_lazy_portal()) Active lazy portal 0 on exit [ 7186.377207] LNetError: 171261:0:(acceptor.c:252:lnet_acceptor_remove_socket()) Interface ens2 not found [ 7186.388640] LNet: Removed LNI 192.168.202.18@tcp [ 7187.154261] Key type .llcrypt unregistered [ 7187.157869] Key type ._llcrypt unregistered